Anschutz Trigger Target Trigger 5020 User Manual
Here you can view all the pages of manual Anschutz Trigger Target Trigger 5020 User Manual. The Anschutz manuals for Small Bore Rifle are available online for free. You can easily download all the documents as PDF.
Page 1
26i
r
et uo
pa sd f
Trigger adjustments
1. Trigger weight
Adjust the trigger weight with set screw
No. 10 (silver screw):
¥if you turn it to the right:
trigger weight is increased (+)
¥if you turn it to the left: trigger weight is decreased (-)
Trigger weight and first stage weight
depend on each other with regard to the
mechanic mechanism. If one of them is
changed there will always be a corres-
ponding change of the other as well.
Trigger
Warning:
Your ANSCH†TZ target rifle offers you a...
Page 2
27
To move trigger cam No. 11:
¥lowest position of the trigger cam:
lowest trigger weight
¥highest position of the trigger cam:
highest trigger weight
If the trigger weight is to be more than 200 g,the trigger cam No. 11 must be adjusted
to the highest position (turn it by 180° and
fix it then). To do this you need a 2 mm hex
key and perhaps tweezers.
¥if you turn it to the left:
You release the screw
¥if you turn it to the right:
You tighten the screw
Attention:
Please ensure the trigger cam is...
Page 3
28 i retuo pa sd f The sear engagement is too long: There is a small distance between the second stage and the release of the trigger. ¥Turn set screw No. 5 clockwise after cocking and releasing (approximately 1/8 turn each). ¥Repeat this process until you do not feel the second stage anymore. Then turn 1/5 turn back to the left. Thus the optimum sear engagement is adjusted. The sear engagement is too short: There is no second stage. The trigger releases undefined without second stage. ¥Turn set screw...
Page 4
29
Attention:
The trigger stop set screw No. 8 can be
turned over the second stage or first stage
function. Malfunction (the trigger does not
release)!
6. Adjustment of the trigger blade
¥Loosen hex screw No. 7
¥Trigger blade No. 6 can be moved in the
longitudinal guide and can be tilted
laterally.
7. Change of two-stage trigger into
single stage trigger
Adjusting process:
¥Turn first stage weight screw No. 4 clock-
wise until you have reached the maximum
first stage.
¥Cock the rifle.
¥Turn set...
Page 5
30
Important note:
To protect your highly accurate trigger and
to maintain perfect functioning always
close the bolt carefully.
Attention:
If you change the trigger remove the bolt
from the receiver when fitting the trigger
as otherwise the trigger will be damaged.
i
ret uo
pa sd f
to the left until the cocking piston or firing
pin will release again.
The trigger does not catch the cocking
piston or firing pin:
¥Set screw No. 4 (first stage) is screwed in too much.
¥Check to see if the...
Page 6
1607, 1613, 1608 EDS1407, 1407 Z, 1409, 1411 1413, 1408 EDS1959 - 1974 1807, 1907, 1807 Z, 1907 Z 1907 Silh., 1807 Rep. 1907 Rep., 1907 Rep., 1912 1813, 1913, 1808 EDS 1808 D-RT, 1827, 1827F, 2007 2007/660, 2012, 2013 2013/690, 2013 Benchrest 54.18 MSR, 1808 MSR 2002 Compressed Air, 2020, 2025 1903, 1416 MSP, 1403 Rep. 64 MSR, 64 MPR, 64 R 2001 Superair 2001 D-RT Superair 2002 Superair 2002 D-RT Superair 700.65401407-U9l 150 gl 700.65411408-U1l 500 gl 700.65421408 D-U1l500 gl 700.65505071/1l 100 gl...