Anthem Ltx 300 Lcos Projector Instructions

  
ENGLISH
21
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
  Connecting via SCART-RCA Cable
                                  
● Set lCOMP.z in the setting menu to lSCARTz.(P33 - 12 )
  Connecting via RGB Video Cable
   
● Set lCOMP.z
in the setting menu to lRGBz.(P33 - 12 )
● For information on compatible input signals, see lSpecifi cationsz. (P56)
HDMI 1HDMI 1HDMI 2HDMI 2S-VIDEOS-VIDEORS-232CY
RVIDEOVIDEOSYNCSYNCCB/PBCR/PRBG
This unit
To RGB video input terminalsRGB video...

2Preparation
22
 Installing the Projector and Screen
 
While installing, please place this unit and the screen perpendicular to\
 each other. Failing to do so may 
increase trapezoidal distortion. Please refer to 
lKeystonez. (P36 - 24 )
   SetAngle
 ● The angle range which can be set for this unit is ±10°.
  
 ● Malfunctions may occur if the angle is not set within the above-mentione\
d range.
 Shift Adjustment
                  
1 Installing the projector and screen
      ■ Left/Right position...

  
ENGLISH
23
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
2 Adjust such that the projected image is in the center of the screen
● It may be necessary to set lPixel Adjustz in the setting menu after adjusting the image position. (P36 - 22
 )
  Screen Size and Projection Distance
Determine the distance from the lens to the screen to achieve your desir\
ed screen size. 
This unit uses a 2.0x power zoom lens for projection. 
■
 Relationship Between Projection Screen Size and...

3Basic Operation
24
 Projecting Image 
This section describes the basic operations to project input images on t\
he screen.
 
Preparation
1 Insert the power plug to the power 
      outlet
2 Turn on the power
    
    
● You can also press the        button on the unit to turn on the power.
                 (
P15)
             

● The lens cover will be opened.
3 Project the image
     1
 Select input mode
                                        
 
● You can also select the input mode by pressing...

  
ENGLISH
25
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
       Adjust the image size (zoom)
● 
Every time the LENSLENS button is pressed, the adjustment item 
will be switched among “Focus”, “Zoom” and “Shift”. 
     )RFXV =RRP
6KLIWLENSLENS                    
    3
  To end
6  Turn off the power
     
● When power off, the lens cover will be closed.
● The power cannot be turned off within approximately 90 seconds
    after it has been turned on. Start operation only...

3Basic Operation
26
 
Convenient Features during Projection 
You can change the screen size of the projected image or hide the surroun\
ding area of an image for which 
quality at the outer area has deteriorated.
  Setting the Screen Size
The projected image can be set to a most appropriate screen size
(aspect ratio).
● The screen size can also be set from 
lAspect(Video)z of the setting menu.
      (
P34 - 14  )
● When PC signals are input, the 
lAspect(Computer)z setting will be available...

  
ENGLISH
27
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
2 Mask the image   
    
     
1  Display the setting menu
     
2  Select lInput Signal z
 lMaskz

     3
 Set a mask value
Example:
When the lMaskz value is 
changed from  lOffz 
 l5%z
3 To end  
MENU
MENUExitBACKBackSelectOperate
   0   0   0   06500K
2Normal
Picture ModeContrastBrightness
Color Tint
Color Temp.
Gamma
Advanced
Lens Aperture
 Picture Adjust
Natural
Reset
Video/S-Video COMP.AspectÄVideo Å...

4Settings
28
 Setting Menu 
Projected images can be adjusted to a desired view by changing the initi\
al settings.
Procedures for Menu Operation
Example: 
  When changing 
lAspect(Video)z
from l4:3z to l16:9z
1 Display the setting menu
2 Select lInput Signal z
 lAspect(Video)z
3  Set to l16:9z
4  To end
MENU
MENUExitBACKBackSelectOperate
   0   0   0   06500K
2Normal
Picture ModeContrastBrightness
Color Tint
Color Temp.
Gamma
Advanced
Lens Aperture
 Picture Adjust
Natural
Reset
4:3
4:3
16:9Zoom
ExitMENU...

  
ENGLISH
29
Getting StartedPreparationBasic Operation Troubleshooting
Settings Others
  Setting Menu
Item values shown in  are factory settings.
● Items that can be confi
 gured differ according to the input signals.
Picture Adjust 
01 Picture Mode
Adjusts the pattern of the projected image.
Cinema 1, Cinema 2, Natural, Stage, Dynamic, User 1, User 2 and User 3.
02 Contrast
Adjusts the contrast of the projected image.(Black) –50 to 50 (White)
03 Brightness
Adjusts the brightness of the projected image....

4Settings
30
Setting Menu (Continued)
Picture Adjust > Color Temp.
06 Color Temp.
Sets the color temperature of the projected image.
5800K Select this to give a reddish tinge to the 
image.
Only offset can be set.
6500K
Select this to have a balanced image.
7500K Select this to give a bluish tinge to the 
image.
9300K Select this to give a greater bluish tinge 
than 7500K.
High Bright Select this to get the brightest image.
Custom 1 Gain
(Bright part) Red
(Less red) –255 to 0 (More red)
Green (Less...