Home > American Audio > CD/Mp3 PLAYER > American Audio CDMp3 PLAYER Encore 2000 User Manual

American Audio CDMp3 PLAYER Encore 2000 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual American Audio CDMp3 PLAYER Encore 2000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 120 American Audio manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							©American Audio®   -   www.AmericanAudio.us   -   Encore 2000 Instruction Manual Page 31
    MIXER SET-UP
    American Audio V4001™
    Speaker Cables
    Typical Balanced Output Set-up
    This image details a typical stereo output layout. Note the use of the Balanced XLR Jacks on both 
    the mixer and the amplifier.  Always use the balanced output jacks whenever possible. The balanced 
    output jacks should always be used for cable runs in excess of 15 feet. 
    Using the balanced jacks will ensure a clean signal through out the entire audio system. 
    						
    							©American Audio®   -   www.AmericanAudio.us   -   Encore 2000 Instruction Manual Page 32
    The crossfader is “Hot Swapable” which means it may be replaced at any time, even when power is 
    applied. Only replace with American Audio Part Feather Fader Plus. Replacing with any o\
    ther model 
    fader may seriously damage your mixer. Please, always use insulated tools. 
    Replacing the Crossfader:
    1.  Using a Phillips screw driver, unscrew the six stainless steel retainer screws that hold the mixer    
     face plate in place.
    2.  Gently remove the crossfader knob. Lift and remove the mixer face plate to access the cross   
     fader. Carefully pull the crossfader up from its seated position. 
    3.  After removing the crossfader, disconnect the ribbon cable that attaches the crossfader to the    
     PC board. Grasp the crossfader by its base and pull the ribbon cable by its connector not the \
       
     actual cables. The connector is designed to only fit one way, so don’t worry about the connec-   
     tors orientation.
    4. Unscrew the ground cable from the crossfader plate. Now unscrew the crossfader from the    
     crossfader plate and replace with the new crossfader. Connect the ground cable to the cross   
     fader plate. 
    5.  Connect the new crossfader to the ribbon cable and replace in reverse order.
     CROSSFADER REPLACEMENT 
    						
    							©American Audio®   -   www.AmericanAudio.us   -   Encore 2000 Instruction Manual Page 33
    WARRANTY INFORMATION: The ENCORE 2000 carries a ONE  year  (365  days)  limited war-
    ranty. This warranty covers parts and labor. Please fill out the enclosed warranty card to validate your 
    purchase and warranty. All returned service items whether under warranty or not, must be frei\
    ght 
    pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty, you must 
    provide a copy of your proof of purchase invoice. Please contact American Audio® customer support 
    at (800) 322-6337 for a R.A. number. All package not displaying a R.A. number on the outside of the 
    package will be returned to the shipper.
    1-YEAR LIMITED WARRANTY
    A.  American Audio® hereby warrants, to the original purchaser, American Audio® products to be free 
    of manufacturing defects in material and workmanship for a period of 1 Year (365 days) from the date 
    of purchase. This warranty shall be valid only if the product is purchased within the United States of 
    America, including possessions and territories. It is the owner’s responsibility to establish the date and 
    place of purchase by acceptable evidence, at the time service is sought. 
    B.  For warranty service, send the product only to American Audio®. All shipping charges must be 
    pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this 
    warranty, American Audio® will pay return shipping charges only to a designated point within the 
    United States. If the entire instrument is sent, it must be shipped in its original package. No acc\
    es-
    sories should be shipped with the product. If any accessories are shipped with the product, American 
    Audio® shall have no liability whatsoever for loss of or damage to an\
    y such accessories, nor for the 
    safe return thereof.  
    C.  This warranty is void if the serial number has been altered or removed; if the product is modified in 
    any manner which American Audio® concludes, after inspection, affects the reliability of the product; 
    if the product has been repaired or serviced by anyone other than the American Audio® factory unless 
    prior written authorization was issued to purchaser by American Audio®; if the product is damaged 
    because not properly maintained as set forth in the instruction manual. 
    D.  This is not a service contract, and this warranty does not include maintenance, cleaning or peri-
    odic  check-up.  During  the  period  specified  above,  American  Audio® will replace defective parts at 
    its expense, and will absorb all expenses for warranty service and repair labor by reason of defects 
    in material or workmanship. The sole responsibility of American Audio® under this warranty shall be 
    limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of 
    American Audio®. All products covered by this warranty were manufactured after January 1, 1990, and 
    bear identifying marks to that effect. 
    E.  American Audio® reserves the right to make changes in design and/or improvements upon its prod-
    ucts without any obligation to include these changes in any products theretofore manufactured. 
    F.  No warranty, whether expressed or implied, is given or made with respect to any accessory sup-
    plied with products described above. Except to the extent prohibited by applicable law, all implied 
    warranties made by American Audio® in connection with this product, including warranties of mer-
    chantability or fitness, are limited in duration to the warranty period set forth above. And no warran-
    ties,  whether  expressed  or  implied,  including  warranties  of  merchantability  or  fitness,  shall  apply  to 
    this product after said period has expired. The consumer’s and or Dealer’s sole remedy shall be such 
    repair or replacement as is expressly provided above; and under no circumstances shall American 
    Audio® be liable for any loss or damage, direct or consequential, arising out of the use of, or inability 
    to use, this product.  
    G.  This warranty is the only written warranty applicable to American Au\
    dio® Products and supersedes 
    all prior warranties and written descriptions of warranty terms and cond\
    itions heretofore published. 
     WARRANTY 
    						
    							©American Audio®   -   www.AmericanAudio.us   -   Encore 2000 Instruction Manual Page 34
     SPECIFICATIONS
    GENERAL Model: American Audio Encore 2000 - Professional DUAL CD Player/MP3        Player/2-Channel Mixer/MIDI Controller
    Type: Tray loading, digital compact disc/USB audio player.
    Disc type: Standard size compact discs only (5 in/12 cm and 3in/8cm)
          Applicable File Extenstions for Mp3s:  mp3, MP3, mP3, and Mp3
    Pitch Range: Within +/- 4%, +/- 8%, +/- 16% (+/-100% for CDDA)
    Pitch Accuracy: +/-0.15%
    Dimensions: 450mm (L) x 285mm (W) x 110mm (H)
    Installation:                          Place on flat surface or mount in flat case
    Weight: 11 Lbs. / 5 Kgs    
    Power supply:  AC 100~240V, 50/60Hz (Universal)
    Power consumption:  23W   
    Environmental conditions:  Operational temperature:  5 to 35˚C (41 to 95˚F)   
           Operational humidity:  25 to 85% RH (no condensation)     
          Storage temperature:  -10 to 60˚C (14 to 140˚F)
    Accessories: Instruction Booklet   AC Power Cord  
    MIXER SECTION
    Input/Output Impedance & Sensitivity (Level/Impedence): (Master set to 0dBV output, Load=100K 
    OHM, maximum gain, EQ Flat, Deck/Mixer SW to Mixer)
    Input Impedance & Reference Level:
    LINE:       47K OHM /-12dBV (250mV)  
    AUX:              47K OHM /-12dBV (250mV)  
    MIC:              10K OHM /-48dBV (3.98mV) 
    Output Impedance & Sensitivity:
    REC:             1K OHM /-8dBV (398mV)  +/-2dB
    MASTER:      1K OHM /+2dBV (1.25V) +/-2dB
    MASTER XLR:     300 OHM /4dBm (1.23V) +/-2dB (Between Hot & Cold)
    PHONES:      4.7 OHM /+2dBV (1.25V)  +/-2dB
    Maximum Input (1KHz, THD=1% Master Output, EQ Flat, Maximum Gain, w/20KHz LPF, A-Weighted, 
    Deck/Mixer SW To Mixer)
    LINE:             More than -2dBV (794mV)
    AUX:       More than -2dBV (794mV)
    MIC:       More than -37dBV (14mV) Maximum Gain
    Maximum Output (1KHz, THD=10% Master Output, EQ Flat, Maximum Gain, w/20KHz LPF, 
    A-Weighted, Deck/Mixer SW To Mixer)
    MASTER:            More than +11dBV (3.55V) 
    REC:               More than +1dBV (1.13V)
    PHONES:         More than +3dBV (1.42V, Load=32 OHM)
    Frequency Response (Master=0dBV output, Maximum Gain, EQ Flat, Deck/Mixer SW to Mixer)
    LINE, AUX, MIC:     20-20KHz 0+/-2dB
    THD+N - Total Harmonic Distortion: (EQ Flat, Maximum Gain, w/20kHz LPF, A-Weighted, Deck/Mixer 
    SW To Mixer):
    LINE:              Less than 0.04% 20 - 20KHz
    MIC/AUX:           Less than 0.05% @ 1KHz
    Cross Talk (Maximum Gain, EQ Flat, w/20KHz LPF, A-Weighted, Deck/Mixer SW To Mixer) 
    LINE/AUX:        More than 61dB @1KHz between L and R
           More than 100dB @ 1KHz between channels
    S/N Ratio: (Maximum Gain, EQ Flat, W/ 20KHz LPF, A-Weighted, Deck/Mixer SW To Mixer)
    LINE/AUX:      More than 100dB 
    						
    							 SPECIFICATIONS
    MIC:       More than 100dB
    Channel Equalizer: (Deck/Mixer SW To Mixer)
    BASS:                     +12 +/-2dB at 70Hz, 
                  Below -32dB at 70Hz
    MID:                      +12 +/-2dB at 1KHz, 
                    Below -32dB at 1KHz
    TREBLE:                    +12 +/-2dB at 13KHz, 
                    Below -32dB at 13KHz
    Fader Maximum Attenuation (Maximum Gain, EQ Flat, w/20KHz LPF, A-Weighted, Deck/Mixer SW To 
    Mixer)
    CHANNEL FADER:     More than 100dB at 1KHz
    CROSSFADER:     More than 100dB at 1KHz
    CHANNEL BALANCE:       Within 3dB      CD PLAYER SECTION 
    AUDIO CHARACTERISTICS (EQ Flat, Input Gain/Master/Fader Maximum)
    Output Level  +8dBV (2.51V) +/-2dB (TCD-782 TRK2, Deck/Mixer SW to Mixer)
          -2dBV (794mV) +/-2dB (TCD-782 TRK2, Deck/Mixer SW to Mixer)
    T.H.D. + NOISE Less than 0.04% (TCD-782 TRK2; W/ 20KHz LPF, A-Weighted, Deck/Mixer SW    
                   to Mixer)
    Frequency Response  17 - 20KHz, 0+/-2dB (TCD-782 TRK2,3,7, Deck/Mixer SW to Mixer)
    S/N Ratio  More than 81dB (TCD-782 TRK2,8, W/ 20KHz LPF, A-Weighted, Deck/Mixer SW   
                 to Mixer)
    Channel Separation  More than 75dB @ 1KHz (TCD-782 TRK2,9,11, W/ 20KHz LPF, A-Weighted,     
                     Deck/Mixer SW to Mixer)
    SEARCHING TIME (TEST DISC: TCD-792) 
    Short access time  Less than 4sec to next track
    Long access time  Less than 6sec from First Track to Last Track
    PLAYABILITY 
    Interruption  More than 800um (TCD-725)
    Black dot More than 600um (TCD-725)
    Finger prints More than 65um (TCD-725)
    Eccentricity More than 140um (TCD-712)
    Vertical deviation More than 500um (TCD-731R)
    PICK-UP
    System Object lens drive system optical pick-up
    Object lens drive system  2 dimensional parallel drive
    Tracking detection  3 spot beam detection
    Optical source Semiconductor laser
    Wave length 780nm
    USB HOST PLAYER SECTION: (Signal Format: MP3, 128KBPS, EQ FLAT, INPUT GAIN/MASTER/FADER 
    MAXIMUM) 
    Output Level +8dBV (2.51V) +/-2dB (TCD-782 TRK2, Deck/Mixer SW to Mixer)
          -2dBV (794mV) +/-2dB (TCD-782 TRK2, Deck/Mixer SW to Mixer)
    Frequency Response  17 - 16KHz, 0+/-2dB (TCD-781 TRK1,4,16, Deck/Mixer SW to Mixer)
    T.H.D. + NOISE Less than 0.04% (TCD-782 TRK2; W/ 20KHz LPF, A-Weighted, Deck/Mixer SW    
                   to Mixer)
    S/N Ratio  More than 81dB (TCD-782 TRK2,8, W/ 20KHz LPF, A-Weighted, Deck/Mixer SW   
                 to Mixer)
    LR Separation  More than 75dB @ 1KHz (TCD-782 TRK2,9,11, W/ 20KHz LPF, A-Weighted,     
                     Deck/Mixer SW to Mixer)
    ©American Audio®   -   www.AmericanAudio.us   -   Encore 2000 Instruction Manual Page 35 
    						
    							USB SLAVE PLAYER SECTION: (Signal Format: MP3, 128KBPS, EQ Flat, INput Gain/Master/Fader 
    Maximum, Deck/Mixer SW To Mixer, MIDI Set-Up, Mix-Mixer) 
    Output Level +14dBV (5.02V) +/-2dB (TCD782 TRK2)
    Frequency Response  17 - 16KHz, +/-2dB (TCD781 TRK1,4,16)
    T.H.D. + NOISE Less than 0.04% (TCD781 TRK1, W/20KHz LPF, A-Weighted)
    S/N Ratio More than 100dB (TCD782 TRK2,8, W/ 20KHz LPF, A-Weighted)
    LR Separation More than 75dB @ 1KHz (TCD782 TRK2,9,11, W/ 20KHz LPF, A-Weighted)
    RECORDING & PLAYBACK: (Line 1KHz, -12dBV Input, Gain Maximum)
    Output +2dBV (1.25V) +/-2dB
    THD+N Less Than 0.07% (Gain Maximum, w/20KHz LPF, A-Weighted)
     SPECIFICATIONS
    NOTES: Specifications and improvements in the design of this unit and this manual are subject to 
    change without any prior written notice.
     MP3  FO RMA T 
    Applicable file  extension s  mp3 . MP3  . mP3  . Mp3  
    ISO9660 max. 63 cha racters 
    Joliet max.  63 c haracters 
    CD-ROM  sector  format  mode-1 only 
    Max. numbe r of  Folders  255
    Disc Format 
    Max. numbe r of  files  max. 999 files  (* note  #1) 
    File System    FA T  12/16/32 
    Applicable  file  extension s  mp3. MP3.  mP3. Mp3 
    Max. numbe r of  Folders  999
    USB Format 
    Max. numbe r of  files  max. 999 files   
    MPEG  1 Layer  3 stand ard  (ISO/IEC 
    11172-3),  which  provides for  sing le 
    c hannel  (ʻmonoʼ)  and  two-chann el 
    (ʻstereoʼ)  co ding  at sampling  rates of 
    32, 44.1 and  48kHz.  32/
    40/48/56/80/ 96/112/ 128/ 160/192/
    224/256/320  kbps 
    Xing/VB RI VBR 
    MPEG  2 Layer  3 stand ard  (ISO/IEC 
    13818-3),  which  provide s for  similar  
    coding  at sampling  rates  of 16, 
    22.05 and 2 4 kHz.  32/
    40/48/56/64/ 80/96/112/ 144/ 160 
    Kbp s 
    Xing/VB RI VBR 
    MP3  Format 
    MPEG 2.5 Layer  3 standard,  which 
    pr ov ides  for   sim ilar  coding  at 
    sampling  ra tes  of 8, 11.025  and 12 
    kHz. 32/
    40/48/56/64/ 80/96/112/ 144/ 160 
    Kbp s 
    Xing/VB RI VBR   
    Disc  at Onc e and  Track  at Onc e   Disc Writing  Met hod 
    Multi Sessio n  If 
    the  1st session  is CDDA,  you can 
    playback  Only CDDA  tr ack,  If the  1st
    sessio n is  MP3,  you can  playback 
    only  MP3  file. 
    ©American Audio®   -   www.AmericanAudio.us   -   Encore 2000 Instruction Manual Page 36 
    						
    							©American Audio® World Headquarters:
    6122 S. Eastern Ave. Los Angeles, CA 90040 USA
    Tel: 323-582-3322  Fax: 323-582-3311
    Web: www.AmericanAudio.us  E-mail: [email protected]
    American DJ Europe
    Junostraat 2
    6468 EW Kerkrade
    Netherlands
    [email protected] / www.americandj.eu
    Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99 
    						
    All American Audio manuals Comments (0)

    Related Manuals for American Audio CDMp3 PLAYER Encore 2000 User Manual