AOC 2341va User Manual

							
 11
Adjusting Viewing Angle 
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitors angle to your 
own preference.   
Hold the stand so you will not topple the moni tor when you change the monitors angle.   
You are able to adjust the monitors angle from -5° to 20 °.   
 
 
NOTE: 
Do not touch the LCD screen when you change the a ngle. It may cause damage or break the LCD screen.
 
						

							
 12
Connecting the Monitor 
Cable Connections On Back of Monitor and Computer: 
 
 
   
To protect equipment, always turn off the PC and LCD monitor before connecting.   
 
1      Connect the power cable to the AC  port on the back of the monitor.   
2      Connect one end of the 15-pin D-Sub / 24-pin DVI cable to the back of the monitor and conn ect the other end to the 
computers D-Sub / DVI port.   
3      Connect one end of the USB cable to the back of the  monitor and connect the other end to the computers USB 
port.  
4    Turn on your monitor and computer.   
 
If your monitor displays an image, installation is comp lete. If it does not display an image, please refer 
Troubleshooting. 
1. Power  
4. USB 
2. DVI      
3. Analog (DB-15 VGA cable) 
 
						

							
 13
Wall Mounting 
Preparing to Install An Optional Wall Mounting Arm.    
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this 
procedure. Follow these steps: 
 
1     
2   Follow the manufacturers instructi ons to assemble the wall mounting arm.   
3      Place the wall mounting arm onto t he back of the monitor. Line up the holes of the arm with the holes in the 
back of the monitor.   
4      Insert the 4 screws into the holes and tighten.   
5      Reconnect the cables.    Refer to the users m anual that came with the optional wall mounting arm for 
instructions on attaching it to the wall.   
 
Noted :    VESA mounting screw holes are not available for  all models, please check with the dealer or official 
department of AOC.   
 
Remove the base and stand. 
 
						

							
 14
Adjusting 
Setting Optimal Resolution 
Windows Vista   
For Windows Vista: 
1 Click START.  
2 Click  CONTROL PANEL. 
 
 
3 Click  Appearance and Personalization.  
 
 
4 Click  Personalization   
 
 
 
						

							
 15
5 Click 
Display Settings.   
 
 
6 Set the resolution  SLIDE-BAR to 1920  by 1080.   
 
 
						

							
 16
Windows XP   
For Windows XP: 
1 Click START.   
 
 
2 Click  SETTINGS. 
 
3 Click  CONTROL PANEL.   
 
4 Click  Appearance and Themes.  
 
 
5 Double click  DISPLAY.  
 
 
 
						

							
 17
6 Click 
SETTINGS. 
 
7 Set the resolution  SLIDE-BAR to 
 
 
 
Windows ME/2000 
For Windows ME/2000: 
1 Click  START.   
2 Click  SETTINGS.   
3 Click  CONTROL PANEL.   
4 Double click  DISPLAY.  
5 Click  SETTINGS.   
6 Set the resolution  SLIDE-BAR to 1920 by 1080.   
1920 by 1080.   
 
						

							
 18
Hotkeys 
 
 
 
Power  
Press the Power button to turn 0n/off the monitor. 
 
Eco Mode / < 
Press the Eco key continuously to select the Eco m ode of brightness when there is no OSD ( Eco mode hot key 
may not be available in all models).   
 
4:3 or wide image ratio / > 
When there is no OSD, press  right hotkey continuously to c hange 4:3 or wide image ratio. (If the product screen size 
is 4:3 or input signal resolution is wide format, the hot key is disable to adjust. ) 
 
Auto /Source / Exit  
When the OSD is closed, press Auto button  will be auto configure hot key function .   
When the OSD is closed, press Source (or Auto/Source) butt on will be Source hot key function (Only for the models 
with dual or more inputs). Press Source button continuous ly to select the input source showed in the message bar , 
press Menu/Enter button to change to the source selected. Auto/Exit    Eco Mode/<    4:3 or wide/>   Menu/Enter    Power
 
						

							
 19
OSD Setting 
 
Basic and simple instruction on the control keys. 
 
 
 
 
1) Press the  MENU-button  to activate the OSD window.   
2) Press  < or > to navigate through the functions. Once t he desired function is highlighted, press the  MENU-button 
to activate sub-menu . Once the des ired function is highlighted, press MENU-button to activate it.   
3) Press  < or > to change the settings of the selected function. Press  < or > to select another function in sub-menu . 
Press  AUTO to exit . If you want to adjust an y other function, repeat steps 2-3.   
4) OSD Lock Function: To lock the OSD, press and hold the  MENU button while the monitor is off and then press 
power button  to turn the monitor on. To un-lock the OSD - press and hold the  MENU button while the monitor is 
off and then press  power button to turn the monitor on. 
 
Notes:  
1) If the product has only one signal input, the it em of Input Select is disable to adjust. 
2) If the product screen size is 4:3 or input signal resolution  is wide format, the item of Image Ratio is disable to 
adjust.    
3) One of DCR, Color Boost, and Picture Boost functions is  active, the other two function is turned off accordingly. 
 
						

							
 20
Luminance 
 Press Menu to display MENU Press   (Menu) to display menu. 
Press  or  to select  
(Luminance)
, and press to enter. 
Press  or   to select submenu, press 
to enter, and press  or  to 
adjust. 
Press  to exit.