Home > Anetsberger Brothers > Fryer > Anetsberger Brothers Filtration System FFM80FFM150 Portable filters available in 80 lb or 150 lb shortening capacities User Manual

Anetsberger Brothers Filtration System FFM80FFM150 Portable filters available in 80 lb or 150 lb shortening capacities User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Anetsberger Brothers Filtration System FFM80FFM150 Portable filters available in 80 lb or 150 lb shortening capacities User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 50 Anetsberger Brothers manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							URCUL
    Anets ~ Dependable Foodservice Equipment 
                     PO Box 501 Concord, NH  03302 
            Tel: 603-225-6684  Fax: 603-228-5231 
     
     
     
    Portable Filter Systems 
    Models 
    FFM-80 
    FFM-150 
     
    Installation, 
    User Operation, 
    & 
    Maintenance 
    Manual 
     
    DANGER 
    Improper installation, adjustment, alteration, service, or maintenance can 
    cause property damage, injury or death. Read the installation, operating 
    and maintenance instructions thoroughly before installing or servicing this 
    equipment. 
     
     
     
     
     
     
     
     
     
     
            Keep this Manual in a Convenient Location for Reference
     
     
    The Anets GoldenLine 
    Quality Equipment For The Restaurant, Supermarket, and Bakery Industries 
     
    L20-344 Rev 2
    Model FFM80 shown
    ! 
    						
    							TABLE OF CONTENTS 
     
    Shipping Container Inspection....................................................... 2 
    Code Requirements ......................................................................  4 
    Filter Unit Preparation Instructions 
    ................................................ 4 
    Filter Diagrams .............................................................................. 5  
    Filtering Instructions ...................................................................... 6 
    Oil Disposal Instructions ...............................................................  7 
    Replacing The Filter Paper............................................................  8 
    Filter Troubleshooting Guide .......................................................... 9  
    Filter Warranty .............................................................................. 9 
    Parts Diagram .............................................................................. 1 1  
    Parts List ..................................................................................... 1 2  
     
     
     
     
     
     
     
     
     
    SHIPPING CONT AINER INSPECTION 
    1.  Carefully examine the shipping container for external damage.  When damage is noted, notify the 
    delivery carrier immediately. Save all packing materials for damage claim examination. 
    2.  If no external damage is noted, remove the shipping container from the filter and examine the unit 
    carefully for damage.  Place the filter in a safe location, if damage is noted, so that the freight 
    damage claims adjuster can examine it. 
     
         Models Co vered By  This Manual 
    FFM-80 Portable Filter System - 80 lb. capacity 
    FFM-150 
    Portable Filter System - 150 lb. capacity 
     
     
    Standard Accessories  furnished in the shipping carton with this filter include: 
     
     
     
     
     
     
    NOTE:  A Parts List for each Anets Filter System is among the items shipped with each unit. If an 
    additional copy of this list is needed, please contact the factory as directed on the back cover. 
     
    L20-344 Rev 2
    ! DAN G ER 
    Read these specifications, Code Requirements, Installation Requirements, 
     Installa
    tion Instructions, and Operating Instructions very carefully. Failure to follow 
    the Instructions could cause the filter system to malfunction
    . A filter system malfunction 
    can result
     in property damage, serious bodily injury, or death. 
    (1) Filter Screen Assembly 
    (2)  Starter Paper Starter Pack 
    (3) Return Hose Assembly 
    2 
    						
    							NOTES 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    L20-344 Rev 23  
    						
    							               INSTALLATION INSTRUCTIONS 
    FILTER ELECTRICAL  SPECIFICATIONS 
    Please make sure that your desired filter location has electrical supply factors that are suitable for this 
    product line.  Requirements are120 Volts, 60 Hz, 8 Amps, 1-phase, three wire connection, 
    including an electrical ground. This unit is not fused.  Protect circuit with proper sized fuses or 
    circuit breaker line 
    disconnect switch, circuit breaker, or plug and receptacle of power cord 
    connection should be readily
     accessible to the operator. 
     
     
    Electrical Grounding Instructions 
     
    This appliance is equipped with a three-prong (grounding) plug for 
    your protection against shock hazard, and should be plugged
     
    directly into a properly grounded, three-prong receptacle. DO NOT 
    cut or remove the grounding prong from this plug. 
     
     
    FILTER UNIT PREPARATION (Refer to Photos On Page 4) 
    1.  Assemble filter envelope to filter screen by sliding the envelope over the filter screen, folding 
    back the open end over the filter screen.  Make sure the hole in the filter envelope fits over 
    the fitting on the filter screen. 
    WARNING 
    Only use filter paper envelopes from Anets that have been specifically 
    designed for this filter system
    . Using the wrong type of filter paper can cause 
    damage to the pump system, and will void the Warranty 
     
     
    2.  Assemble filter envelope clip over folded back end of envelope and over fitting on filter 
    screen. 
    3.  Attach knurled retaining nut onto fitting on screen, securing the assembly 
    4
    . Attach quick-connect coupling located on drain tube to knurled retaining nut. 
    5.  Place filter unit into the filter tank. 
    6. Connect the filter assembly to the pump using the quick-connect assembly 
    7.  Put the filter tank cover  on the tank. 
    8.  Connect the hose assembly to the filter pump. 
     
     
     
     
    L20-344 Rev 2
    !WARNING 
    . 
    . 
    4
    ! 
    						
    							FFM PORTABLE FIL TER 
    Foldable handle 
     
     
    Quick- connect coupling 
    for filter screen assembly 
     
     
     
     
    Filter screen assembly 
    Filter envelope 
     
     
    Knurled retaining nut 
     
     
     
     
     
     
     
     
    FFM PORTABLE FIL TER 
    COMPLETELY ASSEMBLED 
     
     
    Quick- connect coupling 
    Pump quick-connect coupling 
     
     
    Filter envelope clip 
     
    Knurled retaining nut 
     
     
     
     
    Filter envelope 
     
    L20-344 Rev 2
    Completely Disassembled 
     
     
     
    Pump quick-connect coupling 
     
    Filter tank 
     
     
     
    Cover 
     
     
     
     
     
     
    Filter envelope cli
    p
    Hose assembly 
    5 
    						
    							 
     
     
     
     
     
     
     
     
     
     
     
     
     
    1. Before filtering the shortening in a fryer turn the thermostat knob to “OFF” or the Gas valve 
     
    to “PILOT” to prevent the fryer from re-lighting during filtering.  On some models the system 
    automatically prevents the burners from lighting when the door of the fryer is open.
     
    2.  Roll filter under drain pipe extension on the fryer and slowly open drain valve handle, letting all the 
    shortening drain into the filter tank.  Leave this valve open. 
    ! 
    Never drain more than one fryer at a time – the filter pan will overflow 
     
    3.  Hold hose assembly nozzle over the fryer kettle, turn on the pump switch and flush sediment out of 
    the fryer.  While the system is cycling, use a long-handled cleaning brush to wipe the bottom of the 
    fryer and push excess crumbs through the drain and into the filter.
     
     
     
     
     
     
    4. Allow the pump to run until the shortening returning into the fryer is clear of sediment, then close drain 
    valve handle and allow the fryer to refill. 
     
     
     
     
     
     
     
     
    5. If filter powder is being used, add 1 cup of powder (for 14” fryers) or 2 cups (for 18” fryers) to 
    either the fry tank or the filter tank. If added to fry tank, make sure powder is completely flushed 
    during fry tank cleaning (Step 3) before closing drain valve (Step 4). If added to filter tank, the 
    powder will be removed when the filter envelope is changed and the filter tank is cleaned. 
     
     
    6 
    L20-344 Rev 2
    CAUTION 
    Never operate the filter unit unless the cooking oil or shortening in the 
    fryers has been brought up to cooking temperature. 
    WARNING 
    Always wear protective heat-resistant gloves when performing the filtering operation
    DANGER 
    . 
    !
    .
    WARNING 
    When cleaning the inside of the frypot, do not damage the temperature and 
    hi-limit probes that protrude into the frypot. 
    WARNING 
    If solid shortening is being used it is very important that all oil is allowed to flow back into 
    the vat and none is left in the hoses. Failure to do so could cause the pump to fail if the 
    oil solidifies in the line. 
    FILTERING INSTRUCTIONS 
     
     
     
    .
      
    						
    							6. On gas-operated thermostat models (such as Anets 14G, 14GS, MXEG, 18EG, 20EG) the thermostat 
    knob can now be turned back to the desired temperature.  CAUTION: On these models the thermostat 
    must be set to “OFF” or the Gas 
    Valve to “PILOT” before filtering or the burners MAY come back on if 
    the doors are closed during filtering. 
    7. On electric-operated thermostat models (such as Anets MX-14E, MX-14EX, MX-14AA, 18E, 18AA, 
    20E, 14EL-14 and 14EL-17) the power switch on the control panel must be reset for the fryer to 
    operate again. 
     
    IMPORTANT NOTE: 
    The pump on this filter unit is equipped with a safety that will turn off the motor if it overheats or an 
    electrical fault occurs.  If this occurs, let the pump motor cool for 15 minutes, then press the manual 
    reset button on the bottom of the motor and restart the motor 
     
     
     
     
     
     
     
     
    OIL DISPOSAL 
     
    . 
     
     
    If the cooking oil or shortening from a fryer is to be disposed, follow steps 1 and 2 from Filtering 
    Instructions in previous section.  Turn on the pump using the switch on the filter and direct the oil into 
    an appropriate device such as an oil shuttle to move the used oil to its disposal tank. 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    L20-344 Rev 2
    .
    DANGER 
    Never run water through the filter system. This will cause rust and corrosion in the 
    motor and pump and will void the Warranty. 
    WARNING 
    Always wear protective heat-resistant gloves when performing the oil disposal operation 
    7 
    						
    							REPLACING THE FIL TER P APER 
    If the filter paper becomes torn, or if the time to filter the oil from one unit becomes excessive, it is time to 
    replace the Filter Envelope. 
    WARNING 
    Only use filter paper envelopes from Anets that have been specifically designed for 
    this filter system
    . Using the wrong type of filter paper can cause damage to the pump 
    system, and will void the Warranty 
     
     
     
     
     
     
    1.  Unplug the cord from the receptacle. 
    2.  Disconnect the line from the pump to the filter screen. 
    3.  Remove the filter cover 
    4.  Remove the filter screen assembly from the filter pan and place on a clean surface for disassembly 
    5. Detach quick-connect coupling on drain tube from knurled retaining nut. 
    6. Detach knurled retaining nut from fitting in screen. 
    7.  Remove filter envelope clip from end of filter screen and folded back end of envelope. 
    8.  Remove filter envelope from filter screen. 
     
     
     
     
    9. Clean the filter pan, filter screen and all components thoroughly using a solution of hot water and 
    detergent.  Make sure that all food and breading particles are removed from the pan and from the filter 
    screen. 
    10.  Dry the pan, the screen and all components completely before starting to reassemble. 
    TER UNIT PREPARATION to install new filter envelope. 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    L20-344 Rev 2
    ! DANGER ! 
    Make sure the filter pan has cooled completely to room temperature before 
    attempting to change the paper. 
    . 
    .
    WARNING 
    The oil soaked filter envelope may still be very hot and could cause burns. 
    11. Follow i
    nstructions under FIL 
    8 
    						
    							FILTER SY STEM  TROUBLESHOOTING GUIDE 
    SOLUTION 
    1.  Make sure the power cord is plugged into the proper 120 Volt receptacle.  
    2.  Turn the switch on the front of the filter to “ON”. 
    3.  If the pump still hasn’t started, depress the thermal overload button on the 
    bottom of the motor.  If the motor is hot to the touch, wait at least 15 minutes 
    before trying this. 
    4.  If the pump starts and stops again in a short time, or if it hums but does not 
    pump, there is a restriction somewhere in the filter screen or in the pump itself. 
    Go 
    to Step 5
    . If there is no reaction from the pump, go to step 6. 
    5.  Allow the oil/shortening in the filter pan to cool, then empty the pan and verify 
    that the filter paper and screen assembly is assembled correctly .  Disassemble the 
    filter screen and look for blockages of sediment or solid shortening within. 
    6.  Problem is with the motor/pump or the wiring. Remove the motor from the 
    filter and bench test by connecting a 120V line to the motor leads.  If it runs, the 
    problem is with the wiring between the motor and the power supply.  If it does not 
    run, the motor needs to be replaced. 
     
     
    1.  If solid shortening is being used allow HOT oil to recirculate through the lines long 
    enough to ensure that all solidified shortening has melted. 
    2.  After all the shortening/oil has been pumped back into the fryer, inspect the 
    filter paper envelope.  Make sure that any excess sediment is removed from the top of 
    the filter paper envelope. 
    3.  If the filter paper envelope is dirty or torn, disassemble the filter screen assembly. 
    Inspect for blockages in the lines.  Replace with a clean filter paper envelope. 
    WARNING 
    Only use filter paper envelopes from Anets that have been specifically 
    designed for this filter system.  Using the wrong type of filter paper 
    can cause damage to the pump system, and will void the warranty 
     
    4. 
    If the oil still returns to the fryer slowly the problem may be a blockage 
    within
     the pump itself.  The pump section of the motor can be easily 
    disassembled to look for blockages of sediment or solid shortening within. 
     
     
     
     
     
     
     
     
     
     
     
     
    L20-344 Rev 2 
    ,.
    PROBLEM 
    Pump does not 
    start when the 
    switch is activated. 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    Filtering procedure is 
    very slow.  Shorten-
    ing/oil returning to the 
    fryer very slow. 
    9 
    						
    All Anetsberger Brothers manuals Comments (0)

    Related Manuals for Anetsberger Brothers Filtration System FFM80FFM150 Portable filters available in 80 lb or 150 lb shortening capacities User Manual