Alpha Tool.Com.HK Limited Adapter WBCKIT User Manual

Part No: WBCKIT
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
www.alpha-tools.com
Alpha
® 
Wet Blade
Cutting Kit
Instruction Manual
MANUAL
HSG-125
®
Blade Guard Coolant Tube
Garden Hose Adapter  GFCIHook & Loop Strap
*Tool and Blade sold separately
Water Line 

2
TABLE OF CONTENTS
 SERVICE
Use only Alpha Professional Tools® accessories and spare parts.  Should 
components which have been described need to be exchanged, please contact 
your dealer or Alpha Professional Tools
®.
 NEED MORE INFORMATION
For information on Alpha Professional Tools® complete product line, visit us on the 
web at www.alpha-tools.com.
CONTENTS
Parts List .............................................................................................. 3
Instructions...

3
1
2
3 4
56
7
8
 PARTS LIST
No. Item Description Part Number
1. Protective Guard for HSG-125
The WBCKIT can also be attached to 
other grinders with minimal alteration 
to their safety guards140007
2. Water Line (10’) 3m*
133287
3. Garden Hose Adapter*
4. Ground Fault Circuit Interrupter GFCI-1
5. Hook & Loop Strap 140003
6. Coolant Tube 140004
7. 90 degree Swivel Fitting 140005
8. Plastic Ties PDH-CABLETIES
9. Plastic Wire Wrap 140002
* Not sold separately.
9
 INSTRUCTIONS
Alpha Professional Tools®...

4
 ASSEMBLY OF WBCKIT GUARD
1.  Thread plastic cable tie through 
holes in the guard.  (If using another 
grinder the safety guard must be 
altered to accomodate cable ties 
as shown above). 
STEP 2
STEP 3STEP 4
2.  Place coolant tube between holes 
on Guard and tighten in place with 
plastic tie.
3.  Repeat steps 1 and 2 to com-
pletely secure the coolant tube to 
the guard.4.  Trim plastic ties with pliers as shown 
above.
WBCKIT Guard Assembly
STEP 1
Hole Size: 
5mm or #8 Drill Bit
10mm (3/8”)
25mm...

5
 INSTALLATION OF WBCKIT GUARD
Note: It is important to securely attach the 
WBCKIT to the tool.
1.  Before tightening, slide the protective cover 
onto clamping collar so that the lip on the 
protective cover fi ts into the groove on the 
tool.
2.  Position the protective cover with the 
shield facing backwards.  Push down 
until the protective cover is fi rmly seated 
on the clamping collar.
3.  Tighten the clamping screw to a snug fi t.  
The protective cover should not be able 
to move.
4.  Take one...

6
3.  Position hook & loop strap 
around the waterline and grind-
er body.
Note: Position the strap away 
from the vent ports of 
grinder.
4.  The 90 degree swivel fi tting 
can be moved to give a tight 
installation to the grinder 
body.
5.  Adjust the strap to a tight position. 2.  Tighten the compression nut with a 
14mm wrench to a secure condition.
Note:  Do not overtighten connection.
If leakage occurs during startup, 
tighten in small increments until a 
leak tight connection is made.
 GARDEN HOSE...

7
 COMPLETED ASSEMBLY
1.  Install the plastic wire wrap 
around both power cord and 
water-line as shown.
 INSTALLATION OF GFCI
1.  Install the GFCI to the grinder 
power cord as shown.  Con-
nect to power and check the 
GFCI for proper function by 
pressing the test and reset 
buttons.
Caution:  Do not operate  a 
grinder with a water-feed sys-
tem, without a GFCI installed 
and in proper working condition. 2.  Finish the wrapping proce-
dure until secure.
 INSTALLATION OF 
PLASTIC WIRE WRAP

 

Copyright © 2009 Alpha Professional Tools. All rights reserved. 
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
www.alpha-tools.com