AOC E936swa User Manual

							
Windows Vista 
 
1. Click Start  and Control Panel. Then, double-click on Appearance and Personalization. 
    
  
2. Click Personalization and then Display Settings. 
   
 
3. Click Advanced Settings.... 
    
 
 41
 
						

							
4. Click Properties in the Monitor tab. If the Properties button is deactivated, it means the configuration for your 
monitor is completed. The monitor can be used as is. 
If the message Windows needs... is displayed,  as shown in the figure below, click Continue. 
   
 
5. Click Update Driver... in the Driver tab.   
   
 
6. Check the Browse my computer for driver software checkbox and click Let me pick from a list of device drivers 
on my computer. 
 
 
7. Click on the Have disk... button, then click on the Browse... button and then select the appropriate drive 
F:\Driver (CD-ROM Drive).   
8. Select your monitor model  and click on the Next button. 
9. Click Close → Close → OK →  OK on the following screens displayed in sequence. 
 42
 
						

							
Windows 7 
1.Start Windows® 7 
 
2.Click on the Start button and then click on  Control Panel. 
 
 
3. Click on the Display icon. 
 
 
4.Ckick on the  “Change display settings”  button.  
 
 
 43
 
						

							
5.Click the “Advanced Settings” button.  
 
 
6.Click the  “Monitor”  tab and then click the  “Properties” button. 
 
 
7.Click the “Driver” tab.   
 
 44
 
						

							
8. Open the Update Driver Software-Generic PnP Monitor window by clicking on “Update Driver... “and then 
click the  Browse my computer for driver software  button.  
 
 
9. Select Let me pick from a list of  device drivers on my computer.  
 
 
10. Click the “Have Disk”  button. Click on the  “Browse” button and navigate to the following directory:   
X:\Driver\module name    (where X is the drive letter designator for the CD-ROM drive). 
 
  
 45
 
						

							
 46
11. Select the xxx.inf file and click the  “Open” button. Click the  “OK” button.  
 
12. Select your monitor model and click the “Next”  button. The files will be copied from the CD to your hard disk 
drive.  
 
13. Close all open windows and remove the CD.   
 
14. Restart the system. The system will  automatically select the maximum refresh rate and corresponding Color 
Matching Profiles.   
 
 
 
						

							
i-Menu 
 
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on 
screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation 
guide.  
 47
 
						

							
Troubleshoot 
 
Problem & Question 
 
Possible Solutions 
 
 
Power LED Is Not ON 
 
Make sure the power button is ON and the Power Cord is properly connected 
to a grounded power outlet and to the monitor.   
 
 
 
 
 
 
 
 
 
 
No images on the screen 
 
Is the power cord connected properly? 
Check the power cord connection and power supply. 
Is the cable connected correctly? 
(Connected using the D-sub cable) 
Check the DB-15 cable connection.    
(Connected using the DVI cable) 
Check the DVI cable connection.  
* DVI input is not available on every model. 
If the power is on, reboot the computer to see the initial screen (the login 
screen), which can be seen. 
If the initial screen (the login screen) ap pears, boot the computer in the 
applicable mode (the safe mode for Windows ME/XP/2000) and then change 
the frequency of the video card. 
(Refer to the Setting t he Optimal Resolution) 
If the initial screen (the login screen) d oes not appear, contact the Service 
Center or your dealer. 
Can you see Input Not Supported on the screen? 
You can see this message when the signal from the video card exceeds the 
maximum resolution and frequency that the monitor can handle properly. 
Adjust the maximum resolution and fr equency that the monitor can handle 
properly. 
Make sure the AOC Monitor Drivers are installed. 
 
Picture Is Fuzzy & Has 
Ghosting Shadowing Problem   
 
Adjust the Contrast and Brightness Controls.   
Press to auto adjust.   
Make sure you are not using an ext ension cable or switch box. We 
recommend plugging the monitor directly to the video card output connector 
on the back .   
 
Picture Bounces, Flickers Or 
Wave Pattern Appears In The 
Picture 
Move electrical devices that may cause electrical interference as far away 
from the monitor as possible.   
Use the maximum refresh rate your monitor is capable of at the resolution 
your are using.   
 48
 
						

							
 49
 
 
 
 
Monitor Is Stuck In Active 
Off-Mode 
 
The Computer Power Switch should be in the ON position.   
The Computer Video Card should be snugly fitted in its slot.   
Make sure the monitors video cable is properly connected to the computer. 
Inspect the monitors video cable and make sure no pin is bent.   
Make sure your computer is operational by hitting the CAPS LOCK key on 
the keyboard while observing the CAPS LOCK LED. The LED should either 
turn ON or OFF after hitting the CAPS LOCK key.   
 
Missing one of the primary 
colors (RED, GREEN, or 
BLUE) 
 
Inspect the monitors video cable and make sure that no pin is damaged.   
Make sure the monitors video cable is properly connected to the computer. 
 
Screen image is not centered 
or sized properly 
 
Adjust H-Position and V-Position or press hot-key (AUTO).   
 
Picture has color defects 
(white does not look white) 
 
Adjust RGB color or select desired color temperature.   
 
Horizontal or vertical 
disturbances on the screen 
 
Use Windows 95/98/2000/ME/XP sh ut-down mode Adjust CLOCK and 
FOCUS.  
Press to auto-adjust.   
 
						

							
 50
Specification 
General Specification 
Model name e936Swa 
Driving system   TFT Color LCD   
Viewable Image Size 47.0cm diagonal 
Pixel pitch   0.3mm(H) x 0.3mm(V)   
Video   R, G, B Analog lnterface   
Separate Sync.   H/V TTL 
Display Color  16.7M Colors  
LCD Panel 
Dot Clock  85.5MHz  
Horizontal scan range   30 kHz - 80 kHz 
Horizontal scan 
Size(Maximum)  409.8mm  
Vertical scan range   55 Hz - 75 Hz   
Vertical scan 
Size(Maximum)  230.4mm  
Optimal preset resolution 1366x768 (60 Hz)   
Highest preset resolution 1366x768 (60 Hz)   
Plug & Play   VESA DDC2B/CI   
Input Connector   D-Sub 15pin   
Input Video Signal   Analog: 0.7Vp-p(standard), 75 OHM 
Power Source   100-240V~, 50/60Hz   
Typical < 25W   Power Consumption   Standby < 1 W   
USB Downstream port (A 
type ) To USB device, loading < 100mA 
off timer 0~24hours Select timing  to turn off the monitor. 
Resolution 
Speakers 1.5W x 2 
Connector Type   15-pin Mini D-Sub   
Signal Cable Type   Detachable   
Height (with base)   358.66mm 
Width  463.14mm 
Depth  186mm 
Weight (monitor only)   3.25 kg 
Physical 
Characteristics  
Dimensions & Weight:  
Weight (with packaging)   4.85 kg