AOC Le22h067 User Manual

							10
Controls & Connections
Speaker Speaker
Power Indicator
IR ReceiverVolume +
Volume -
Channel
Channel
Menu
Input
Power
1. VOL +  Press to increase the sound volume level.
2. VOL - Press to decrease the sound volume level.
3. CH ▲ Press to select the next higher program number.
4. CH ▼ Press to select the next lower program number.
5. MENUPress to open or exit the OSD (on-screen display) 
menu.
6. INPUT Press to select the input source.
7.
 Power Press to turn on / off (standby) the TV set. 
HDMI 1HDMI 2 USB
SPDIF PC In
USB/Service
HDMI 2 Headphone Jack
HDMI 1 Component In S-VideoVHF/UHF Cable In
AV in L-Audio-R
Item Description
Headphone JackConnects to your headphones. If your headphones do not match the jack, use a suitable plug adapter (not 
supplied). While headphones are connected, the TV speakers are muted.
SPDIF
* 
(Optical Digital Audio Out)Connect an external sound system with optical cable to the SPDIF out jack on the back of your TV to the SPDIF 
IN jack and to the amplifier or receiver.
AV IN (AV/S-VIDEO) / 
L-AUDIO-R Connects to the COMPOSITE VIDEO output or S-Video output jack from your video equipment that has 
COMPOSITE or S-Video VIDEO, and audio (L/R) jacks can connect audio source to your TV. When connected, 
S-Video will take priority over Composite video (Yellow jack).
USB/Service Insert USB storage device to the USB 2.0 port to view photos (JPEG only).
S-VIDEO InputConnects to the S-VIDEO output jack on your camcorder or other video equipment that has S-VIDEO. The 
S-VIDEO provides better picture quality than composite video. The audio input connector was shared with 
COMPOSITE VIDEO IN.
HDMI IN 1/ 2HDMI (High-Definition Multimedia Interface) provides an uncompressed, all-digital audio/video interface between 
this TV and any HDMI-equipped audio/video equipment, such as a set-top box, DVD player, Blu-ray Disc player, 
A/V receiver as well as PC. HDMI supports enhanced, or high-definition video, plus digital audio. 
If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the HDMI IN (with DVI-to-HDMI 
cable or adapter) jack, and connect the audio jack to the PC AUDIO IN jacks of HDMI IN. 
DVI-to-HDMI cable DVI-to-HDMI adapter
HDMI connection is necessary to view 480i, 480p, 720p, 1080i and 1080p formats. 
Be sure to use only an HDMI cable that bears the HDMI logo. 
PC IN (RGB/AUDIO)Connects to a personal computer’s video output connector using HD15-HD15 cable (analog RGB). Can also be 
connected to other analog RGB equipment. See “PC Input Signal Reference Chart” on page 15 for the signals that 
can be displayed.
For some Apple Macintosh computers, it may be necessary to use an adapter (not supplied). If this is the case, 
connect the adapter to the computer before connecting the HD15-HD15 cable. 
If the picture is noisy, flickering or not clear, adjust Phase and Pitch of Screen settings. 
Component IN 
(1080p/1080i/ 
720p/480p/480i)/ 
L-AUDIO-RConnects to your TV’s component video (YPbPr ) and audio (L/R) jacks. Component video provides better picture 
quality than the S-VIDEO or the composite video connections. Component video (YPbPr) connection is necessary 
to view 480i, 480p, 720p, 1080i and 1080p formats. 
VHF/UHF/Cable InputRF (Radio Frequency or modulated signal design used as the carrier for television broadcasts.) input that 
connects to your Cable or VHF/UHF antenna.
* SPDIFSony/Philips Digital Interconnect Format. S/PDIF is mostly used to transmit compressed multichannel audio from a media player to an amplifier/receiver.
 
						

							11
Buttons located at the right side of the TV will operate the same as these buttons on the remote control. 
!
MTS
CC
PRE CH
Display
EPGWide
Add Fav
COMP
FavMU
/ ExitEN
Button Description
POWER Press to turn on and off the TV.
COMPTV/ AV/ 
COMP/ HDMI/
PCPress TV, AV, COMP or HDMI/PC separately to select the input directly. 
PR
0-9  Press 0-9 to select a channel; the channel changes after two seconds. 
! PRE CHPRE CHPress to go back to the previous TV channel or exit from the OSD when 
displaying menu items and settings.
VOL +/- Press to adjust the volume.
SOURCEPress to display the list of External Inputs. Press repeatedly to toggle 
through the inputs. 
MUTE Press to mute the sound. Press again or press VOL+ to restore the sound.
CH +/-Press to scan through channels. To scan quickly through channels, press 
and hold down either + or -.
 /  /  / Move left, up, down or right to select the available option or adjust the 
setting in OSD menu. 
OK Press to confirm the selected item or setting.
MU
/ ExitENMENU/EXITPress to display or close a list of convenient functions and menu 
shortcuts. The OSD (On Screen Display) menu items vary based on input 
and content. 
DisplayDISPLAY Press once to display the information pertaining to the channel and/or 
program when available. The OSD (On Screen Display) will time out in a 
few seconds or press again to immediately turn off the display. 
Add FavAdd Fav Press to add channel to Favorite List. 
FavFAV Channel Press to display the Favorite Channel List.
EPGEPGPress to display digital program guide in TV mode. It may show current 
channel name, program name, time, rating, and summaries, depending on 
the information provided by the broadcaster.
Play/PauseExecute “Play/Pause” when you control HDMI interface device via HDMI 
CEC.
Stop Execute “Stop” when you control HDMI interface device via HDMI CEC.
WideWIDEPress repeatedly to step through the Wide Mode settings: Normal Mode, 
Wide mode, Zoom 1 Mode, Zoom 2 Mode, and HDMI PC mode (Only 
available in HDMI Input). 
PhotoPress to display the USB thumbnail browser. This is activated only if the 
USB storage device is plugged into the USB hub.
Freeze Press to freeze the displayed picture.
MTSMTS*Press to activate the NTSC TV sounds, such as: Stereo, SAP** or Mono 
tone and languages of DTV.
SLEEP***Press repeatedly to cycle through the available sleep timer, 5, 10, 15, 30, 
60, 90, 120 180 and 240 minutes to turn off TV automatically.
PICTUREPress repeatedly to cycle through the available picture modes: Vivid, 
Standard, Eco, Movie and Personal. The picture modes can also be 
accessed in the Picture settings. For details, see section- Adjust Picture 
Setting. 
AUDIOPress repeatedly to cycle through the available sound modes: Music, 
Speech and Personal. The sound modes can also be accessed in the 
Sound settings. For details, see section- Adjust Audio Setting.
V-ChipPress to lock Parental Control temporarily. (After setting the restricted 
table of MPAA, Motion Picture Association of America or TV Rating.)
CCCCPress repeatedly to change the closed caption type as CC Off /
CC On / CC On With Mute.
* Multichannel Television Sound (MTS)The broadcasting standard, which allows stereo sounds to be transmitted with the TV picture.** Second Audio Program (SAP)Another or additional audio channel provided for in the Multichannel Television Sound (MTS) broadcast standard. A monaural sound track included within 
the recorded or video signal (usually containing a second language translation for the displayed program).
*** SleepYou can set a time period for which the TV will be turned off automatically.
 
						

							12
Set-Up 
Inserting Batteries into the Remote control 
Insert two size AAA batteries (supplied) to the diagram inside the battery compartment of the remote control.
Attaching the Base
IMPORTANT: The Base of the AOC HDTV must be assembled prior to usage.
Place the TV set facing down on a soft and flat surface (blanket, foam, cloth, etc.) to prevent any  1. 
damage to TV set.   
Carefully align and insert the Base to the stand 2. 
Gently push the Base towards the TV until the locking mechanism locks into place.  3. 
Please refer to the “Important Usage instructions” in the above. 4. 
Wall-Mounting 
Please install on a wall by using a Wall-Mount Bracket (sold separately). Before mounting the TV on a wall, the Table-Top Stand must be 
removed from the TV.  Follow the simple steps below to remove the Table-Top Stand:
Disconnect all the cables from the TV. 1. 
Gently lay the TV, face down, onto a level and stable surface covered with a thick and soft cloth. Make sure the Table-Top Stand is hanging  2. 
over the edge. 
Remove the screws as shown in the illustration for your model and pull the Table-Top Stand out.  3. 
Do not remove any other screws from the TV.  4. 
Do not remove the Table-Top Stand for any reason other than to Wall-Mount 5.  the TV. 
Be sure to store the removed screws and Table-Top Stand in a safe place until you are ready to reattach the Table-Top Stand. Keep the  6. 
screws away from small children. 
For bracket installation, refer to the instruction guide provided by the Wall-Mount 7.  Bracket model for your TV. Sufficient expertise is required in 
installing this TV, especially to determine the strength of the wall for withstanding the TV’s weight. 
For product protection and safety reasons, AOC strongly recommends that you use the Wall-Mount 8.  Bracket model designed for your TV and 
the Wall-Mounting of your TV should be performed by AOC dealer or licensed contractor. 
123
Note:  100 mm x 100 mm wall mount bracket & M4 screws (Screws length: 10mm and pitch: 0.7mm) are not included.  
Please contact your local distributor.
 
						

							13
Connecting TV 
Cable System or VHF/UHF Antenna System 
You can enjoy standard-definition and high-definition digital programming (if available in your area), along with standard-definition analog 
programming. 
This TV is capable of receiving unscrambled digital programming for both cable and external VHF/UHF antenna. 
It is strongly recommended that you connect the antenna/cable input using a 75-ohm coaxial cable to receive optimum picture quality. A 300-ohm 
twin lead cable can be easily affected by radio frequency interference, resulting in signal degradation. 
Cable or VHF/UHF(or VHF only)
75-ohm coaxial
cable (supplled)Rear of TV
VHF/UHF input
TUNER
High Definition Interface
You can enjoy high-definition programming by subscribing to a high-definition cable service or a high-definition satellite service. For the best 
possible picture, make sure you connect this equipment to your TV via the HDMI or component video (with audio) input on the back of your TV. 
HDMI Connection
HDMI
HDMI
HDMI
HDMI
HD Multimedia Interface
HDMI IN 1 / 2
If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the HDMI IN (with DVI-to-HDMI cable or adapter) jack and 
connect the audio jack to the PC AUDIO IN jacks.
Component Signal Connection
Y Pb Pr
Component Video Input
Component INLRYPbPrLRYPbPr
Audio
 
						

							14
Composite/ S-Video Signal Connection
S-VIDEOS-VIDEO
S-VIDEO
S-VIDEO AV
AV IN AV IN
Audio
PC Connection
Use the TV as a monitor for your PC shown below with the HD15 to HD15 connection. This TV can also be connected to a PC with DVI or HDMI 
output. (Refer to the separate Quick Setup Guide.)
PC
VGA IN
Connect the PC IN jack to the PC using the HD15- HD15 cable with ferrite core (analog RGB) and audio cable. 
If the PC is connected to the TV and no signal has been input from the PC for more than 30 seconds, the TV enters the standby mode  automatically. 
External sound Connection
Turn off the AOC HDTV and Sound Device and connect the Audio Out jack or SPDIF  jack on the rear of AOC HDTV.
Connect an audio cable to the audio output connectors associated with the Audio Out (R/L) and SPDIF on the TV Set and connect the other 
 end to the audio connectors associated with the Audio input of the External Sound.
SPDIF
SONY Philips Digital Interface
SPDIF IN
 
						

							15
PC Input Signal Reference Chart 
After connecting the PC to the TV, set the output signal from the PC according to the chart below. 
Presetting PC Mode
Standard  Resolution  Horizontal Frequency (kHz)  Vertical Frequency (Hz) 
VESA 640 x 480 31.469 59.94
VESA 800 x 600 37.879 60.317
VESA 1024 x 768 48.363 60.004
VESA 1280 x 720 44.772 59.855
VESA 1280 x 768 47.396 59.995
VESA 1280 x 1024 63.981 60.02
VESA 1440 x 900 55.469 59.901
VESA 1680 x 1050 65.29 59.954
VESA 1920 x 1080 67.5 60
Video Input Signal Reference Chart 
After connecting the video input to the TV, set the output signal from the video input according to the chart below. 
Presetting Video Mode
Standard  Resolution  Horizontal Frequency (kHz)  Vertical Frequency (Hz) 
SD 480i 15.734 60
SD 480P 31.5 60
HD 720P 45 60
HD 1080i 33.75 60
FHD 1080p 67.5 60
Standard Definition Interface
You can also enjoy traditional program by using a DVD player or VCR Player. Connect this equipment to your TV via the Composite Input or 
S-Video Input on the back of your TV. 
Refer to the Quick Setup Guide (supplied) when connecting other equipment to your TV.
 
						

							16
USING AOC TV
Turning the TV On and Off
You can turn on the TV by using power switch button on the TV set or on the remote controller.
Navigate: Select:
OK French SpanishEnglish Initial Wizard (1/8)
Please select language...
Next Cancel
Initial Setting
When you first start up this AOC HDTV set, please follow the Initial Wizard to your AOC HDTV.
1. Selecting Language.
Select your preferred language:  English, Spanish or French
1Press ▲/▼ to select “Language”, and press OK.
2. Selecting Time mode.
ManualAuto Initial Wizard (2/8)
Please select Time mode...
Previous Cancel
Navigate: Select:
OK
1Press ▲/▼ to select “Auto” or “Manual” for Time Mode.
 
						

							17
A. Selecting Time Zone.
Inital Wizard (3/8)
Please select Time Zone...
NST MST
AST PST
EST AKST
CSTHST
Navigate: Select:
OK Previous Cancel
1Press ▲/▼/◄/► to select “Time Zone” which you located then press OK.
 
						

							18
B. Manually enter the time.
Jan 2010 Year
1 Month
12:02 AM Day
Time
OK
Previous Cancel
Navigate: Select:
OK Initial Wizard (3/8)
Please enter the time...
Year 
1Press ▲/▼ to select “Year” then press OK.
2
Press ◄/► to adjust then press OK.
Month 
1Press ▲/▼to select “Month” then press OK.
2
Press ◄/► to adjust then press OK.
Day 
1Press ▲/▼ to select “Day” then press OK.
2
Press ◄/► to adjust then press OK.
Time 
1Press ▲/▼ to select “Time” then press OK.
2
Press ◄/► to select “Hour”, “Minute” or “AM/PM” then press OK.
3
Press ▲/▼ to adjust then press OK.
 
						

							19
3. Select “Eco” mode or “Vivid” mode.
When you turn on TV in the first time, you can choose “Eco” mode to decrease backlight level to save the power consumption or “Vivid” mode to 
enhance picture contrast and sharpness.
ENTER
VividEco Initial Wizard (4/8)
Please select Eco/Vivid mode...
Previous Cancel
Navigate: Select:
1Press ▲/▼ to select “Eco” or “Vivid” for display setting.
4. Select TV RF tuning band. 
CableAir Initial Wizard (5/8)
Please select TV RF tuning band...
Previous Cancel
Navigate: Select:
OK
1Press ▲/▼ to select “Air” or “Cable” for RF Tuning setting. Press OK will execute channel searching.