Home
>
Anetsberger Brothers
>
Fryer
>
Anetsberger Brothers 14Inch Gas Fryer 14GS 14 standard User Manual
Anetsberger Brothers 14Inch Gas Fryer 14GS 14 standard User Manual
Here you can view all the pages of manual Anetsberger Brothers 14Inch Gas Fryer 14GS 14 standard User Manual. The Anetsberger Brothers manuals for Fryer are available online for free. You can easily download all the documents as PDF.
Page 1
Anets Inc. Mailing Address: P.O. Box 501, Concord,NH 03302-0501 USA Telephone: 603-225-6684 Shipping Address: 10 Ferry Street, Concord, NH 03301 USA www.anets.com FRYER Models 14G, 14GS 14GU, 14GSU, MX-14EG, MX-14EGU Installation, User Operation, & Maintenance Manual DANGER Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance...
Page 2
DANGER Read these specifications, Code Requirements, Installation Requirements, Installation Instructions, and Operating Instructions very carefully. Failure to follow the Instructions could cause the fryer to malfunction. A fryer malfunction can result in property damage, serious bodily injury, or death. CONTENTS Shipping Container Inspection ........................................................ 3 Fryer Gas Supply Specifications ..................................................... 4...
Page 3
SHlPPlNG CONTAlNER lNSPECTlON fryer carefully for damage. Place the fryer in a safe location, if damage is noted, so that the freight damage claims adjuster can examine the fryer. 3. Save the shipping container for use during leg/ caster installation. Refer to the Installation Instruc- tions for that procedure. Models Covered By This Manual Standard Accessories furnished in the shipping carton for this fryer include: 2 Fryer Baskets 1 Drain Valve Extension 1 Screen 4...
Page 4
FRYER GAS SUPPLY SPEClFlCATlONS Please make sure that Vour desired fr Ver location has gas supplV factors that are suitable for this product: * - BTU/Hr Rating is based on sea level operation. For sites above 2000 feet, reduce this rating 4% for each 1000 feet above sea level. “W.C. = Inches, Water Column. Measure Supply Pressure when all other gas-powered equipment is operating. NOTE: Using a flexible inlet line permits variation in the gas supply line location, both...
Page 5
CODE REQUlREMENTS lMPORTANT: Read the Code Requirements and ALL installation instructions carefully, before starting the installation. Contact the factory if any problems or questions arise. The fryer installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition); the Natural Gas Installation Code, CAN/ CGA-B149.1 (latest edition); or the Propane Gas Installation Code, CAN/CGA-B149.2 (latest edition), as...
Page 6
From the top of the flue on the fryer, allow a minimum of at least 10 inches verti- cal clearance beneath a ventilating hood. Figure 2. Fryer Site Installation Requirements lNSTALLATlON Install the fryer in accordance with the preceding Code Requirements, as well as the following Installation Requirements. 1. DO NOT install this fryer in a mobile home, trailer, or recreational vehicle. 2. Install this fryer in a location that allows it...
Page 7
lNSTALLATlON LEG INSTALLATION INSTRUCTIONS 1. Flatten the shipping carton (after unpacking the fryer and its parts and accessories) for surface protection during leg installation. 2. Position the side of the fryer flat on the carton, exposing the fryer bottom mounting brackets for leg installation, as shown in Figure 3. 3. Place the leg mounting plate flush against the mounting bracket on the fryer bottom. 4. Insert one mounting bolt through a flat washer and then through the proper hole in...
Page 8
lNSTALLATlON lNSTRUCTlONS (Continued) CASTER INSTALLATION INSTRUCTIONS 1. Flatten the shipping carton (after unpacking the fryer and its parts and accessories) for surface protection during leg installation. 2. Position the side of the fryer flat on the carton, exposing the fryer bottom mounting brackets for caster installation, as shown in Figure 4. 3. Place the caster mounting plate flush against the mounting brac- ket on the fryer bottom. 4. Insert one mounting bolt through a...
Page 9
lNSTALLATlON lNSTRUCTlONS (Continued) CASTER LEVELING INSTRUC- CASTER LEVELING INSTRUC- TIONS (Continued) TIONS (Continued) 5 . Completely unscrew the bolts holding the caster mounting plate that requires leveling adjustment. Retain the locking nuts for later reassembly. 6. Reinsert each bolt through its flatwasher and the fryer mounting bracket; next, place a spacer of the required thickness on the bolt before inserting the bolt through its mounting hole on the caster mounting plate and...
Page 10
GAS CONNECTlON Installing your ANETS Fryer requires the fol- lowing procedure, after its legs or casters are pro- perly attached and it is in its desired location. 1. Ensure that the gas control valve knob in the fryer has its OFF position next to the valve mark. 2. Ensure that the gas supply inlet line valve is closed (cross-wise to the pipe line direction). 3. Ensure that all fryer controls are set to OFF. 4. Connect the ¾” gas supply line to the gas line adapter on the lower rear of the...