Apple ibook g4 early 2004 User Manual
Here you can view all the pages of manual Apple ibook g4 early 2004 User Manual. The Apple manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 101
iBook G4 Take Apart - 100 Optical Drive5.Warning: Handle the optical drive at the sides only. Do not touch or press anywhere else on the drive. Without straining any cables, tilt up the optical drive and lift it out the drive.
Page 102
101 - iBook G4 Take Apart Optical Drive 6. Remove the two identical screws holding the cable bracket to the optical drive. 7. Remove the cable bracket. Note: When reassembling the computer, transfer the cable bracket to the replacement drive. 8. Peel off the tape from the optical drive, and disconnect the ribbon cable. Note: When reassembling the computer, transfer the ribbon cable to the replacement drive.
Page 103
iBook G4 Take Apart - 102 Optical Drive9. Remove the screw holding the mounting bracket to the bezel. 10. Remove the screws that hold the mounting bracket to the optical drive. Important: When reassembling the computer, transfer the mounting bracket to the replacement drive. Replacement Warning: Make sure you use the shorter screw to secure the mounting bracket to the bezel.
Page 104
103 - iBook G4 Take Apart Optical Drive 11.Caution: The bezel and optical drive case is a soft material. Be especially careful when removing the bezel from the optical drive. With the pointed end of a black stick, gently press the three tabs, and tilt the bezel up and off of the drive. 12. Install the replacement optical drive, and reassemble and test the computer. Replacement Note: When installing the replacement optical drive, align the front of the drive bezel to the outer edge of the frame...
Page 105
iBook G4 Take Apart - 104 How to Remove a Stuck Disc from the Slot-Load How to Remove a Stuck Disc from the Slot-Load Drive The following instructions explain how to remove a disc that is stuck in the slot-load optical drive. Important: When a disc becomes stuck in the slot-load optical drive, it makes the drive unusable. Make sure you have a replacement drive available. Tools This procedure requires the following tools: • ESD wriststrap and mat • #0 Phillips screwdriver • Black stick (or other...
Page 106
105 - iBook G4 Take Apart How to Remove a Stuck Disc from the Slot-Load Procedure 1. Remove the four identical screws that hold the top cover to the drive. 2. Slide the top cover approximately 2 mm toward the back of the drive. Lift up the top cover to remove it.
Page 107
iBook G4 Take Apart - 106 How to Remove a Stuck Disc from the Slot-Load 3. Check the placement of the disc. It is either clamped to the turntable at the center of the disc, or it is wedged under one or more posts at the outer edge of the disc. 4. Holding the edge of the disc, press on the center clamp or hold the posts steady as you remove the disc from the drive. Important: Do not touch any key components located near the disc. 5. Replace the top cover on the drive so that the small hooks on the...
Page 108
107 - iBook G4 Take Apart Display Module Display Module Tools • Soft cloth • #0 Phillips screwdriver • Black stick (or other nonconductive nylon or plastic tool) Note: To organize the screws you remove from the computer, use a tray with divided compartments (such as a plastic ice cube tray). Part Location Preliminary Steps Before you begin, remove the following: • Battery • Keyboard and RAM shield • AirPort Extreme Card • Memory card
Page 109
iBook G4 Take Apart - 108 Display Module• Bottom case • Bottom shield • DC-in board • Top case • Top shield • Modem Procedure 1. With the computer on a soft cloth, note the routing of the thin, black microphone cable and the LVDS (low voltage data signal) cable. 2. Disconnect the microphone cable from the logic board near the hard drive. 3. Pull up the flexible tab to disconnect the LVDS cable from the logic board.
Page 110
109 - iBook G4 Take Apart Display Module 4. Without straining the cables, lift them up from the logic board. 5. Peel off any tape holds the cables to the frame. 6. While supporting the display, tilt up the chassis, and disconnect the inverter cable from the underside of the logic board.