Ampro Corporation Ampro Projector 5200 User Manual

9
5200 User’s Manual
Remote Control Installation and Operation
Connecting the
ReceiverReceiv er The external serial receiv er lets you control your mouse from up to 45
feet away. To connect the Mind Path external receiver to your computer follow
these steps:

  Turn off your projector.

  Plug the free end of the external serial receiver cable into a serial port 2
(COM2) on your projector.

  Turn on your projector.
Positioning the
ReceiverOnce the receiver is connected to your projector, take care to...

Remote Control Installation and Operation
10
5200 User’s Manual

 - Power On, 2nd Function; Toggle between Sources
 - Standby; toggle the projected image on/off (Video Mute)
 - Display Main Menu, Enter highlighted function
 - Cycle through control; Use to scroll “left” through controls
 - Cycle through controls; Use to scroll “right” through controls.
Mouse Pad
 – Move the mouse cursor, Enter function
Press Edge Cursor Moves
Click Center Left Click
Click Center Twice Left Double Click
Press and Hold...

11
5200 User’s Manual
Keyboard Installation and Operation
Installing the
Batteries
  Turn the keyboard over onto its face.

  By pressing the two latch tabs simultaneously, pry open the battery door with your
fingers.

  Insert 4 AA alkaline batteries with the positive (+) and negative (-) orientation as shown
inside the compartment (negative is at the flat end of the battery and goes towards the
spring).

  Replace the batteries door and make sure both latch tabs snap into place.

  Turn the projector...

Keyboard Installation and Operation
12
5200 User’s Manual
Positioning the
ReceiverThe receiv er is multi-positional. It can stand up or lay flat on either side. If you are placing it
on a table or desktop. It is best to stand the receiv er up to minimize any disruption of the
signal by the table or desktop.
When you are mounting or positioning the receiver be careful not to block the lens from line-
of-sight contact with the Keyboard. The Keyboard is powerful enough to bounce the infrared
(IR) signal off...

Keyboard Installation and Operation
13
5200 User’s Manual
Keyboard
OperationThe IR remote Control keystrokes can be simulated using the IR Keyboard. The following is
a list of projector commands using the Keyboard.
NOTE: The IR Remote Control key equivalent is represented in parenthesis ( )
Keystrokes Description
POWER (
): Press    keys simultaneously to power
the display engine “on”.
2
nd Function: Use    to toggle between available
sources.
POWER OFF: Use the    key sequences to explicitly
power-off...

14
5200 User’s Manual
Local Control and Indicators
Controls
Located at the rear of the projector is the local control panel. The controls allow the user to
perform the following functions.

  PWR (POWER): Allows the user to power the projector on and off.

  MENU: Enters the On-Screen-Display Mode.

  SEL (SELECT): Use the SEL key to select the highlighted function.

  STBY (STANDBY): Use to toggle the projected image on or off.

  ARROW KEYS: Use to scroll through menu items. Once an item has been...

15
5200 User’s Manual
Source Connections
Essential Cable
ConnectionsBefore applying AC power to the 5000 Series projector, both IR receivers MUST BE
CONNECTED
.


  The IR receiver connections for the keyboard and remote control are located on the PC
card cage.


  To access the PC card cage and connectors, turn the ¼ turn captive screw located on
the left side of the access panel, and gently open the door.


  Route the connectors from the IR receiv ers up through the access slot located on the...

16
5200 User’s Manual
Basic Operation and Menu Navigation
Power Up
The AmPro 5200 Series follows an initial “power-up” sequence from the time the main AC is
toggled “on” to the time an image is displayed.


  With the two receivers installed, plug the main power cord into a receptacle.


  Toggle the main ac switch “on”. The projector will automatically start, first displaying the
Windows boot-up screen, then the Scan Disk operation.


  The projector will then automatically search for an external...

Basic Operation and Menu Navigation
17
5200 User’s Manual
Menu Navigation and Conventions
Command Buttons –
 Command
buttons c aus e an ac tion to occur,
such as s electing a particular
function or pres enting a
supplementary dialog boxList Box – 
Allows you to select an
item from a list. Scroll bar - Us e the
scroll bar typic al ass oc iated with list
boxes to move up and down the list.
An item that is highlighted is
available f or s election.
Pop-Up Preview Windows –
 Pop-
Up preview windows are...

18
5200 User’s Manual
Auto Search & Temp Channel
Auto Search
When a new source is introduced to the
projector, the projector will initially search
through the “user
 ” channel listing for a
match. If a match is found, this channel is
selected and the channel number is
displayed in the “Chan n, Select Channel”
command button located on the initial menu.
If no match is found in the “user” channel
listings, then auto-search will look through
the “factory
 ” read-only channel data for a
match. If a match is...