Anschutz LaserPower III Laser Rifle User Manual

11
7.3 Target box V 3.2
Power supply
Power can be supplied to the LaserPower target box in three different ways:
• External power supply (5  V operational voltage)
•  Lithium  batteries (2x1.5  V AA Lithium). Please use only Lithium batteries!
• PoE  (Power over Ethernet) – CAUTION: Max. cable length:   30 m!
The LaserPower Target box works in exactly the same way, no matter how it is 
supplied with power. You must be aware that, when operating using batteries, 
the Ethernet interface is not available...

12
Insert the batteries (depending on the modell**)
     Battery compartment [17] (on the back of the target box).
        Remove the battery compartment cover [23] (slotted hole rubber grommet).
Fig. 13 Battery compartment with cover on the LaserPower target box Fig. 14 Battery compartment cover
INSTRUCTION !
The battery must be removed for extended periods of 
non-use of the LaserPower target box in order to prevent 
damage caused by leaking or corroding of the battery.
INSTRUCTION !
The service life...

13
The operational states of the target box V 3.2
The LaserPower target box Version 3.2 has three different operating conditions:
• Ready for reception = On
• Standby =  Receiving power, but not switched on  
(in idle or power-save mode)
• Off = without batteries and disconnected from the mains (no power supply)
Ready for reception
The LaserPower target box Version 3.2 can be switched on in four different  
ways (= receive-ready mode):
• Switching on using the remote control (with power supply present)
•...

14
7.4 Power cable
Another way of supplying power to the 
LaserPower target is by using an external  
pluggable power unit [21]. The power unit  
can be used even when a battery is inserted.
 
The technical specifications of the 
power unit must satisfy the following 
requirements:
• Nominal voltage: 5 V; 1.0 A
• Voltage type: DC (observe following character:                  )
• Current capacity: 1,0  A
•   Plug connection: Coaxial power connector with  
(where possible injection moulded) plug
CAUTION...

15
•  The power unit will become hot while in operation. Ensure that it has  
sufficient ventilation.
•   Do not leave the power cable or the devices connected to it unattended  
during operation.
•   Pull the power unit out of the socket if the device has not been used for  
a longer period of time.
•   Unplug the device if it should suffer any fault in its functioning.
•   In order to remove the device fully from the mains, remove the  
power unit from the socket or the adapter from the device.
•...

16
8.1 Rear sight adjustment
The ANSCHÜTZ LaserPower III rear sight can be adjusted both vertically and 
horizontally.
Adjustment:
The target dot always depends on the setting of the rear sight [2]. 
Moving the rear sight [2] to the right causes the shot to be displaced to the right.
Moving the sight upwards causes the shot to be displaced upwards.
[2]
Fig. 19 Rear sight Fig. 
21 Rear sight adjustment
Fig. 22 Rear sight adjustment
Fig.  20 Removing the aperture screw
  Unscrew the aperture screw [x] to...

17
8.2 Target reducer
The target reducer [24] and the biathlon target [11] are equipped with  
Velcro stickers.
  In order to fix the target reducer on the biathlon target, push the target  
reducer onto the biathlon target with light pressure (the Velcro strips of  
both components must lie one on top of each other).
The target reducer can be quickly attached and removed as required.
8.3 Laser alignment
The laser is factory set to a range of 10 metres. Where other distances are being 
used, we...

18
9  Maintenance /  Cleaning
  The inside of the barrel of the LaserPower III rifle must always be free  
from dirt, dust, snow etc.
  A dry soft cloth should be used for cleaning the LaserPower III Set.
  With stubborn contamination the cloth can be slightly moistened and  
a mild cleaning agent can be used.
  The LaserPower III Set to be dried with a soft cloth.
CAUTION !
Material damage !
Damage to the product caused by chemicals.
   You must not use abrasive agents, scrubbing sponges,  
alcohol,...

19
12 TroubleshootingTroubleshooting
a.) The target fails to respond to shots:
  – Check power supply (high-performance Lithium battery and mains unit).
  – Switch on target.
  – Test functioning in darkened room.
  –   Isolate the power, wait one to two minutes, switch back on and  
observe the way the target areas light up.
  – Check that the rifle is working.
  – Check whether the target is in the correct LaserPower mode. 
  – Change over to mains unit operation.
b.)  Target areas very dark
  – With...

20
www.laserpower.net e.) The battery gets hot:
  – Remove the battery.
  – Remove the power supply.
  – Check for correct supply voltage.
  –  Send in if the fault repeats.
f.)  Smoke generation at the target box:
  – Remove the power supply as quickly as possible.
  – Send the target box to us immediately.
13 Description of stickers
[1]    Front view of the LaserPower target with view of the target areas and the infrared receiver 
(see Page 4).
[2]    Rear view of the LaserPower target with view of the...