Aleratec Wall Mount for Charge and Guard Secure ChargeSync Cabinet 16 User Guide

							INSTALLATION GUIDE
Aleratec  
Wall Mount for Charge and 
Guard Secure Charge/Sync  Cabinet 16™
Part No. 400107  
						

							www.aleratec.com
Copyright/Model Identification
The content of this manual is for informational purposes only and is subject 
to change without notice. 
This manual is copyrighted with all rights reserved. Under copyright laws, 
this manual and the software described within may not be copied, except in 
the normal use of the product(s) described within or to make a backup copy.
Copyright© 2014  
Aleratec, Inc.
9851 Owensmouth Avenue
Chatsworth, CA 91311 U.S.A.
www.aleratec.com
Aleratec
® is a registered trademark and Charge and Guard Secure 
Charge/Sync Cabinet 16 ™ is a trademark of Aleratec, Inc. 
Check out Aleratec Online!
•	google.com/+AleratecInc
•	 YouTube.com/Aleratec
•	 Twitter.com/Aleratec
•	 Facebook.com/Aleratec
•	 Blog.Aleratec.com
Please record the following information to help expedite any warranty 
claim:
Model No. 400107
Date Purchased   ________________________________________________  
Place of Purchase   ______________________________________________  
						

							www.aleratec.com1
Introduction
Thank you for purchasing the Aleratec Wall Mount for Charge and Guard 
Secure Charge/Sync Cabinet 16. Please read this Installation Guide 
thoroughly before using this product. 
 
Product Features
• Safely secures cabinet to the wall
•  Preserves precious floor/table space
•  Heavy-duty construction and materials
 
Included Items
 
Safety 
 
WARNING:  Make sure that you consult with appropriate engineering, 
architectural or construction professional to ensure that your Aleratec 
mounting solution is mounted properly to handle applied loads.  
 
CAUTION:  Make sure the wall mount bracket is level, flush and snug to 
the wall surface. DO NOT OVERTIGHTEN THE BOLTS. 
 
CAUTION:	DO	NOT 	EXCEED	MAXIMUM	LISTED	 WEIGHT	
CAPACITY.	SERIOUS	INJURY 	OR	PROPERTY	DAMAGE	MAY	
OCCUR! Bottom Bracket
Top Bracket
Paper Mounting Template
(2) Security Screws
Registration Card
Installation Guide 
(this document)  
						

							www.aleratec.com
2
Introduction
Tools Needed
 
You will also need mounting hardware such as bolts, screws, washers, etc to 
mount the brackets and additional tools for the mounting hardware chosen.   
 
Suggestions for different methods of mounting:
 
Brick wall: 
                5/16” x 3” Concrete anchor bolts
                5/16” Washers
                1/4” Concrete drill bit
Drywall:
                1/4” x 3” Toggle bolts 
                1/4” Washers 
                3/4” Drill bit
Stud:
                5/16” x 2.5” Lag screws
                5/16” Washers
                15/64” Drill bit
 
Please consult with an appropriate engineering, architectural or 
construction professional to choose the appropriate mounting 
hardware.   
						

							www.aleratec.com3
Introduction
Mounting Considerations  
 
Space Requirements:  
						

							www.aleratec.com
4
Introduction
Wood Stud Wall Mounting Option    
 
Studs can be positioned in one of four mounting options. While the first 
option (studs on either side) is recommended, you should consult with a 
construction professional to confirm which method is best suited for your 
particular situation. After you decide on a hole option, follow attachment 
instructions on the following pages.
Important – Wall brackets must be secured to the wall using all 6 mounting 
holes using appropriate hardware for the wall surface. DO NOT mount to 
drywall without at least one stud to support both brackets. For mounting 
to a brick wall, consult with an appropriate engineering architectural or 
construction professional. 
Option 1   
RECOMMENDED 
Studs on either side
Option 2   
One stud in the center
Option 4  
One stud on the left side
Option 3  
One stud on the right side  
						

							www.aleratec.com5
Installation
Wood Stud Wall Mounting
1. Find stud and draw a mark.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.  Place template on wall lining up the chosen hole with the stud at the 
desired height.  
						

							www.aleratec.com
6
Installation
Wood Stud Wall Mounting - Continued
3.  Secure template to wall and check to ensure it is level.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4.  Use the appropriate drill bit(s) to drill the three holes for the top bracket 
that correspond with the hole markers on the paper template.  
						

							www.aleratec.com7
Installation
Wood Stud Wall Mounting - Continued
5. Use the appropriate drill bit(s) to drill the bottom three holes.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
6.  Remove paper template from the wall.  
						

							www.aleratec.com
8
Installation
Wood Stud Wall Mounting - Continued
7.  Secure the top bracket with your chosen mounting hardware. Verify wall 
bracket is level before tightening screws.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
8.  Repeat step 7 for the bottom bracket.