AllTrade Kawasaki 8in Drill Press 840116 User Manual

Ensure 
that 
the 
switch 
toggle, 
when 
removed, 
is 
kept 
in
a secure 
place. 
Once 
removed, 
the 
drill 
press 
will 
not 
start 
without 
it.
ADJUSTING 
THE 
WORK 
TABLE
1.The 
worktable 
(1) 
can 
be 
raised 
or 
low-
ered 
on 
the 
drill 
press 
column 
(2) 
by
loosening 
the 
table 
clamp 
(3). 
See
Figure 
12.
2.After 
the 
table 
is positioned 
at 
the
desire 
height, 
LOCK 
the 
table 
in 
place
by 
tightening 
the 
table 
clamp 
(3). 
NOTE:
Final 
positioning 
of 
the 
table 
should
always...

1. 
Lift 
up 
the 
pulley 
cover 
(1).
2. 
Release 
the 
belt 
tension 
by 
loosen-
ing 
the 
tension 
lock 
knob 
(2) 
located
on 
the 
side 
of 
the 
drill 
press 
head.
Loosen 
the 
tension 
lock 
knob 
(2) 
by
turning 
it counter
clockwise.
3. 
Pivot 
the 
motor 
(3) 
towards 
the
front 
of 
the 
drill 
press.
4. 
While 
holding 
the 
motor 
pivoted 
to
the 
front 
of 
the 
drill 
press, 
position
the 
belt 
(4) 
on 
the 
desired 
step 
of
the 
motor 
pulley 
(5) 
and 
the 
spindle
pulley 
(6). 
See...

3. 
Turn 
the 
spring 
housing 
(5) 
counter-
clockwise 
to 
increase 
the 
spring 
ten-
sion 
or 
clockwise 
to 
decrease 
the
spring 
tension.
4. 
Turn 
nut 
(4 
- inside) 
until 
it contacts
the 
spring 
housing 
(5). 
Back 
nut 
(4)
out 
1/4 
turn 
and 
tighten 
it against
nut 
(3 
- outside) 
to 
hold 
the 
spring
housing 
in 
place.
5. 
IMPOR
TANT
:The 
inside 
nut 
(4)
should 
not 
touch 
the 
spring 
housing
(5) 
after 
it has 
been 
tightened.
CORRECT 
DRILLING 
SPEEDS
The 
correct 
drilling...

Always 
attach 
grounded 
(3-prong) 
extension 
cords 
to 
grounded 
(3-hole) 
outlets.
If the drill press must be used outside, use an extension cord labeled “W-A” or “W.”
These extension cords are rated for outdoor use and reduce the chances of electrical shock.
If you 
must 
use 
an 
extension 
cord, 
be 
sure 
that 
the 
gauge 
is large 
enough 
to 
carr
y
the 
amount 
of 
current 
necessar
y for 
your 
power 
tool.
If not, 
your 
tool 
may 
experi-
ence 
a loss 
of 
power
, excessive 
voltage 
drop...

Warranty 
Performance 
By 
pur
chasing 
the 
product, 
pur
chaser 
expressly 
acknowledges 
and 
agrees 
that 
their
sole 
and 
exclusive 
remedy 
under 
this 
warranty 
shall 
be 
strictly 
limited 
to 
the 
repair
or 
replacement 
of 
any 
covered 
nonconforming 
items 
or 
parts 
thereof 
provided 
that
any 
such 
nonconforming 
item 
and/or 
part 
is promptly 
returned 
to 
Alltrade’
s facility
postage 
pre-paid 
and 
insured 
(address: 
ALL
TRADE 
Warranty 
Claims 
& 
Repair
, 
1431 
Via 
Plata,...

ALL
TRADE 
AND/OR 
ITS 
REPRESENT
ATIVE(S), 
OR 
THE 
PURCHASER, 
INCLUDING
BUT 
NOT 
LIMITED 
TO 
THE 
IMPLIED 
WARRANTY 
OF 
MERCHANT
ABILITY 
AND 
THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED 
AND 
DISCLAIMED 
BY 
ALL
TRADE 
AND/OR 
ITS 
REPRESENT
ATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH 
WARRANTIES 
AND 
RIGHTS, 
CLAIMS 
AND/OR 
CAUSES 
OF 
ACTION 
ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE 
REMEDY 
IS 
AS 
ST
ATED...