AOC 2436vwa User Manual

							٢١  | Page  
 
4. Click Properties in the Monitor tab. If the Properties button is deactivated, it means the 
configuration for your monitor is completed. The monitor can be used as is. 
If the message Windows needs... is displayed, as shown in the figure below, click Continue. 
 
5. Click Update Driver... in the Driver tab.  
 
 
6. Check the Browse my computer for driver software checkbox and click Let me pick from a list of 
device drivers on my computer. 
  
 
						

							٢٢  | Page  
 
6.  Click on the Have disk... button, then click on the Browse... button and then select the appropriate 
drive F:\Driver (CD-ROM Drive).  
8. Select your monitor model and click on the Next button. 
9. Click Close → Close → OK → OK on the following screens displayed in sequence.  
 
 
 
I_MENU 
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen 
menus instead of the OSD button on the monitor. Please click here
 to setup the software. To complete installation, 
please follow the installation guide .  
 
 
 
 
 
 
 
 
 
 
 
 
 
						

							٢٣  | Page  
 
PRODUCT INFORMATION 
 
LCD Panel  
model name 2436Vwa 
Driving system  TFT Color LCD  
Viewable Image Size 598.09mm diagonal 
Pixel pitch  0.2715mm(H) x 0.2715mm(V) 
Video  R, G, B Analog lnterface & Digital Interface 
Separate Sync.  H/V TTL 
Display Color  16.7M Colors  
Dot Clock  148.5 MHz  
Resolution  
Horizontal scan range  30 kHz - 80 kHz 
Horizontal scan 
Size(Maximum)  521.28mm 
Vertical scan range  55 Hz - 75 Hz  
Vertical scan 
Size(Maximum)  293.22mm  
Optimal preset resolution 1920 x 1080 (60 Hz) 
Highest preset resolution 1920 x 1080 (60 Hz)  
Plug & Play  VESA DDC2B/CI  
Input Connector  D-Sub 15pin & DVI-D  
Input Video Signal  Analog: 0.7Vp-p(standard), 75 OHM, TMDS 
Power Source  100-240V～, 50/60Hz  
Power Consumption  Typical < 49 W  
Standby < 1 W  
USB Downstream port (A 
type ) To USB device, loading < 100mA 
off timer 0~24hours Select timing to turn off the monitor. 
Speakers 2W x 2 
Physical 
Characteristics  
Connector Type  15-pin Mini D-Sub& DVI-D  
Signal Cable Type  Detachable  
Dimensions & Weight:  
Height (with base) 425.47 mm 
Width  582.14 mm 
Depth  206mm 
Weight (monitor 
only)  5.5 kg 
Weight (with 
packaging)  7.0 kg 
Environmental  
Temperature:  Operating  0° to 40°  
Non-Operating  -20°to 60° 
Humidity:  Operating  10% to 85% (non-condensing)  
Non-Operating  5% to 80% (non-condensing)  
Altitude:  Operating  0~ 3000m (0~ 10000 ft )  
Non-Operating  0~ 5000m (0~ 15000 ft )  
 
 
 
 
 
 
 
						

							٢۴  | Page  
 
Preset Display Modes  
 
STAND RESOLUTION  
HORIZONTAL  
FREQUENCY(kHZ) 
VERTICAL  
FREQUENCY(Hz) 
VGA 640×480 @60Hz 31.469  59.940  
VGA 640×480 @67Hz  35.000  66.667  
VGA 640×480 @72Hz  37.861  72.809  
VGA 640×480 @75Hz  37.500  75.000  
Dos-mode 720×400 @70Hz  31.469  70.087  
SVGA 800×600 @56Hz  35.156  56.250  
SVGA 800×600 @60Hz  37.879  60.317  
SVGA 800×600 @72Hz 48.077  72.188  
SVGA 800×600 @75Hz  46.875  75.000  
SVGA 832×624 @75Hz  49.725  74.550  
XGA 1024×768 @60Hz   48.363  60.004  
XGA 1024×768 @70Hz  56.476  70.069  
XGA 1024×768 @75Hz  60.023  75.029  
XGA 1024×768 @75Hz  60.241  74.927 
*** 1280×960 @60Hz  60.000  60.000  
SXGA 1280×1024 @60Hz  63.981  60.02 
SXGA 1280×1024 @75Hz 79.976  75.025  
WXGA+ 1440×900 @60Hz   55.935  59.887  
WSXGA 1680X1050 @60Hz   65.290  59.954  
HD 1920×1080@60Hz 67.500  60.000  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
						

							٢۵  | Page  
 
Pin Assignments 
 
 
Pin Number 15-Pin Side of the Signal Cable 
1 Video-Red 
2 Video-Green 
3 Video-Blue 
4 N.C. 
5 Detect Cable 
6 GND-R 
7 GND-G 
8 GND-B 
9 +5V 
10 Ground 
11 N.C. 
12 DDC-Serial data 
13 H-sync 
14 V-sync 
15 DDC-Serial clock 
PLUG & PLAY 
Plug & Play DDC2B Feature 
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. 
 It allows the monitor to inform the host system of its identity and, depending on the level of DDC used,  
communicate additional information about its display capabilities. 
The DDC2B is a bi-directional data channel based on the I
2C protocol. The host can request EDID information 
 over the DDC2B channel. 
 
 
 
 
 
 
 
 
 
 
						

							٢۶  | Page  
 
TROUBLESHOOT 
Problem & 
Question Possible Solutions 
Power LED Is 
Not ON 
 Make sure the power button is ON and the Power Cord is properly connected to a 
grounded power outlet and to the monitor.  
No images on 
the screen 
Is the power cord connected properly? 
  Check the power cord connection and power supply. 
Is the cable connected correctly? 
  
(Connected using the D-sub cable) 
Check the DB-15 cable connection.   
(Connected using the DVI cable) 
Check the DVI cable connection.  
* DVI input is not available on every model. 
If the power is on, reboot the computer to see the initial screen (the login 
screen), which can be seen. 
  
If the initial screen (the login screen) appears, boot the computer in the applicable 
mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the 
video card. 
(Refer to the Setting the Optimal Resolution) 
If the initial screen (the login screen) does not appear, contact the Service Center or 
your dealer.  
Can you see Input Not Supported on the screen? 
  
You can see this message when the signal from the video card exceeds the maximum 
resolution and frequency that the monitor can handle properly. 
Adjust the maximum resolution and frequency that the monitor can handle properly.  
Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are available at 
: here)  
Picture Is Fuzzy 
& Has Ghosting 
Shadowing 
Problem  
 Adjust the Contrast and Brightness Controls.  
 Press to auto adjust.  
 Make sure you are not using an extension cable or switch box. We recommend 
plugging the monitor directly to the video card output connector on the back .  
Picture 
Bounces, 
Flickers Or 
Wave Pattern 
Appears In The 
Picture 
 Move electrical devices that may cause electrical interference as far away from the 
monitor as possible.  
 Use the maximum refresh rate your monitor is capable of at the resolution your are 
using.  
Monitor Is 
Stuck In Active 
Off-Mode 
 The Computer Power Switch should be in the ON position.  
 The Computer Video Card should be snugly fitted in its slot.  
 Make sure the monitors video cable is properly connected to the computer.  
 Inspect the monitors video cable and make sure no pin is bent.  
 Make sure your computer is operational by hitting the CAPS LOCK key on the 
keyboard while observing the CAPS LOCK LED. The LED should either turn ON or 
OFF after hitting the CAPS LOCK key.  
Missing one of 
the primary 
colors (RED, 
GREEN, or 
BLUE) 
 Inspect the monitors video cable and make sure that no pin is damaged.  
 Make sure the monitors video cable is properly connected to the computer.  
Screen image is 
not centered or 
sized properly 
 Adjust H-Position and V-Position or press hot-key (AUTO).  
Picture has 
color defects 
(white does not 
 Adjust RGB color or select desired color temperature.  
 
						

							٢٧  | Page  
 
look white) 
Horizontal or 
vertical 
disturbances on 
the screen 
 Use Windows 95/98/2000/ME/XP shut-down mode Adjust CLOCK and FOCUS.  
 Press to auto-adjust.