Anaheim Stepper DPY50601 Users Guide

September 2012 L01019531
Analog Speed On (Off) Sets the analog speed input feature on or off.
Set Analog Speed Sets the maximum (running) speed based on the analog input.
Analog Speed Lower Limit Sets the analog speed lower limit to the value specifi ed.
Analog Speed Upper Limit Sets the analog speed upper limit to the value specifi ed.
Analog Position On (Off) Sets the analog position input feature on or off.
Goto Analog Position Motor will move to the position based on the analog input.
Analog Position...

September 2012 L01019532
PPS -> RPS Convert from pulses per second to revolution per second.
RPS ->PPS Convert from revolution per second to pulses per second.
Steps Per RevEnter the number of steps per revolution of the step motor.  The default is for a 
200 step/rev motor in half step, which is equal to 400.
Close Exit Calculator.
Calculator 

September 2012 L01019533
Direct mode is used to directly control the motion for real time movements through serial communication.  
The DPY50601 has 40 commands which are easy to remember for direct movement of a step motor.
COM Port Settings
Baud Rate: 38400
Parity: None
Data Bits: 8
Stop Bits: 1
Flow Control: Xon/Xoff
Unit Selection
In order to select a unit the @ command followed by 0 (address of the unit) must be sent.
NOTE: There should be no spaces between the @ and address select.
How to select...

September 2012 L01019534
A - Acceleration/Deceleration
Format:   A[value]
Description: This command sets the acceleration profi le which is an integer value between 
100 and 9,999,999.  The higher the value, the faster the motor acceleration.
Range:    100 - 9,999,999
B - Base Speed
Format:   B[value]
Description:  This command sets the base (start) speed for motion.  This value must be 
set before motion begins and be less then the maximum speed and fast jog speed.
Range:    1 - 5000
C - Number of Steps...

September 2012 L01019535
ED - Encoder Delay
Format:   ED[value]
Description:  This command sets the wait time a specifi ed number of milliseconds after 
a relative index or absolute move is fi nished, before reading the encoder.  This is used to 
remove the ringing that might be associated with the mechanics of the system.  This com-
mand is used in conjunction with the encoder auto correct “EA” command.
Range:    0 - 65535
EM - Encoder Motor Ratio
Format:   EM[value]
Description:  This represents the...

September 2012 L01019536
G - Go Number of Steps
Format:   G
Description:  This command is used to send a set number of clocks out of the DPY50601 
controller.  An N or P command must be entered before the G command.  The ramp profi le 
is specifi ed by the B (base speed), M (max speed), and A (acceleration/deceleration) com-
mands.
H - Home
Format:   H[0 or 1]
Description: 
Home Types:  H0:  In type 0 homing, the DPY50601 will send clocks until a soft limit is 
reached, then ramp down to base speed....

September 2012 L01019537
M - Max Speed and Analog Speed
Format 1:  M[value]
Description:  This command sets the maximum (running) speed for motion.  This value 
must be set before motion begins, and be greater than the base speed.
Range:    1 - 50000
Format 2:  M
Description: This command uses the voltage on input 1 to calculate and set the max speed.  
The analog speed must be enabled for this command to work.  This command is used in 
conjunction with the analog speed “;”, the analog speed lower limit...

September 2012 L01019538
P - Absolute Position and Analog Position
Format 1:  P[value]
Description:  This command calculates and sets the number of clocks for the DPY50601 
to send out following a G command.  Motion is not activated by this command; it only sets 
the register.  (N = P - Z)
Range:    -8388607 to +8388607
Format 2:  P
Description:  This command uses the voltage on input 1 to calculate and set the number 
of clocks for the DPY50601 to send out following a G command.  The analog position...

September 2012 L01019539
V - Verify
Format:   V[command]
Description:  This command can be used with most commands to verify the register con-
tents.  This is a read only command.  Valid Commands are shown below.
Z - Position 
Format:   Z[value]
Description:  This command sets the current position as a reference.  This register can 
contain a positive or negative value but, cannot be changed while motion is in progress.
Range:    -8388607 to +8388607
! - Error Codes Register
Format:   !
Description:...

September 2012 L01019540
% - Verify Address Register
Format:    %   (No address is needed before this function. @% will return the address)
Description:  This command requests the DPY50601 controller to return its internal ad-
dress number to the PC or PLC.
‘ - Index on the Fly Enabled
Format:   ‘[0 or 1]
Description:  This command will either enable or disable the index on the fl y function.  To 
enable the function, use a 1.  To disable the function use a 0.  This command is used in 
conjunction with...