Home > Anaheim > Stepper > Anaheim Stepper MBC1010175 Users Guide

Anaheim Stepper MBC1010175 Users Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Anaheim Stepper MBC1010175 Users Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 523 Anaheim manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							#L010182May 2005
    MBC10101-75 MBC10101-75MBC10101-75 MBC10101-75
    MBC10101-75
    Bipolar Microstep Driver Bipolar Microstep DriverBipolar Microstep Driver Bipolar Microstep Driver
    Bipolar Microstep Driver
    User’s Guide User’s GuideUser’s Guide User’s Guide
    User’s Guide
    910 East Orangefair Lane, Anaheim, CA 92801
    e-mail: [email protected](714) 992-6990  fax: (714) 992-0471
    website: www.anaheimautomation.com
    ANAHEIM AUTOMATION, INC. ANAHEIM AUTOMATION, INC.ANAHEIM AUTOMATION, INC. ANAHEIM AUTOMATION, INC.
    ANAHEIM AUTOMATION, INC. 
    						
    							#L010182May 2005
    MBC10101-75 Microstep Driver Features MBC10101-75 Microstep Driver FeaturesMBC10101-75 Microstep Driver Features MBC10101-75 Microstep Driver Features
    MBC10101-75 Microstep Driver Features
    • •• •
    •  Enhanced Torque/Speed Output over 12VDC and 24VDC drives
    • •• •
    •  Output Current 10.0 Amps Peak
    • •• •
    •  Built in short circuit and mis-wire shut down
    • •• •
    •  Fixed Step Resolution of 2000 steps per revolution
    • •• •
    •  No Minimum Inductance
    • •• •
    •  Optical Isolation of Control Inputs
    • •• •
    •  Motor ON/OFF input
    Introduction IntroductionIntroduction Introduction
    Introduction
    The MBC10101-75 Microstep Motor Driver has an output current capability of 1.5 Amps minimum to 10.0
    Amps maximum (Peak Rating). The MBC10101-75 driver operates from a DC voltage of 8 - 55 Volts. This
    driver will out perform all standard 12VDC and 24VDC drivers in the industry. If your system is designed
    for a 12VDC or 24VDC specification, this driver will allow your motor to increase its operating output
    performance thanks to this outstanding new driver design.
    The inputs are optically isolated with a minimum sourcing of 1.0 mA per input (+5VDC minimum to +24VDC
    maximum). The clock input is set to receive either positive or negative edge clocks with a maximum
    frequency of 100KHz. The MBC10101-75 driver offers direction control, motor current ON/OFF capabili-
    ties, and built in short circuit and mis-wire shutdown. The Reduce Current Enabled automatically reduces
    motor current to 50% of set value after the last step is made. The driver has built-in features to indicate
    power on (Green LED) and Clocks being received, greater than 100 Hz (Yellow LED). The MBC10101-75
    has a step resolution of 2000 steps per revolution and the bipolar drive configuration handles 4, 6, and 8
    lead motors.
    Optically Isolated Pin Descriptions Optically Isolated Pin DescriptionsOptically Isolated Pin Descriptions Optically Isolated Pin Descriptions
    Optically Isolated Pin Descriptions
    The inputs on the MBC10101-75 are optically isolated with the anode (+) and cathode (-) both brought out
    to the user.  With no current going through the opto-diode the input is considered high. To enable the
    input, a minimum of 1.0 mA needs to be sourced or sinked through the opto-diode. This is done simply by
    placing a voltage of +5 to +24 VDC across the two inputs of the opto-diode. If sourcing current into the
    inputs, then all three cathodes (-) should be tied together and grounded as shown in Figure 2. If sinking
    current, then all three anodes (+) should be tied together to the +voltage as shown in Figure 1.
    The 
    optional output on the MBC10101-75 is an opto-decoupled open collector output. When normal op-
    eration occurs, this output will conduct current into the emitter. Care must be taken not to pass more than
    50mA through this transistor. Please contact Anaheim Automation for functionality of this output.
    To enable an input, apply a DC voltage source of +5VDC to +24VDC across the inputs. The Anodes (+)
    are pins 1, 3, and 5 on TB1 and the Cathodes (-) are pins 2, 4, and 6 on TB1.
    Connecting the Step Motor Connecting the Step MotorConnecting the Step Motor Connecting the Step Motor
    Connecting the Step Motor
    Phase 1 and 3 of the Step Motor is connected between pins 1 and 2 on the TB3.  Phase 2 and 4 of the
    Step Motor is connected between pins 3 and 4 on TB3. Refer to Figures 1 & 2 for TYPICAL APPLICA-
    TION HOOK-UP.
    NOTE NOTENOTE NOTE
    NOTE: The physical direction of the motor with respect to the direction input will depend on the connection
    of the motor windings.  To reverse the direction of the motor with respect to the direction input, swap the
    wires on Phase 1 and  Phase 3.
    WARNING: Do not connect or disconnect motor wires while power is applied! This driver  WARNING: Do not connect or disconnect motor wires while power is applied! This driver WARNING: Do not connect or disconnect motor wires while power is applied! This driver  WARNING: Do not connect or disconnect motor wires while power is applied! This driver 
    WARNING: Do not connect or disconnect motor wires while power is applied! This driver 
    does not does notdoes not does not
    does not
    protect itself if the motor is disconnected while powered. protect itself if the motor is disconnected while powered.protect itself if the motor is disconnected while powered. protect itself if the motor is disconnected while powered.
    protect itself if the motor is disconnected while powered. 
    						
    							#L010182May 2005
    Terminal Block Descriptions Terminal Block DescriptionsTerminal Block Descriptions Terminal Block Descriptions
    Terminal Block Descriptions
    Power Supply Requirements Power Supply RequirementsPower Supply Requirements Power Supply Requirements
    Power Supply Requirements
    The MBC10101-75 can only be powered by a DC voltage  with a range of 8 to 55VDC.
    Power Draw: Power Draw:Power Draw: Power Draw:
    Power Draw:
    The power consumption of this driver from the DC power supply is determined by the DC voltage in. The
    power draw is also motor dependent. Motors exceeding 200 watts are not intended for the MBC10101-75
    driver. The following formula can be used to determine the maximum power delivered by the driver:
    Output Power = (VDC in) x 4.
    Power Supply Ordering Information Power Supply Ordering InformationPower Supply Ordering Information Power Supply Ordering Information
    Power Supply Ordering Information
    Table 1: Pin descriptions for terminal blocks
    # n i P#n i P
    # n i P# n i P#n i Pn o i t p i r c s e Dno i t p i r c s e D
    n o i t p i r c s e Dn o i t p i r c s e Dno i t p i r c s e D
    ) 1 B T ( 1 k c o l B l a n i m r e T)1 B T ( 1 k c o l B l a n i m r e T
    ) 1 B T ( 1 k c o l B l a n i m r e T) 1 B T ( 1 k c o l B l a n i m r e T)1 B T ( 1 k c o l B l a n i m r e T
    1 1
    1 11:) + ( e d o n A t u p n I k c o l C p e t S:) + ( e d o n A t u p n I k c o l C p e t S
    : ) + ( e d o n A t u p n I k c o l C p e t S: ) + ( e d o n A t u p n I k c o l C p e t S:) + ( e d o n A t u p n I k c o l C p e t Se n o r o t o m e h t s e c n a v d a t u p n i d e t a l o s i s i h t n o e g d e g n i o g e v i t i s o p A
    . t n e m e r c n i
    2 2
    2 22)- ( e d o h t a C t u p n I k c o l C p e t S)- ( e d o h t a C t u p n I k c o l C p e t S
    ) - ( e d o h t a C t u p n I k c o l C p e t S) - ( e d o h t a C t u p n I k c o l C p e t S)- ( e d o h t a C t u p n I k c o l C p e t S
    3 3
    3 33:) + ( e d o n A n o i t c e r i D:) + ( e d o n A n o i t c e r i D
    : ) + ( e d o n A n o i t c e r i D: ) + ( e d o n A n o i t c e r i D:) + ( e d o n A n o i t c e r i Dn o i t c e r i d l a c i s y h P . r o t o m e h t f o n o i t c e r i d e h t e g n a h c o t d e s u s i t u p n i d e t a l o s i s i h T
    . s g n i d n i w r o t o m e h t f o n o i t c e n n o c e h t n o s d n e p e d o s l a
    4 4
    4 44)- ( e d o h t a C n o i t c e r i D)- ( e d o h t a C n o i t c e r i D
    ) - ( e d o h t a C n o i t c e r i D) - ( e d o h t a C n o i t c e r i D)- ( e d o h t a C n o i t c e r i D
    5 5
    5 55:) + ( e d o n A F F O / N O:) + ( e d o n A F F O / N O
    : ) + ( e d o n A F F O / N O: ) + ( e d o n A F F O / N O:) + ( e d o n A F F O / N O. r e v i r d e h t f o n o i t c e s t u p t u o e h t e l b a s i d d n a e l b a n e o t d e s u s i t u p n i d e t a l o s i s i h T
    . k c o l c p e t s e h t t i b i h n i t o n s e o d t u p n i s i h t , r e v e w o H . d e l b a n e e r a s t u p t u o e h t ) n e p o ( H G I H n e h W
    6 6
    6 66)- ( e d o h t a C F F O / N O)- ( e d o h t a C F F O / N O
    ) - ( e d o h t a C F F O / N O) - ( e d o h t a C F F O / N O)- ( e d o h t a C F F O / N O
    7 7
    7 77:) r o t c e l l o C ( 1 T U O:) r o t c e l l o C ( 1 T U O
    : ) r o t c e l l o C ( 1 T U O: ) r o t c e l l o C ( 1 T U O:) r o t c e l l o C ( 1 T U On e h W . t u p t u o r o t c e l l o c n e p o d e l p u o c e d - o t p o n a s i 5 7 - 1 0 1 0 1 C B M e h t n o t u p t u o e h T
    s s a p o t t o n n e k a t e b t s u m e r a C . r e t t i m e e h t o t n i t n e r r u c t c u d n o c l l i w t u p t u o s i h t , s r u c c o n o i t a r e p o l a m r o n
    . r o t s i s n a r t s i h t h g u o r h t A m 0 5 n a h t e r o m
    8 8
    8 88)r e t t i m E ( 1 T U O)r e t t i m E ( 1 T U O
    ) r e t t i m E ( 1 T U O) r e t t i m E ( 1 T U O)r e t t i m E ( 1 T U O
    ) 2 B T ( 2 k c o l B l a n i m r e T)2 B T ( 2 k c o l B l a n i m r e T
    ) 2 B T ( 2 k c o l B l a n i m r e T) 2 B T ( 2 k c o l B l a n i m r e T)2 B T ( 2 k c o l B l a n i m r e T
    1 1
    1 11)C D V 5 5 - 8 ( r e v i r d e h t r o f e g a t l o v t u p n I : N I C D)C D V 5 5 - 8 ( r e v i r d e h t r o f e g a t l o v t u p n I : N I C D
    ) C D V 5 5 - 8 ( r e v i r d e h t r o f e g a t l o v t u p n I : N I C D) C D V 5 5 - 8 ( r e v i r d e h t r o f e g a t l o v t u p n I : N I C D)C D V 5 5 - 8 ( r e v i r d e h t r o f e g a t l o v t u p n I : N I C D
    2 2
    2 22eg a t l o v r e v i r d r o f h t a p n r u t e R : d n u o r Geg a t l o v r e v i r d r o f h t a p n r u t e R : d n u o r G
    e g a t l o v r e v i r d r o f h t a p n r u t e R : d n u o r Ge g a t l o v r e v i r d r o f h t a p n r u t e R : d n u o r Geg a t l o v r e v i r d r o f h t a p n r u t e R : d n u o r G
    ) 3 B T ( 3 k c o l B l a n i m r e T)3 B T ( 3 k c o l B l a n i m r e T
    ) 3 B T ( 3 k c o l B l a n i m r e T) 3 B T ( 3 k c o l B l a n i m r e T)3 B T ( 3 k c o l B l a n i m r e T
    1 1
    1 11ro t o M p e t S e h t f o 1 e s a h P : A e s a h Pro t o M p e t S e h t f o 1 e s a h P : A e s a h P
    r o t o M p e t S e h t f o 1 e s a h P : A e s a h Pr o t o M p e t S e h t f o 1 e s a h P : A e s a h Pro t o M p e t S e h t f o 1 e s a h P : A e s a h P
    2 2
    2 22ro t o M p e t S e h t f o 3 e s a h P : A / e s a h Pro t o M p e t S e h t f o 3 e s a h P : A / e s a h P
    r o t o M p e t S e h t f o 3 e s a h P : A / e s a h Pr o t o M p e t S e h t f o 3 e s a h P : A / e s a h Pro t o M p e t S e h t f o 3 e s a h P : A / e s a h P
    3 3
    3 33ro t o M p e t S e h t f o 2 e s a h P : B e s a h Pro t o M p e t S e h t f o 2 e s a h P : B e s a h P
    r o t o M p e t S e h t f o 2 e s a h P : B e s a h Pr o t o M p e t S e h t f o 2 e s a h P : B e s a h Pro t o M p e t S e h t f o 2 e s a h P : B e s a h P
    4 4
    4 44ro t o M p e t S e h t f o 4 e s a h P : B / e s a h Pro t o M p e t S e h t f o 4 e s a h P : B / e s a h P
    r o t o M p e t S e h t f o 4 e s a h P : B / e s a h Pr o t o M p e t S e h t f o 4 e s a h P : B / e s a h Pro t o M p e t S e h t f o 4 e s a h P : B / e s a h P
    y l p p u S C Dn o i t p i r c s e Dr e w o P
    A 4 V 0 4 A S PNI C A V 0 3 2 / 5 7 1 , A 4 @ V 0 4st t a W 0 6 1
    A 7 . 2 V 4 2 A S PNI C A V 5 6 2 - 0 9 , A 7 . 2 @ V 4 2st t a W 5 6
    A 8 V 0 4 A S PNI C A V 5 1 1 , A 8 @ V 0 4st t a W 0 2 3
    Table 2: Power Supply Ordering Information 
    						
    							#L010182May 2005
    Absolute Maximum Ratings Absolute Maximum RatingsAbsolute Maximum Ratings Absolute Maximum Ratings
    Absolute Maximum Ratings
    Input Voltage: 55VDC
    Output Current: 10.0 AMPS PEAK
    Max Plate Temperature: 70° C
    Storage Temperature: 0° to +50° C
    Input Voltage (For isolated inputs):  +5V to +24V at 2.5mA
    Electrical Specifications Electrical SpecificationsElectrical Specifications Electrical Specifications
    Electrical Specifications
    m e t Ime t I
    m e t Im e t Ime t In i Mni M
    n i Mn i Mni Mp y Tpy T
    p y Tp y Tpy Tx a Mxa M
    x a Mx a Mxa Ms t i n Ust i n U
    s t i n Us t i n Ust i n U
    ) r e w o P ( e g a t l o V t u p n I)r e w o P ( e g a t l o V t u p n I
    ) r e w o P ( e g a t l o V t u p n I) r e w o P ( e g a t l o V t u p n I)r e w o P ( e g a t l o V t u p n I855CD V
    t n e r r u C t u p t u O e s a h Ptn e r r u C t u p t u O e s a h P
    t n e r r u C t u p t u O e s a h Pt n e r r u C t u p t u O e s a h Ptn e r r u C t u p t u O e s a h P1. 11. 7)S M R ( A
    t n e r r u C t u p t u O e s a h Ptn e r r u C t u p t u O e s a h P
    t n e r r u C t u p t u O e s a h Pt n e r r u C t u p t u O e s a h Ptn e r r u C t u p t u O e s a h P5. 10. 0 1)K A E P ( A
    ) s t u p n I ( e g a t l o V t u p n I)s t u p n I ( e g a t l o V t u p n I
    ) s t u p n I ( e g a t l o V t u p n I) s t u p n I ( e g a t l o V t u p n I)s t u p n I ( e g a t l o V t u p n I542CD V
    y c n e u q e r F k c o l Cyc n e u q e r F k c o l C
    y c n e u q e r F k c o l Cy c n e u q e r F k c o l Cyc n e u q e r F k c o l C000 1zH k
    y c n e u q e r F g n i p p o h Cyc n e u q e r F g n i p p o h C
    y c n e u q e r F g n i p p o h Cy c n e u q e r F g n i p p o h Cyc n e u q e r F g n i p p o h C032343zH k
    e r u t a r e p m e T n o i t a r e p Oer u t a r e p m e T n o i t a r e p O
    e r u t a r e p m e T n o i t a r e p Oe r u t a r e p m e T n o i t a r e p Oer u t a r e p m e T n o i t a r e p O007C
    Table 3: MBC10101-75 electrical specifications
    Setting the Output Current Setting the Output CurrentSetting the Output Current Setting the Output Current
    Setting the Output Current
    WARNING: Do not set the current setting above the step motors rated current. When using a WARNING: Do not set the current setting above the step motors rated current. When using aWARNING: Do not set the current setting above the step motors rated current. When using a WARNING: Do not set the current setting above the step motors rated current. When using a
    WARNING: Do not set the current setting above the step motors rated current. When using a
    higher current setting into a motor, the motor will overheat and burnup. Should this occur, the higher current setting into a motor, the motor will overheat and burnup. Should this occur, thehigher current setting into a motor, the motor will overheat and burnup. Should this occur, the higher current setting into a motor, the motor will overheat and burnup. Should this occur, the
    higher current setting into a motor, the motor will overheat and burnup. Should this occur, the
    driver will also be damaged. driver will also be damaged.driver will also be damaged. driver will also be damaged.
    driver will also be damaged.
    The output current on the MBC10101-75 is set by an onboard potentiometer. This potentiometer deter-
    mines the per phase peak output current of the driver. The relationship between the output current and the
    potentiometer value is as follows:
    Table 4:  Potentiometer values with respect to the output current
    Refer to Table 5 for specific motor current settings. Refer to Table 5 for specific motor current settings.Refer to Table 5 for specific motor current settings. Refer to Table 5 for specific motor current settings.
    Refer to Table 5 for specific motor current settings.
    Reducing Output Current Reducing Output CurrentReducing Output Current Reducing Output Current
    Reducing Output Current
    Reducing the output current is accomplished automatically and occurs approximately 1 second after the
    last positive going edge of the step clock input. The amount of current per phase in the reduction mode is
    approximately 50% of the set current.
    t n e r r u C k a e Ptn e r r u C k a e P
    t n e r r u C k a e Pt n e r r u C k a e Ptn e r r u C k a e Pg n i t t e S r e t e m o i t n e t o Pgn i t t e S r e t e m o i t n e t o P
    g n i t t e S r e t e m o i t n e t o Pg n i t t e S r e t e m o i t n e t o Pgn i t t e S r e t e m o i t n e t o Pt n e r r u C k a e Ptn e r r u C k a e P
    t n e r r u C k a e Pt n e r r u C k a e Ptn e r r u C k a e Pg n i t t e S r e t e m o i t n e t o Pgn i t t e S r e t e m o i t n e t o P
    g n i t t e S r e t e m o i t n e t o Pg n i t t e S r e t e m o i t n e t o Pgn i t t e S r e t e m o i t n e t o P
    A 5 . 1%0A 0 . 7%0 6
    A 3 . 2%0 1A 9 . 7%0 7
    A 1 . 3%0 2A 7 . 8%0 8
    A 0 . 4%0 3A 6 . 9%0 9
    A 0 . 5%0 4A 0 1%0 0 1
    A 0 . 6%0 5- --- 
    						
    							#L010182May 2005
    Hook Up Drawings Hook Up DrawingsHook Up Drawings Hook Up Drawings
    Hook Up Drawings
    Figure 1: Hook up for current sinking inputs
    Dimension Drawing Dimension DrawingDimension Drawing Dimension Drawing
    Dimension Drawing
    Figure 5: MBC10101-75 dimensions Figure 2: Hook up for current sourcing inputs 
    						
    							#L010182May 2005
    Motor Selection Motor SelectionMotor Selection Motor Selection
    Motor Selection
    The MBC10101-75 is a Bipolar Microstep Driver that is compatible with both Bipolar and Unipolar Motor
    Configurations, (i.e. 8 and 4 lead motors, and 6 lead center tapped motors).
    Step motors with low current ratings and high inductance will perform better at low speeds, providing
    higher low-end torque. Motors with high current ratings and low inductance will perform better at higher
    speeds, providing more high-end torque. Higher voltages will cause the current to flow faster through the
    motor coils. This in turn means higher step rates can be achieved. 
    Care should be taken not to exceed the
    maximum voltage of the driver.
    Since the MBC10101-75 is a constant current source, it is not necessary to use a motor that is rated at the
    same voltage as the supply voltage. What is important is that the MBC10101-75 is set to the appropriate
    current level based on the motor being used.  Refer to the following chart for setting the current potentiom-
    eter based on the current code in the part number of the motor. Examples of motor part numbers are
    shown below. Anaheim Automation offers a comprehensive line of step motors in 14, 17, 23, 34 and 42
    frame sizes. Contact the factory to verify motor compatibility with the MBC10101-75.
    Step Motor Current Setting Guide Step Motor Current Setting GuideStep Motor Current Setting Guide Step Motor Current Setting Guide
    Step Motor Current Setting Guide
    Anaheim Automation offers motor cable, making hook-ups quick and easy! Anaheim Automation offers motor cable, making hook-ups quick and easy!Anaheim Automation offers motor cable, making hook-ups quick and easy! Anaheim Automation offers motor cable, making hook-ups quick and easy!
    Anaheim Automation offers motor cable, making hook-ups quick and easy!
    Contact the factory or visit our website for more motor and cable offerings. Contact the factory or visit our website for more motor and cable offerings.Contact the factory or visit our website for more motor and cable offerings. Contact the factory or visit our website for more motor and cable offerings.
    Contact the factory or visit our website for more motor and cable offerings.
    e l p m a x E r o t o Mel p m a x E r o t o M
    e l p m a x E r o t o Me l p m a x E r o t o Mel p m a x E r o t o Mt n e r r u C r o t o Mtn e r r u C r o t o M
    t n e r r u C r o t o Mt n e r r u C r o t o Mtn e r r u C r o t o M
    e d o C r e b m u Ned o C r e b m u N
    e d o C r e b m u Ne d o C r e b m u Ned o C r e b m u Nr a l o p i n Ura l o p i n U
    r a l o p i n Ur a l o p i n Ura l o p i n U
    g n i t a Rgn i t a R
    g n i t a Rg n i t a Rgn i t a Rk a e P s e i r e Ska e P s e i r e S
    k a e P s e i r e Sk a e P s e i r e Ska e P s e i r e S
    g n i t a Rgn i t a R
    g n i t a Rg n i t a Rgn i t a Rk a e P l e l l a r a Pka e P l e l l a r a P
    k a e P l e l l a r a Pk a e P l e l l a r a Pka e P l e l l a r a P
    g n i t a Rgn i t a R
    g n i t a Rg n i t a Rgn i t a Rs e i r e Sse i r e S
    s e i r e Ss e i r e Sse i r e S
    t n e r r u Ctn e r r u C
    t n e r r u Ct n e r r u Ctn e r r u C
    g n i t t e Sgn i t t e S
    g n i t t e Sg n i t t e Sgn i t t e Sl e l l a r a Ple l l a r a P
    l e l l a r a Pl e l l a r a Ple l l a r a P
    t n e r r u Ctn e r r u C
    t n e r r u Ct n e r r u Ctn e r r u C
    g n i t t e Sgn i t t e S
    g n i t t e Sg n i t t e Sgn i t t e S
    1 D 3 21D 3 2
    1 D 3 21 D 3 21D 3 2202 0
    2 02 020SS
    S SS2 02 0
    2 02 020
    A 0 . 1A0 . 1A0 . 2-- - -%5
    3 L 3 23L 3 2
    3 L 3 23 L 3 23L 3 2303 0
    3 03 0308W L - D8W L - D
    8 W L - D8 W L - D8W L - D3 03 0
    3 03 030
    A 5 . 1A5 . 1A0 . 3%0%0 2
    1 N 4 31N 4 3
    1 N 4 31 N 4 31N 4 3404 0
    4 04 0408W L - S8W L - S
    8 W L - S8 W L - S8W L - S4 04 0
    4 04 040
    A 0 . 2A0 . 2A0 . 4%5%0 3
    0 4 L 3 204 L 3 2
    0 4 L 3 20 4 L 3 204 L 3 2505 0
    5 05 0508W L - D8W L - D
    8 W L - D8 W L - D8W L - D5 05 0
    5 05 050
    A 5 . 2A5 . 2A0 . 5%0 1%0 4
    1 A 4 31A 4 3
    1 A 4 31 A 4 31A 4 3606 0
    6 06 060BB
    B BB6 06 0
    6 06 060
    A 0 . 3A0 . 3A0 . 6%0 2%0 5
    2 N 4 32N 4 3
    2 N 4 32 N 4 32N 4 3707 0
    7 07 0708W L - S8W L - S
    8 W L - S8 W L - S8W L - S7 07 0
    7 07 070
    A 5 . 3A5 . 3A0 . 7%5 2%0 6
    1 K 4 31K 4 3
    1 K 4 31 K 4 31K 4 3808 0
    8 08 0808W L - S8W L - S
    8 W L - S8 W L - S8W L - S8 08 0
    8 08 080
    A 0 . 4A0 . 4A0 . 8%0 3%0 7
    2 N 2 42N 2 4
    2 N 2 42 N 2 42N 2 4909 0
    9 09 090BC - SBC - S
    B C - SB C - SBC - S9 09 0
    9 09 090
    A 5 . 4A5 . 4A0 . 9%5 3%5 8
    3 L 3 23L 3 2
    3 L 3 23 L 3 23L 3 2010 1
    0 10 1018W L - S8W L - S
    8 W L - S8 W L - S8W L - S0 10 1
    0 10 101
    A 0 . 5A0 . 5A0 . 0 1%0 4%0 0 1
    3 D 4 33D 4 3
    3 D 4 33 D 4 33D 4 3111 1
    1 11 111DD
    D DD1 11 1
    1 11 111
    A 5 . 5A5 . 5A0 . 1 1%5 4%0 0 1
    1 K 2 41K 2 4
    1 K 2 41 K 2 41K 2 4212 1
    2 12 121BC - SBC - S
    B C - SB C - SBC - S2 12 1
    2 12 121
    A 0 . 6A0 . 6A0 . 2 1%0 5%0 0 1
    2 D 4 32D 4 3
    2 D 4 32 D 4 32D 4 3313 1
    3 13 131SS
    S SS3 13 1
    3 13 131
    A 5 . 6A5 . 6A0 . 3 1%5 5%0 0 1
    3 N 4 33N 4 3
    3 N 4 33 N 4 33N 4 3414 1
    4 14 1418W L - S8W L - S
    8 W L - S8 W L - S8W L - S4 14 1
    4 14 141
    A 0 . 7A0 . 7A0 . 4 1%0 6%0 0 1
    1 N 2 41N 2 4
    1 N 2 41 N 2 41N 2 4515 1
    5 15 151BC - DBC - D
    B C - DB C - DBC - D5 15 1
    5 15 151
    A 5 . 7A5 . 7A0 . 5 1%5 6-- - -
    4 K 4 34K 4 3
    4 K 4 34 K 4 34K 4 3616 1
    6 16 1618W L - S8W L - S
    8 W L - S8 W L - S8W L - S6 16 1
    6 16 161
    A 0 . 8A0 . 8A0 . 6 1%0 7-- - -
    1 D 2 41D 2 4
    1 D 2 41 D 2 41D 2 4919 1
    9 19 191DD
    D DD9 19 1
    9 19 191
    A 5 . 9A5 . 9A0 . 9 1%0 9-- - -
    3 N 2 43N 2 4
    3 N 2 43 N 2 43N 2 4222 2
    2 22 222BC - SBC - S
    B C - SB C - SBC - S2 22 2
    2 22 222
    A 0 . 1 1A0 . 1 1A0 . 2 2%0 0 1-- - -
    2 D 2 42D 2 4
    2 D 2 42 D 2 42D 2 4525 2
    5 25 252SS
    S SS5 25 2
    5 25 252
    A 5 . 2 1A5 . 2 1A0 . 5 2%0 0 1-- - -
    Table 5: Table selection for Anaheim Automation motor current settings. 
    						
    							#L010182May 2005
    When configuring the motor in a series configuration series configurationseries configuration series configuration
    series configuration (connected from end to end with the
    center tap floating) use the specified per Phase (or unipolar) current rating to determine the
    current setting potentiometer value.
    Determining Output Current Determining Output CurrentDetermining Output Current Determining Output Current
    Determining Output Current
    The output current for the motor used when microstepping is determined differently from that of a full/half
    step unipolar driver. In the MBC10101-75, a sine/cosine output function is used in rotating the motor. The
    output current for a given motor is determined by the motors current rating and the wiring configuration of
    the motor. There is a current adjustment potentiometer used to set the output current of the MBC10101-
    75. This sets the peak output current of the sine/cosine waves. The specified motor current (which is the
    unipolar value) is multiplied by a factor of 1.0, 1.4, or 2.0 depending on the motor configuration (series,
    half-coil, or parallel).
    WARNING: Do not set the current setting above the step motors rated current. When using a WARNING: Do not set the current setting above the step motors rated current. When using aWARNING: Do not set the current setting above the step motors rated current. When using a WARNING: Do not set the current setting above the step motors rated current. When using a
    WARNING: Do not set the current setting above the step motors rated current. When using a
    higher current setting into a motor, the motor will overheat and burnup. Should this occur, the higher current setting into a motor, the motor will overheat and burnup. Should this occur, thehigher current setting into a motor, the motor will overheat and burnup. Should this occur, the higher current setting into a motor, the motor will overheat and burnup. Should this occur, the
    higher current setting into a motor, the motor will overheat and burnup. Should this occur, the
    driver will also be damaged. driver will also be damaged.driver will also be damaged. driver will also be damaged.
    driver will also be damaged.
    Step Motor Configurations Step Motor ConfigurationsStep Motor Configurations Step Motor Configurations
    Step Motor Configurations
    Step motors can be configured as 4, 6, or 8 leads. Each configuration requires different currents. Refer to
    the lead configurations and the procedures to determine their output current.
    WARNING! WARNING!WARNING! WARNING!
    WARNING! Step motors will run hot even when configured correctly. Damage may occur to the motor if
    a higher than specified current is used. Most specified motor currents are maximum values. Care
    should be taken to not exceed these ratings.
    6 Lead Motors 6 Lead Motors6 Lead Motors 6 Lead Motors
    6 Lead Motors
    When configuring a 6 lead motor in a half-coil configuration half-coil configurationhalf-coil configuration half-coil configuration
    half-coil configuration (connected from one end of the coil to the
    center tap), multiply the specified per Phase (or unipolar) current rating by 1.4 to determine the current
    setting potentiometer value. This configuration will provide more torque at higher speeds when compared
    to the series configuration. 
    						
    							#L010182May 2005
    4 Lead Motors 4 Lead Motors4 Lead Motors 4 Lead Motors
    4 Lead Motors
    Multiply the specified series  series series  series 
    series motor current by 1.4 to determine the current adjustment potentiometer
    value. Four Lead Motors are usually rated with their appropriate series current, as opposed to the 
    Phase
    Current
    , which is the rating for 6 and 8 lead motors.
    8 Lead Motors 8 Lead Motors8 Lead Motors 8 Lead Motors
    8 Lead Motors
    Series Connection: Series Connection:Series Connection: Series Connection:
    Series Connection: When configuring the motor windings in series, use the per Phase (or unipolar)
    current rating to determine the current setting potentiometer value.
    Parallel Connection: Parallel Connection:Parallel Connection: Parallel Connection:
    Parallel Connection: When configuring the motor windings in parallel, multiply the per Phase (or unipo-
    lar) current rating by 2.0 to determine the current setting potentiometer value.
    NOTE: NOTE:NOTE: NOTE:
    NOTE: After the current has been determined, according to the motor connections above, use Table 3 to
    choose the proper setting for the current setting potentiometer. 
    						
    							#L010182May 2005
    Torque Speed Curves Torque Speed CurvesTorque Speed Curves Torque Speed Curves
    Torque Speed Curves
    ANAHEIM AUTOMATION, INC. 
    						
    All Anaheim manuals Comments (0)

    Related Manuals for Anaheim Stepper MBC1010175 Users Guide