Apple led cinema display 24inch User Manual
Here you can view all the pages of manual Apple led cinema display 24inch User Manual. The Apple manuals for Display are available online for free. You can easily download all the documents as PDF.
Page 61
LED Cinema Display (24-inch) Take Apart — Logic Board 61 2010-11-25
3 Disconnect 11 cable
connectors:
1. power
2. blower
3. camera (922-8670)
4. sensor/blower
(922-8672)
5. sensor/LCD
(922-8671)
6. microphone
7. subwoofer
8. left speaker
9. right speaker
10. USB uplink from
all-in-one cable
12. LCD function
interface (922-8669;
if not previously
removed with LCD
panel)
For your reference:
#11 indicates location
of LED driver
(backlight) cable...
Page 62
LED Cinema Display (24-inch) Take Apart — Logic Board 62 2010-11-25 Replacement Reassembly is an exact reversal of the steps. Note: Connect 10 cables with reverse side of MLB facing you, then flip board over and connect USB uplink cable (#10). 1. power 2. blower 3. camera 4. sensor/blower 5. sensor/LCD 6. microphone 7. subwoofer 8. left speaker (4-pin) 9. right speaker (3-pin) 12. LCD function interface Tip: Tape down the USB uplink cable (#10) to ensure it doesn’t...
Page 63
LED Cinema Display (24-inch) Take Apart — Power Supply 63 2010-11-25 First Steps Remove: • G lass Panel • L CD Panel Warning: HIGH VOLTAGE: Use extreme caution when working around the power supply, which contains a high-voltage capacitor that may remain charged for several minutes even when the computer is unplugged. Never touch the leads on the top side of the power supply, especially those near the warning sign. Tools • ESD wrist strap • T orx T10 screwdriver Power Supply
Page 64
LED Cinema Display (24-inch) Take Apart — Power Supply 64 2010-11-25 Removal 1 Remove 4 screws: T10, 922-8685 2 Disconnect 3 cables: 1 from logic board and 2 from below the power supply. 3 Preserve adhesive “butterfly” strip for reuse. Replacement Reassembly is an exact reversal of the steps.
Page 65
LED Cinema Display (24-inch) Take Apart — Fan (Blower) 65 2010-11-25 First Steps Remove: • G lass Panel • L CD Panel Tools • ESD wrist strap • T orx T10 screwdriver Fan (Blower)
Page 66
LED Cinema Display (24-inch) Take Apart — Fan (Blower) 66 2010-11-25 Removal 1 Remove 3 screws: T10, 922-8684 2 Disconnect 2 cables from logic board. 3 Remove ambient temp sensor cable (922-8672) from fan, preserving black tape for reuse.
Page 67
LED Cinema Display (24-inch) Take Apart — Fan (Blower) 67 2010-11-25 Replacement Reassembly is an exact reversal of the steps above, with 3 notes: Note 1: The ambient temp sensor cable (922- 8672) must extend exactly 1cm from the plastic retaining loop on the fan casing so it will sit the proper distance from rear housing when installed. Incorrect sensor placement can lead to false temperature readings and unusual fan behavior. Note 2: Ensure the pressure wall section attached to fan...
Page 68
LED Cinema Display (24-inch) Take Apart — Camera 68 2010-11-25 First Steps Remove: • G lass Panel • L CD Panel Tools • ESD wrist strap • T orx T10 screwdriver • B lack stick Camera
Page 69
LED Cinema Display (24-inch) Take Apart — Camera 69 2010-11-25 Removal 1 Remove 2 screws: T10, 922-8680 2 Lift camera out of rear housing. 3 Lift clear tape and remove camera cable from camera. Reassembly Note: Thermal paste is required between camera and rear housing. Use a black stick to remove thermal paste from old camera and reapply to new camera (areas circled). Note: A syringe of thermal paste is available as needed, Apple part# 922- 9625, good for 5 applications.
Page 70
LED Cinema Display (24-inch) Take Apart — Subwoofer 70 2010-11-25 First Steps Remove: • G lass Panel • L CD Panel Tools • ESD wrist strap • T orx T10 screwdriver Subwoofer