Anetsberger Brothers Griddle SGC Models 34 Chrome gas griddle User Manual

							11
GRILL  GRILL GRILL  GRILL 
GRILL
TR TRTR TR
TR
OUBLESHOO OUBLESHOOOUBLESHOO OUBLESHOO
OUBLESHOO
TING GUIDE  TING GUIDE TING GUIDE  TING GUIDE 
TING GUIDE (Continued)
1. Check that gas control valve is set to
“ON”.
2. Check that pilots are burning.
3. Increase temperature setting on
thermostat control.
4. Check gas supply pressure with all other
equipment operating. (6” WC for natural
gas and 11” WC for propane, minimum)
5.  Observe if main burners ignite.1. Yes - Proceed to test #2.
No - Turn to “ON” and skip to
test #5.
2. Yes - Proceed to test #3
No - Follow lighting instructions
on page 7.  Skip to test #5.
3. Proceed to test #4.
4. Increase if needed, proceed to
    test #5.
5. Yes - Okay.
No - Replace gas control valve.
PROBLEM CAUSE REMEDY
1.  Turn thermostat control to “OFF”.
Observe if main burners go off.
2.  Turn gas control valve knob to “OFF”.
Observe if main burners go off.
3.  Reset thermostat control to desired
setting.  Observe if main burners go off
when temperature is reached.1. Yes - Skip to test #3.
No - Proceed with test #2.
2. Yes - Proceed with test #3.
No - Replace gas control
    valve.
3. Yes - Okay.
No - Replace thermostat.
Main burners do not
ignite.
Over temperature or
main burners do not
stop burning.
Grill plate is cold
(Burners not
firing).1. Check that gas supply is turned on.
2. Check for lit pilot.
3. Check that gas control valve is in “ON”
position.
4. Check that thermostat control is at
desired setting.1.  Yes – Proceed to test #2.
     No – Turn on, follow
     Lighting Instructions on
     page 7. Skip to test #4.
2.  Yes – Proceed to test #3
     No – Follow Lighting
     Instructions on page 7.  Skip
     to test #6.
3.  Yes – Proceed to test #4.
     No – Turn to “ON”.  Skip to
     test #6.
4.  Yes – Proceed to test #5.
     No – Increase setting.
     Proceed to test #5.
L20-346 Rev3 
						

							12
GRILL  GRILL GRILL  GRILL 
GRILL
TR TRTR TR
TR
OUBLESHOO OUBLESHOOOUBLESHOO OUBLESHOO
OUBLESHOO
TING GUIDE  TING GUIDE TING GUIDE  TING GUIDE 
TING GUIDE (Continued)
PROBLEM CAUSE REMEDY
Grill plate is not hot
enough.1. Check that thermostat control
setting is at desired setting.
2. Check gas supply pressure with all
other equipment operating. (6”
WC for natural gas and 11” WC
for propane, minimum).
3. Check for fans or excessive air
flow over grill surface.
4. Check for dirty/sooty pilot burner.
5. Observe if grill plate temperature
is acceptable.1.  Yes – Proceed to test #2.
     No – Increase setting.  Skip to
     test #5.
2.  Above – Proceed to test #3.
     Below – Increase gas supply
     pressure.  Skip to test #5.
3.  Yes – Block or turn off air supply.
      Skip to test #5.
      No –P proceed to test #4.
4.  Yes – Clean pilot burner.
     Proceed to test #5.
     No – proceed to test #5.
5.  Yes – Okay.
      No – Replace thermostat.
Black soot accumu-
lation on burners on
under side of grill
plate.1. Check if pressure regulator is
installed in supply line.
2. Adjust pressure regulator setting by
turning the adjusting slot counter-
clockwise (under the slotted cap).1.  Yes – Proceed to test #2
     No – Install regulator supplied
     with  unit.  Proceed to test #2. 5.  Check gas supply pressure with all
      other equipment operating. (6”
    WC for natural gas and 11” WC
     for propane, minimum).
6.  Observe if main burners are firing.5.  Increase if needed, proceed to
     test #6.
6.  Yes - Okay.
     No - Replace thermostat. (Continued)
Grill plate is cold
(Burners not
firing).
L20-346 Rev3 
						

							














































ORIGINAL EQUIPMENT LIMITED WARRANTY 
General Warranty Anets, Inc. warrants to the original user of its commercial cooking appliances and related equipment that said appliances and related equipment will be free from 
defects 
in material and workmanship under normal use for a period of one (1) year from the date of installation, with appropriate documentation, to a maximum of 
fifteen (15) months from the date of manufacture, subject to the following additions, exceptions, exclusions and limitations. 
What is covered 
This warranty is limited to the repair or replacement at the Company’s option, without charge, of any part found to be defective within the warranty period and 
reasonable 
expenses incurred for freight and material for the installation of such part; in addition, the Company’s obligation shall be limited to reimbursement for normal 
labor on such parts. 
Anets, Inc. agrees to pay the Authorized Service and Parts Distributor, for any labor and material required to repair or replace, at the Company’s option, any part 
which 
may fail due to defects in material or workmanship during the above general warranty period. 
Silver Line Fryers In addition to the above general warranty, for its economy fryers and cookers, the Company warrants to the original user any mild.
 Stainless steel fry tank or cooking 
vessel to be free from defects for a period of one (1) year, 
from the date of manufacture.  Labor and freight shall be the responsibility of the end user. 
Gold Line Fryers 
In addition to the above general warranty, for its standard fryers and cookers, the Company warrants to the original user any stainless steel fry tank or cooking 
vessel to be free from defects for a period of (1) year parts and labor and 10 year Frypot or cooking vessel Part only from the date of manufacture Labor and 
freight shall be the responsibility of the end user. 
Pasta Cooker
In addition to the above general warranty, for its standard fryers and cookers, the Company warrants to the original user any stainless steel fry tank or cooking 
vessel to be free from defects for a period of one (1) year parts and labor and 5 years Frypot or cooking vessel part only after year one from the date of 
manufacture.  Labor and freight shall be the responsibility of the end user. 
Limitations to Fry Tank and Cooking Vessel Warranty After the expiration of the general warranty period, any additional warranty on fry tanks or cooking vessels shall only obligate the Company to repair or replace, at 
its
option, any fry tank or cooking vessel which it determines to be defective.  Claims under this item shall be supported by a statement detailing the defect, and the 
Company 
may require the return of the fry tank or cooking vessel claimed to be defective.  Labor and freight shall be the responsibility of the end user. 
How to Keep Your Warranty in Force  Make sure any shipping  damages are reported immediately.Damages of this nature are the responsibility of the carrier and must be reported by the receiver. 
 Install the unit properly
.This is the responsibility of the installer and the procedures are outlined in the manual. Do not install it in a home or residence.  Maintain it properly. This is the responsibility of the user of the appliance and the procedures are outlined in the manual. 
 Adjustments, such as calibration, leveling, tightening of fasteners or plumbing or electrical connections normally associated with initial installation. These
procedures are outlined in the manual and are NOT covered by warranty. 
If it is damaged due to flood, fire or other acts of God, this is not covered under this warranty. 
Use it for what it is intended.If it is used for a purpose other than for which it was intended or designed, resulting damages are not covered under the    
  warranty. 
 Make sure that it has the correct voltage, gas supply and/or good quality water
.If a failure is due to poor water quality, harsh chemical action, erratic 
voltage or gas supplies, these damages are not covered under the warranty. 
 Do not materially alter or modify from the condition in which it left the factory. 

Do not obliterate, remove or alter the serial number rating plate.  Use only Genuine OEM parts from Anets, Inc.or its Authorized Parts and Service Distributors.Repairs are not covered by the warranty. 

If any other failure occurs which is not attributable to a defect in materials or workmanship, it is not covered. 
This warranty specifically excludes parts which wear or would be replaced under normal usage, including, but not limited to, electric lamps, fuses, interior or 
exterior finishes, o-rings and gaskets. 
Limits to the Warranty 
Outside the United States of America and Canada, this warranty is limited to the replacement of parts and Anets, Inc. will not bear any other expense be it   
labor,mileage, freight or travel. 
If any oral statements have been made regarding the appliance, these statements do not constitute warranties and are not part of the contract of sale. This 
limited
warranty constitutes the complete, final and exclusive statement with regard to warranties. 
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES WHETHER WRITTEN, ORAL OR IMPLIED, INCLUDING, BUT  
NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR WARRANTY AGAINST LATENT DEFECTS. 
Limitations of LiabilityIn the event of a warranty or other claim, the sole obligation of Anets, Inc. will be the repair or replacement, at the Company’s option, of the appliance or the 
component part. This repair or replacement will be at the expense of Anets, Inc. except as limited by this warranty statement. Any repair or replacement under this 
warranty  does  not  constitute an extension in time to the original warranty. Parts covered under this warranty will be repaired or replaced, at the Company’s option, with new or 
functionally operative parts. The liability of Anets, Inc. on any claim of any kind, including claims based on warranty, express or implied contract, negligence, strict liability or 
any other legal theories will be exclusively the repair or replacement of the appliance
.This liability will not include, and the purchaser specifically renounces any right to 
recover  special,  incidental, consequential or other damages of any kind, including, but not limited to, injuries to persons, damage to property, loss of profits or anticipated 
loss of the use of this appliance. 
If any provision of this warranty is unenforceable under the law of any jurisdiction, that provision only will be inapplicable there, and the remainder of the warranty 
will remain unaffected
.The maximum exclusion or limitation allowed by law will be substituted for the unenforceable provision. 
How to Obtain Warranty Service 
First direct your claim to the Anets, Inc.Authorized Service and Parts Distributor closest to you giving complete model, serial and code numbers, voltage, gas 
type, 
and description of the problem.Proof of the date of installation and/or the sales slip may also be required.If this procedure fails to be satisfactory, write the 
National Service Manager, Anets, Inc., P.O.Box 501, Concord, NH.03302-0501.USA
This warranty gives you certain specific legal rights; you may have other rights which vary from state to state. 
Anets,Inc.,	




	

	
 !

#$ 
%&()
*	))+,()
*	www.ANETS.com
L14022R1PrintedinU.S.A. 
						

							
In the event of problems with or questions 
about your order, please contact the Anets 
factory at: 
(603)-225-6684 World Wide  
Website Address: www.anets.comIn the event of problems with or questions about 
your equipment, please contact the Anets 
Authorized Service and Parts representative 
(ASAP) covering your area, or contact Anets 
at the numberlisted to the left. 
MAILING ADDRESS – P.O. BOX 501, CONCORD, NH  03302-0501 
SHIPPING ADDRESS – 10 FERRY STREET, CONCORD, NH  03301 
L20-346 Rev3