Apple imac usb 2 0 User Manual
Have a look at the manual Apple imac usb 2 0 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 109
100 - iMac (USB 2.0) Take Apart
Display, 17" Flat Panel
Replacing the 17Display Panel
1. After connecting the display cables, position the display into the rear housing. Place
the display into the rear housing, sliding it into position, pushing it in the dir\
ection of
the arrows. Note: The display mates with tabs/slots in the rear housing. If the display
doesn’t fit properly and you can’t install the three screws along the bottom of the
housing, check that the display is properly seated in...](http://img.usermanuals.tech/thumb/462/38804/w64_imac-usb-2-0-108.png "Page 109
100 - iMac (USB 2.0) Take Apart
Display, 17\" Flat Panel
Replacing the 17Display Panel
1. After connecting the display cables, position the display into the rear housing. Place
the display into the rear housing, sliding it into position, pushing it in the dir\
ection of
the arrows. Note: The display mates with tabs/slots in the rear housing. If the display
doesn’t fit properly and you can’t install the three screws along the bottom of the
housing, check that the display is properly seated in...")
![Page 110
iMac (USB 2.0) Take Apart - 101
Display, 17" Flat Panel 3. Check the alignment of the rear housing and the flat panel display. If the display
doesn’t slide into the tabs/slots on the rear housing, a white line s\
hows across the
back of the rear housing (see below).
4. A properly installed display will have no white line showing across the back of the rear housing (see below), and the three display-to-housing screw holes align perfectly.](http://img.usermanuals.tech/thumb/462/38804/w64_imac-usb-2-0-109.png "Page 110
iMac (USB 2.0) Take Apart - 101
Display, 17\" Flat Panel 3. Check the alignment of the rear housing and the flat panel display. If the display
doesn’t slide into the tabs/slots on the rear housing, a white line s\
hows across the
back of the rear housing (see below).
4. A properly installed display will have no white line showing across the back of the rear housing (see below), and the three display-to-housing screw holes align perfectly.")
102 - iMac (USB 2.0) Take Apart Display, 15" Flat Panel Display, 15 Flat Panel Tools This procedure requires the following tools: • 1.5 mm hex tool • Plastic stylus to lift the panel Part Location Preliminary Steps Before you begin, do the following: • Position the computer in the service stand.
iMac (USB 2.0) Take Apart - 103 Display, 15" Flat Panel Procedure 1. Remove ten screws connecting the back cover to the flat panel LCD display. 2. It is not necessary to remove the two screws circled below unless you are removing the neck or the panel shield.
104 - iMac (USB 2.0) Take Apart Display, 15" Flat Panel 3. With a plastic tool, raise the display to access cables underneath the flat panel. 4. Disconnect the inverter cable shown below.
iMac (USB 2.0) Take Apart - 105 Display, 15" Flat Panel 5. Raise the display to disconnect the circled items: The inverter cable, the microphone, and the power-on LED.
106 - iMac (USB 2.0) Take Apart Display, 15" Flat Panel 6. This shows a close up of the video cable, ferrite bead, and video cable clip. After removing the kapton tape, carefully use a screwdriver to pry the ferrite bead from the video cable clip. Pry the ferrite bead from the side or from the back. Note: The ferrite bead is fragile and could break if a screwdriver is placed in the middle of the ferrite bead and is used as leverage to remove the bead. 7. Peel the black tape back to expose the video cable. Gently pull the video cable from the connector.
iMac (USB 2.0) Take Apart - 107 Display, 15" Flat Panel 8. After disconnecting all the cables, you are left with the 15" LCD flat panel service part (661-2582).
108 - iMac (USB 2.0) Take Apart Inverter, 20" Display Inverter, 20 Display Tools • Torx-10 screwdriver Part Location Preliminary Steps Before you begin, do the following: • Position the computer in the service stand. • Lift the flat panel to access the inverter.
iMac (USB 2.0) Take Apart - 109 Inverter, 20" Display Procedure 1. Carefully raise the display and disconnect the inverter cables. 2. Remove the four inverter screws (circled below) and disconnect the inverter cable on the left side of the board. 3. Lift the inverter board off the rear housing.
110 - iMac (USB 2.0) Take Apart Inverter, 17" Display Inverter, 17 Display Tools Torx-10 screwdriver. Part Location Preliminary Steps Before you begin, do the following: • Position the computer in the service stand. • Remove the flat panel display.
iMac (USB 2.0) Take Apart - 111 Inverter, 17" Display Procedure 1. Remove the four panel screws (circled below) to access the inverter on the left side of the panel. 2. Remove the kapton tape holding the cables in place.