Alpha Tool.Com.HK Limited Polisher VSP110 User Manual

Part No:  VSP-110 / VSP-220 
Alpha
®
 Variable
Speed Polisher
Instruction Manual
MANUAL
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
www.alpha-tools.com 

2
TABLE OF CONTENTS
Introduction ...................................................................................................................3
  About the Symbols ................................................................................................ 3
Safety Instructions ........................................................................................................ 3
  For Safe Operation...

3
INTRODUCTION
Thank you for purchasing the Alpha® Wet Polisher.  Please read this instruction manual 
thoroughly to ensure safety and correct use of the polisher.  Keep this manual in a place 
where operators can access it easily whenever necessary.
 ABOUT THE SYMBOLS
According to the hazard level, all safety notes in this manual are classifi ed into “DANGER”,  
“WARNING”, and “CAUTION”.
  DANGER!  Death or serious personal injury is imminent when handling this 
polisher incorrectly.
  WARNING!  There is...

4
2. Consider work area environment
  Do not expose power tools to rain. Do not use power tools in damp or wet locations 
without GFCI protection.  Keep work areas well lit. Do not use the tool in presence of 
fl ammable liquids or gases.
3.  Guard against electric shock
  Prevent body contact with grounded surfaces. For example: pipes, radiators, ranges, 
and refrigerator enclosures; use grounded outlets. 
4.  Keep children and visitors away
  Do not let visitors contact tool or extension cord.  All...

5
15.  Remove adjusting keys and wrenches
  Check to see that keys and adjusting wrenches are removed from the tool before 
turning it on.
16. Avoid unintentional starting
  Do not carry a plugged-in tool with fi nger on switch. Be sure the switch is off when 
plugging in.
17.  Outdoor use extension cords
  When tool is used outdoors, use only extension cords intended for use outdoors and 
so marked.
18. Stay alert
  Use caution and do not operate tool when you are tired or on medication.
19.  Check for...

6
ADDITIONAL PRECAUTIONS FOR USING THE VSP-110
In addition to the general safety notes described on the preceding pages, please read and 
observe the following precautionary notes before using the polisher.
  DANGER!
1.  Check the working voltage.
  Be sure the voltage available at power outlet matches specifi ed voltage on the name-
plate.  If the polisher is used with higher voltage than specifi ed, the motor will burnout.  
Any attempts to do so may damage the polisher or cause an accident or injury....

7
  WARNING!
10.  Attach the backer pad and polishing disc correctly by following the procedure 
in this instruction manual.
  Attaching the polishing discs incorrectly may cause an accident.
11.  Observe any suspicious abnormal noises when a polishing disc is attached for 
the fi rst time and polisher is turned ON.
It may cause bodily injury if the polishing disc fl ies off.
12.  Do not touch the polishing disc while spinning.
  The polishing disc spins very fast and you may hurt  yourself.
  
13.  Be...

8
  PREPARATION BEFORE OPERATION
1. GFCI Information.
– Since the Alpha
® Wet Polisher is designed with  double insulation, an in-line GFCI is 
provided as a standard accessory. For your safety and to prevent possible electric 
shocks, it is strongly advised to test the GFCI on a regular basis.
  Note:  The GFCI must be used for your safety when this polisher is 
used anywhere in a damp environment,  when used with water, or 
when it is used on   metal plates, steel frames or platens.
Never attach a...

9
VSP-110 OVERVIEW
Speed Adjuster
Power Switch
In-line GFCI
Garden Hose AdapterWater Line
Center Water Feed “C” Handle
Water Valve
  SPECIFICATIONS
Working Power Supply ................................................... Single-phase AC, 50/60 Hz
Voltage ........................................................................... 110V / 220V
Plug Type ....................................................................... A (110V) / C (220V)
Amperage...

10
 ACCESSORIES
STANDARD ACCESSORIES:
1. Side Handle
2. Wrench
3.   Spare Set of Carbon Brushes