AOC Le22h067 User Manual

10
Controls & Connections
Speaker Speaker
Power Indicator
IR ReceiverVolume +
Volume -
Channel
Channel
Menu
Input
Power
1. VOL +  Press to increase the sound volume level.
2. VOL - Press to decrease the sound volume level.
3. CH ▲ Press to select the next higher program number.
4. CH ▼ Press to select the next lower program number.
5. MENUPress to open or exit the OSD (on-screen display) 
menu.
6. INPUT Press to select the input source.
7.
 Power Press to turn on / off (standby) the TV set. 
HDMI 1HDMI 2...

11
Buttons located at the right side of the TV will operate the same as these buttons on the remote control. 
!
MTS
CC
PRE CH
Display
EPGWide
Add Fav
COMP
FavMU
/ ExitEN
Button Description
POWER Press to turn on and off the TV.
COMPTV/ AV/ 
COMP/ HDMI/
PCPress TV, AV, COMP or HDMI/PC separately to select the input directly. 
PR
0-9  Press 0-9 to select a channel; the channel changes after two seconds. 
! PRE CHPRE CHPress to go back to the previous TV channel or exit from the OSD when 
displaying menu...

12
Set-Up 
Inserting Batteries into the Remote control 
Insert two size AAA batteries (supplied) to the diagram inside the battery compartment of the remote control.
Attaching the Base
IMPORTANT: The Base of the AOC HDTV must be assembled prior to usage.
Place the TV set facing down on a soft and flat surface (blanket, foam, cloth, etc.) to prevent any  1. 
damage to TV set.   
Carefully align and insert the Base to the stand 2. 
Gently push the Base towards the TV until the locking mechanism locks into...

13
Connecting TV 
Cable System or VHF/UHF Antenna System 
You can enjoy standard-definition and high-definition digital programming (if available in your area), along with standard-definition analog 
programming. 
This TV is capable of receiving unscrambled digital programming for both cable and external VHF/UHF antenna. 
It is strongly recommended that you connect the antenna/cable input using a 75-ohm coaxial cable to receive optimum picture quality. A 300-ohm 
twin lead cable can be easily affected by...

14
Composite/ S-Video Signal Connection
S-VIDEOS-VIDEO
S-VIDEO
S-VIDEO AV
AV IN AV IN
Audio
PC Connection
Use the TV as a monitor for your PC shown below with the HD15 to HD15 connection. This TV can also be connected to a PC with DVI or HDMI 
output. (Refer to the separate Quick Setup Guide.)
PC
VGA IN
Connect the PC IN jack to the PC using the HD15- HD15 cable with ferrite core (analog RGB) and audio cable. 
If the PC is connected to the TV and no signal has been input from the PC for more than 30...

15
PC Input Signal Reference Chart 
After connecting the PC to the TV, set the output signal from the PC according to the chart below. 
Presetting PC Mode
Standard  Resolution  Horizontal Frequency (kHz)  Vertical Frequency (Hz) 
VESA 640 x 480 31.469 59.94
VESA 800 x 600 37.879 60.317
VESA 1024 x 768 48.363 60.004
VESA 1280 x 720 44.772 59.855
VESA 1280 x 768 47.396 59.995
VESA 1280 x 1024 63.981 60.02
VESA 1440 x 900 55.469 59.901
VESA 1680 x 1050 65.29 59.954
VESA 1920 x 1080 67.5 60
Video Input...

16
USING AOC TV
Turning the TV On and Off
You can turn on the TV by using power switch button on the TV set or on the remote controller.
Navigate: Select:
OK French SpanishEnglish Initial Wizard (1/8)
Please select language...
Next Cancel
Initial Setting
When you first start up this AOC HDTV set, please follow the Initial Wizard to your AOC HDTV.
1. Selecting Language.
Select your preferred language:  English, Spanish or French
1Press ▲/▼ to select “Language”, and press OK.
2. Selecting Time mode....

17
A. Selecting Time Zone.
Inital Wizard (3/8)
Please select Time Zone...
NST MST
AST PST
EST AKST
CSTHST
Navigate: Select:
OK Previous Cancel
1Press ▲/▼/◄/► to select “Time Zone” which you located then press OK.
 

18
B. Manually enter the time.
Jan 2010 Year
1 Month
12:02 AM Day
Time
OK
Previous Cancel
Navigate: Select:
OK Initial Wizard (3/8)
Please enter the time...
Year 
1Press ▲/▼ to select “Year” then press OK.
2
Press ◄/► to adjust then press OK.
Month 
1Press ▲/▼to select “Month” then press OK.
2
Press ◄/► to adjust then press OK.
Day 
1Press ▲/▼ to select “Day” then press OK.
2
Press ◄/► to adjust then press OK.
Time 
1Press ▲/▼ to select “Time” then press OK.
2
Press ◄/► to select “Hour”, “Minute” or...

19
3. Select “Eco” mode or “Vivid” mode.
When you turn on TV in the first time, you can choose “Eco” mode to decrease backlight level to save the power consumption or “Vivid” mode to 
enhance picture contrast and sharpness.
ENTER
VividEco Initial Wizard (4/8)
Please select Eco/Vivid mode...
Previous Cancel
Navigate: Select:
1Press ▲/▼ to select “Eco” or “Vivid” for display setting.
4. Select TV RF tuning band. 
CableAir Initial Wizard (5/8)
Please select TV RF tuning band...
Previous Cancel
Navigate:...