Anetsberger Brothers I12 Cooking Computer Ops Manual

							  
L20-381 Rev 0 (12/23) 
English 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
This control was developed specifically for ANETS fryer products.  It utilizes the latest in 
microprocessor technology and is completely solid state.  This control offers the latest cooking 
technology, including temperature and time compensation that requires no user adjustments for 
consistently cooked product.  Other features include, drain valve interlock, faulty probe detection, 
selectable melt cycles, beeper volume, and cook temperature.  Each product key may be programmed 
with cook, shake and hold times to keep pace with changing menus over time. 
 
This manual details the operation and adjustment of the ANETS I12 Cooking Computer control.  The 
target audience for this text is the Service Technician.  This manual reveals all adjustments that are 
possible by keyboard entry, including passwords. 
IMPORTANT INFORMATION FOR FUTURE REFERENCE 
Record  the following information from the appliance ID plate 
and retain this manual for the life of the equipment:
 
Model #:   __________________________   
Serial #:   __________________________   
Date Purchased:   ___________________   
Operations Manual 
for ANETS P/N 60149509 Single Vat 
I12 Cooking Computer  
						

							ANETS I12 Cooking Computer 
ANETS P/N 60149509 
L20-381 Rev 0                                          Page 2 of 12 
Table of Contents: 
 
1 Key Locations and Functions: ..........................................................................................................  3 
1.1 To turn the appliance ON:  _______________________________________________________ 3 
1.2 To turn the appliance OFF: _______________________________________________________ 3 
1.3 To start a cook: ________________________________________________________________ 3 
1.4 To cancel a cook: ______________________________________________________________ 4 
1.5 To check Actual and Set temperatures: _____________________________________________ 4 
1.6 To View Current Settings for Cook, Shake, Hold, and Hold Pre-Alarm: _____________________ 4 
1.7 To perform a Boil Out operation:  __________________________________________________ 5 1.7.1 Automatic Boil Entry (Water Detection): ......................................................................................................................... 5 1.7.2 Manual Boil Entry: .......................................................................................................................................................... 5 
2 To Enter Programming Level 1 (for the Store Manager): ............................................................... 6 
2.1 To Set Cook Temperature: _______________________________________________________ 6 
2.2 To Change a Product Key–Cook, Shake, Hold, and Hold Pre-Alarm Times: _________________ 7 2.2.1 Cook Time ...................................................................................................................................................................... 7 2.2.2 Shake Time .................................................................................................................................................................... 7 2.2.3 Hold Time ....................................................................................................................................................................... 7 2.2.4 Hold Pre-Alarm ............................................................................................................................................................... 8 
2.3 To Exit Level 1 programming: _____________________________________________________ 8 
3 To Change Options Level 2 ( for the Store Manager): ....................................................................  9 
3.1 Fahrenheit or Celsius Display:  ____________________________________________________ 9 
3.2 Password Change or Required?  __________________________________________________ 9 
3.3 Beeper Volume and Tone: ______________________________________________________ 10 
3.4 Language Selection: ___________________________________________________________ 10 
3.5 Melt Cycle Type: ______________________________________________________________ 10 
3.6 Recovery Test Value: __________________________________________________________ 11 
3.7 Control or Timer: (Left side of Dual or Single Vat)  ____________________________________ 11 
  
						

							ANETS I12 Cooking Computer 
ANETS P/N 60149509 
  Page 3 of 12  L20-381 Rev 0 
 
1  Key Locations and Functions: 
 
1.1  To turn the appliance ON: 
If power is applied to the appliance, the displays will show .  Press the  key.  
Displays will show one of the following:  
; , or .  Some messages may show in both left 
and right displays.  Wait for the appliance to heat up to the [READY] condition before cooking. 
 
1.2  To turn the appliance OFF: 
Press the  key. Display will momentarily show the software version number ,  
and then 
. 
 
1.3  To start a cook: 
When the display is showing  the appliance has reached set 
temperature and is ready to cook.  Press the desired product key, and place 
product into the vat.  The indicator above the product key will flash to indicate the 
cook timer is running.  In the example above, product 4 is cooking with 2 minutes 
and 28 seconds remaining.  The right side display of the dual vat control shown 
above, has no running cook timers, and shows 
. 
Multiple cooks may run together.  While cooks are running, the displays will 
always show the cook with the least time remaining.  Longer running cooks will 
flash their indicators at a slower rate.  Cook time remaining on these keys may be 
checked by pressing the 
 key then pressing a product key. 
  
 
 
 
  
						

							ANETS I12 Cooking Computer 
ANETS P/N 60149509 
L20-381 Rev 0                                          Page 4 of 12 
1.4  To cancel a cook: 
Press and hold the product key to cancel a running cook.  If no other cooks are 
pending, controller displays will return to 
. 
  
1.5  To check Actual and Set temperatures: 
To view the actual vat temperature, press the  key.  The display will show  
or 
, where “F’ is Fahrenheit, and “C” is Celsius.  After a few moments, the display  
will return to 
; , or ,if no cooks are running.  [CKn 
mm:ss] will display for any cooks still running. 
To view the set temperature, press the 
 key twice. The display will show  
or 
, where “F’ is Fahrenheit, and “C” is Celsius.  After a few moments, the display  
will return to 
; , or ,or,  [CKn mm:ss] for any cook 
still running. 
 
1.6  To View Current Settings for Cook, Shake, Hold, and Hold Pre-Alarm: 
To view the current settings for any product key, press the  key, followed by the desired 
product key.  The display will show [CKn mm:ss], followed by [SHn mm:ss], then [HDn mm:ss], 
ending with [PA4 mm:ss].   Where “n” is the key number, and “mm:ss” is the time setting.  
After a few moments, the display will return to 
; , or 
, or,  [CKn mm:ss] for any cook still running. 
 
Typical displays using key 4 as an example: 
Key 1 Cook Time [C1] is set for 3 minutes and 28 
seconds. 
Key 1 Shake Time [S1] is set for 2 minutes and :00 
seconds before the end of the Cook.  Default value is 
00:00, or inactive. 
Key 1 Hold Time [H1] is set for 15:00 minutes.  This is the 
amount of time cooked product may sit in holding bins 
before a new batch is started.  Default value is 00:00, or 
inactive. 
Key 1 Hold Pre-Alarm [P1] is set for 00:00 and is inactive 
(default setting).  When activated his alarm warns the 
operators that the Hold Time is about to run out.   
In a few moments, the display will return to 
. 
  +    
						

							ANETS I12 Cooking Computer Service 
ANETS P/N 60149509 
 
  Page 5 of 12  L20-381 Rev 0 
12 2
00 1
1.7  To perform a Boil Out operation: 
Normal maintenance of a fryer requires regular tank cleaning.  This process involves draining the 
vat of oil and filling with water.  Cleaning solution is added, and the control is set to boil by one of 
the following methods: 
 
1.7.1  Automatic Boil Entry (Water Detection): 
Fill the appliance with water and turn the appliance on.  Heat will be applied to the vat warming 
the water.  This control will detect the presence of water by temperatures not rising above the 
boiling point of water; 212°F (100°C).  After a time at this temperature, displays will show 
  
Heat will be disabled until the operator responds to this prompt.  Pressing the [0] key is a YES 
response to the boil prompt.  If pressed, display will show . Heat will maintain 
vat temperature at 185°F (85°C) for cleaning as long as the control remains on.  To exit boil 
mode control must be turned off. 
 
Warning: Pressing any other key at the 
 prompt is regarded 
by the control as a NO response.  With this response, the control will apply heat to the vat as if 
oil were present in the vat. With water in the vat, a rolling boil will result. This will cause 
undesirable foam over conditions.  And, a potential steam burn hazards to operators 
performing cleaning operations. 
 
1.7.2 Manual Boil Entry: 
After filling an empty vat with water, turn the appliance on.  Press the 
 key and enter key sequence [2], [1], [2].  If control is set to 
display in the Celsius scale, press [1], [0], [0] keys to manually enter boil 
mode.  The display will show 
 to indicate entry into boil 
mode.  
To exit boil mode, control must be turned off.  
						

							ANETS I12 Cooking Computer 
ANETS P/N 60149509 
L20-381 Rev 0  Page 6 of 12 
 
2  To Enter Programming Level 1 (for the Store Manager): 
Note: The factory default setting for this control does not require a  password to be entered.  
However, the operator password requirement and value may be changed in section 3.2.  
Entry of a password when NOT required will not interfere with the programming process. 
With no cook timers running, displays will show one of the following displays: 
; 
, or .  Press the  key. 
If display shows:  
, a password is required.
  
Enter password 
 using the product keys 
as a numeric keypad for entry.  With correct password entry, 
display will show 
.   
If display shows: 
; you do not need 
to enter a password. 
 
 
 
 
 
From the 
 display, continue with this section or  
go to section 3, or 4. 
 
2.1  To Set Cook Temperature: 
 Press the  key once.   The display will show [SET xxxF] [TEMP] or [SET xxxC] 
[TEMP], where “xxx” is the temperature setting.   
 Use the product keys for numeric entry to adjust the current setting.  Press the  key 
to save setting.   
 Display now shows .  To exit here, press  again, or continue. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							ANETS I12 Cooking Computer 
ANETS P/N 60149509 
                                                              Page 7 of 12  L20-381 Rev 0    
2.2  To Change a Product Key–Cook, Shake, Hold, and Hold Pre-Alarm Times: 
For each product key, Cook, Shake, Hold, and Hold Pre-alarm times are set in this section.   
With display showing 
, continue with the following section for each product key to 
change. 
 
2.2.1 Cook Time 
Cook Time may be set for each product key.  To deactivate any product key enter a zero value 
for cook time.   
 Press the  key.   
 Display will show .  Press the desired product key to 
change.   
 Display shows [nCK mm:ss] [TIME] where “n” is the key number, “CK” means Cook, and 
“mm:ss” is minutes and seconds.   
 Use the product keys for numeric entry to adjust the current setting.  Press the  key to 
save cook time and continue setup for this product key. 
 
2.2.2 Shake Time 
Shake time is an alarm that sounds during Cook Time to prompt operators to shake the basket.  
Default for this value is zero, meaning the Shake Time is inactive. To use Shake Time, the time 
value must be a non-zero value, and, must be set to a value less than cook time. 
 
 Display shows [nSH mm:ss] [TIME] where “n” is the key number, “SH” means Shake, and 
“mm:ss” is time in  minutes and seconds. 
 Use the product keys for numeric entry to adjust the current setting.  Press the  key to 
save shake time and continue setup for this product key. 
 
Note: The value entered for shake time is the time from the end of the cook. 
 
2.2.3 Hold Time 
Cooked product may stand in holding bins for a period of time.  This timer produces an alarm to 
inform operators to discard old product and start a new cook. Default for this value is zero, 
meaning the Hold Time is inactive. 
 
 Display shows [nHD mm:ss] [TIME], where “n” is the key number, “HD means HOLD, 
and “mm:ss” is minutes and seconds.   
 Use the product keys for numeric entry to adjust the current setting.  Press the  
key to save hold time and continue setup for this product key. 
 
 
 
  
						

							ANETS I12 Cooking Computer 
ANETS P/N 60149509 
L20-381 Rev 0     Page 8 of 12     
2.2.4 Hold Pre-Alarm 
Hold Pre-Alarm is a timer setting that is used to warn operators that the Hold Time is about to 
expire.  To use Hold Pre-Alarm, the time value must be a non-zero value, and, must be set to a 
value less than Hold Time.  Default value is zero, meaning the Hold Pre-Alarm is inactive. 
 
 Display shows [nPA mm:ss] [TIME] where “n” is the key number, PA means Pre-Alarm, 
and “mm:ss” is minutes and seconds. 
 Use the product keys for numeric entry to adjust the current setting.  Press the  
key to save pre-alarm time.  
 
Note: Value entered for hold pre-alarm time is the time from the end of the hold period. 
 
Display will again return to 
.  Repeat steps from section 2.2.2 
to make changes to any other product keys or continue with section 2.3. 
 
2.3  To Exit Level 1 programming: 
 
Display shows 
.  
 Press the  key.  Display shows .  Continue to section 3 “To Change 
Options”, or, exit here in the next step.   
 To exit Level 1 programming, press the  key again.   
Displays will show 
; , or , when no active cooks 
are running. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							ANETS I12 Cooking Computer 
ANETS P/N 60149509 
                                                              Page 9 of 12  L20-381 Rev 0    
1
2
0
 
3  To Change Options Level 2 ( for the Store Manager): 
The display must show  from section 2 to change these options. When the  
product key [10/0] is pressed, the display will show 
.  Indicator 
lights above product keys will illuminate to represent options that may be changed.  Each option 
listed below uses the product key [0] to toggle or scroll through available choices in the display.  
When the correct value is displayed, press the 
 key to save choice.  The display will again return 
to 
 for another option selection. 
 
3.1  Fahrenheit or Celsius Display: 
The Controller will display temperatures in the Fahrenheit or Celsius scales. The default scale is °F.  
With display showing 
, press the product key [0]. 
 
 Display shows . 
 
 Press product key 1, display shows [DEGREE n] [F OR C], where “n” is the current 
setting.   
 Use the product key [0] to scroll through choices (F or C).   
 Press  key to save choice. Display now shows . 
 
3.2  Password Change or Required? 
With factory settings, an operator password is not required to enter programming Levels 1 and 2.  
The password may be activated or changed in these steps. 
With display showing 
, press the product key [0].   
 
 Display will show . 
 
 Press product key 2, display shows [SET PAS] [NEW PASS]. Use the product key [0] to 
scroll through choices [NO PASS] or [PASS REQ].  Press 
 key to save choice.   
 If [NO PASS] is selected Display returns to . 
 
 If [PASS REQ]. is selected, display will show [PASSnnnn] [NEW PASS] to prompt for new 
password.  Displayed value “nnnn” is the current password. Use the product keys for numeric 
entry to change password.   
 
 Press               key to save choice.  Display then shows . 
 
Note:  The factory default password (6684) will always work even if a different password is selected 
here.  
						

							ANETS I12 Cooking Computer 
ANETS P/N 60149509 
L20-381 Rev 0     Page 10 of 12     
3.3  Beeper Volume and Tone: 
Volume and Tone of the beeper alarm may be changed in this section.  Volume ranges are 1,2 and 
3, where 3 is the loudest setting.  This model also has a selection for tone. 
With display showing 
, press the product key [0]. 
 
 Display will show .  Press product key 3, display  
shows [VOLUME n] [BEEPER].   
 
 Use the product key [0] to scroll through choices (n= 1,2,3, or T).  Beeper volume will  
change as each selection is made. 
 
 If “T” is selected an additional display is shown, [TONE n] [BEEPER]. Use the product key [0] to 
scroll through choices (n= 1,2,3). Beeper tone will change as each selection is made. 
 Press 
 key to save choice.  Display shows 
. 
 
3.4 Language Selection: 
With display showing , press the product key [0]. 
 Display will show . 
 
 Press product key 4, display shows [ENGLISH] [LANGUAGE]. 
 
 Use the product key [0] to scroll through choices (ENGLISH, ESPANOL, FRANCAIS,  
DEUTSCH, HOLLAND). 
 Press 
 key to save choice.  Display shows 
. 
 
3.5  Melt Cycle Type: 
This adjustment allows selection of the melt cycle type and requirement when starting the appliance 
from a cold start. 
With display showing 
, press the product key [0]. 
 
 Display will show . 
 
 Press product key 5, display shows [LIQUID], the default setting. 
 
 Use the product key [0] to scroll through choices (liquid, solid, or, no melt). 
 Press 
 key to save choice.  Display will again return to 
.