Alpha Tool.Com.HK Limited Adapter EZ TCutter User Manual

Part No:  KEC-600Version 1
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14
www.alpha-tools.com
Alpha® EZ Thin Panel
T-Cutter Manual
MANUAL 

2
1 Bolt8Cutting Head
2 Threaded Pin 9Scale Indicator
3 Cap Nut 10 Rubber Cap
4 Scaled Bar 11Two-Holed Washer
5 Roller Housing 12Oil Reservoir Cap
6 Guide Rollers 13 Rubber Handle
7 Cutting Head Holder 14Fixation Screw
TaBle OF CONTeNTS
Introduction ........................................................................\
................................ 3
About the Symbols   ........................................................................\
.................... 3
General Safety Instructions...

3
Thank you for purchasing the Alpha® EZ Thin Panel T-Cutter.  Please read this 
instruction manual thoroughly to ensure safe and correct use of the EZ T\
hin Panel 
T-Cutter. Keep this manual in a place where operators can access it easily whene\
ver 
necessary.
 ABOuT THE SymBOlS
according to the hazard level, all safety notes in this manual are classified into 
“DANGER”,  “W ARNING”, and “CA u TION”.
  DANGER! Death or serious personal injury is imminent when handling this 
T-Cutter incorrectly....

4
1
11
10
3
4
12
13
2
56
9
914
7
8
10
DETAIL “B”
 DETAIL “A”
“A”
“B”
 ASSE m B ly INSTR u CTIONS
1. Set the  scaled  bar  (4)  onto  the  pre-mounted  bolt  (2)  of  the  roller  housing  (5). 
m

ake sure that the rollers in the roller housing are in the correct posit\
ion as the 
picture. (Detail “A”)
 *Tip: See page 7 for instructions on replacing the guide roller.
2. Fasten the bolt (1) and the cap nut (3). The 2-hole washer (11) should be placed  as the schematic indicates.
 
 
*Tip: Check if the...

5
KEC1901KEC1902
REPlACEmENT PARTS
PART NO. DESCRIPTION
KEC1901 Cutting Head Holder
KEC1902 Cutting Head
KEC1903 Guide Roller (1 Pack= 20 Pieces)
KEC1904 Assembly Hardware
KEC1905 Roller Housing
KEC1906 Scaled Bar
KOC1000 EZ Cutter Oil
KEC1905KEC1906
KEC1903
KEC1904
1.  r emove the oil reservoir cap (12) and fill the 
reservoir (12) with 
a
 lpha® EZ Cutter Oil.  
(See Figure -1)
Note:  Tighten reservoir cap after filling with oil.
 HOW TO OPERATE
Figure-1
EZ Cutter Oil   

6
2. Check if the red scale indicator (9) is facing 
towards the roller housing (5).  
(See Figure 2)
 
 
Set the distance of score required by sliding 
the cutting head holder (7), the red indicator 
defines the width of score on the scale 
bar(4). 
3.
 
Place the roller of the roller housing (5) 
against the edge of the tile and put the 
cutting head (8) onto the tile to be cut. Grab 
the rubber handle (13) to have a safe and 
comfortable cut. (See Figure-3 and 4)
Note:  (a) Loosen the reservoir cap...

7
6. m ETHOD TWO:  m anually snap the material to 
complete the process.  (See Figure-6)
TIP: Material that will be snapped will need to hang over the 
edge of the table prior to performing the “snap method”.  (See 
Figure 6)
 NOTE:  If thin material has fiber glass on the back 
surface, you will need to use a razor blade to cut the fiber 
glass after the material has been scored and snapped.  
(See Figure 7)
7. When cutting is complete, the sharp edges become 
a safety hazard. 
you can easily smooth out...

Copyright © 2014 Alpha Professional Tools. All rights reserved. 
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14
www.alpha-tools.com
07/2014