Anschutz 2007, 2013 Instruction Manual

Bedienungsanleitung
Instruction Leaflet
KK-Matchgewehre
Small Bore Target Rifles
Mod. 2007 · 2013
Bitte sorgfältig lesen, bevor Sie
dieses Gewehr zusammenbauen
oder benutzen.
Please read carefully before you
assemble or operate this rifle.11/01
2007
2013 

2
Index
Prefa\fe ..................\h..................\h..................\h.... p.18 
\bafety instru\ftions ..................\h..................\h.... p.18 
General handling of rifles ..................\h......... p.19 
Ear and eye prote\ftion ..................\h.............. p.20
Laws ..................\h..................\h..................\h........ p.20 
Produ\ft relating safety instru\ftions ............. p.20 
Liability ..................\h..................\h..................\h.... p. 21...

18
Preface
Dear Friends of ANSCHÜTZ,
You  have  made  a  good  choice,  now  that
you  have  decided  to  buy  an  ANSCHÜTZ
product.  The  many  great  results  obtained
with ANSCHÜTZ rifles by target shooters,
participants in the Olympic Games as well
as in World and European championships
made  your  choice  easy,  as  your  rifle  has
benefited  from  our  great  experience  of
making fine sporting and target rifles since
1856.  World-wide,  ANSCHÜTZ  rifles  are
respected  because  of  their  fine...

19
General handling of rifles
1. Treat every rifle as though it was loaded.
Do not take anyone’s word or automatically
assume  it  is  not  loaded.  Check  your  rifle
personally each time you handle it. The safe
and  courteous  way  to  carry  a  rifle  when
you are with others is to leave the bolt open
so  that  they  can  easily  see  that  the  rifle
cannot be fired. Make sure that the rifle is
not loaded when you stop shooting. Make
sure  your  rifle  is  unloaded  before  every
transport. Never...

20
Ear and eye protection
You and other persons should always use
approved hearing protection and approved
shatterproof eye protection while shooting.
Laws
When  using  a  rifle  observe  the  corres-
ponding  regulations  and  laws  for  the  use
of firearms in your country. by  an  authorized  gunsmith.  Unqualified
handling or disassembly can cause injuries
or irreparable damage of the rifle.
9. Your rifle should always be handled with
extreme  care.  Make  sure  that  it  is  never
dropped  or...

21
Liability
1.  ANSCHÜTZ  does  not  assume  any
responsibility or payment of damage claims
for damages of any kind resulting from the
disregard of these instructions, non-qualified
treatment or repair, the use of non-original
ANSCHÜTZ  spare  parts,  incorrect
handling, negligence, removal of the knot
varnish or unauthorized modifications.
2. The stock of this rifle has been very care-
fully checked by factory inspectors prior to
shipment  and  has  been  determined  to  be
free of defects. Certain...

22
Fitting the barrel
The screws for fixing the barrel must not be
loosened.  Should  it  be  necessary  to
Assembly, fitting the
ANSCHÜTZ barreled action
The stock, the barreled action and the bolt
are  packed  separately  for  shipment  and
need to be assembled. However, do not do
this  until  you  have  followed  all  the
procedures listed below.
•Wipe away excess oil from the barreled
action and the bolt.
•Insert  the  cocked  bolt  (also  see  chapter„Disassemble  the  bolt“).  The  bolt  is
cocked...

23
Unloading
For safety reasons the rifle must immediately
be unloaded if you intend to stop shooting.
Unlock  and  open  the  bolt.  This  will  eject
the  cartridge.  Please  also  see  safety
instructions  for  the  handling  of  rifles  and
pistols.
Cocking, loading and safety
operation
•Degrease the bolt and the interior of the
barrel without leaving lint.
•Open the bolt and pull it back to the stop.
Carefully  insert  an  approved  cartridge
with the bullet forward with the thumb into
the chamber....

24
Trigger
Warning:
Your  ANSCHÜTZ  target  rifle  offers  you  a
versatility of individual adjusting properties.
Please  make  sure  that  your  rifle  always  is
unloaded when carrying out adjustments. the bolt body. Turn the bolt handle until
the cocking cam is in line with the slot at
the end of the bolt body.
•Insert the complete firing pin with spring
and spring support with the pin first into
the  bolt  body  and  ensure  that  its  lug
penetrates the longitudinal slot.
•Attach  the  cover  sleeve...

25
To move trigger cam No. 11:
•lowest position of the trigger cam:
lowest trigger weight
•highest position of the trigger cam:
highest trigger weight
If the trigger weight is to be more than 200 g,
the trigger cam No. 11 must be adjusted to
the highest position (turn it by 180° and fix
it  then).  To  do  this  you  need  a  2  mm  hex
key and perhaps tweezers.
•if you turn it to the left:
You release the screw
•if you turn it to the right:
You tighten the screw
Attention:
Please ensure the trigger cam...