Aleratec Charge and Guard Secure ChargeSync Cabinet 16 User Guide

www.aleratec.com7
Setup
Installing Your Cables - Continued
2. Plug the USB A/M end of your cable into one of the USB ports within 
the cabinet. If using the numbering labels, make sure your cable number 
corresponds to the port number.
 
 
3. Wind each cable around the cable management posts to take up any 
excess slack. Note: Two winds should be sufficient for a standard 
1 meter (3.3 ft.) cable.
 
 
 
 
 
 
 
 
 
 
   

www.aleratec.com8
Setup
Installing Your Cables - Continued
4. Once the proper length has been established, insert a zip-tie through the 
platform holes.
 
 
 
 
 
5. Secure the cable winding in place. 
 
 
 
 
 
 
 
 
 
 
 
   

www.aleratec.com9
Setup
Installing Your Cables - Continued
6. Thread the cable down through the appropriate guide slot.
 
 
 
 
7. Clip cable to roof clips. 
 
 
 
 
 
 
 
 
 
 
 
   

www.aleratec.com10
Setup
Installing Divider Walls
Setting up the tablet dividers (17) in your Charge and Guard Secure Charge/
Sync Cabinet 16.
1. Insert each divider into a cabinet divider slot and repeat for all 17 
dividers. Note: Set up the charge/sync cables before installing the tablet 
dividers. 
 
 
 
2. Install the divider stability bar. 
 
 
 
 
 
 
 
 
 
 
 
   

www.aleratec.com11
Setup
Powering the Cabinet
Setting up the power connection to your Charge and Guard Secure Charge/
Sync Cabinet 16.
1. Make sure the power switch is in the OFF position.
 
 
 
2. Plug in the appropriate end of the power cord into the side of the unit 
and the other end into a 120V 3-prong power. 
 
 
 
 
 
 
 
 
 
 
 
   

www.aleratec.com12
Using the Charge and Guard Secure
Charging or Syncing Your Devices 
1. If syncing, use the USB A/M to B/M cable provided and connect the 
USB B end to the unit. Connect the USB A end to your host computer. 
Unplug this USB cable if charging your tablets. 
 
 
 
 
 
 
 
 
 
 
 
Sync times will vary greatly depending on a variety of factors 
including, but not limited to,  your computer and the amount of 
data being synced.  After syncing, eject each device individually as 
approprite on...

www.aleratec.com13
Using the Charge and Guard Secure
Charging or Syncing Your Devices - Continued
3. Connect each tablet or other USB-charged device to its corresponding 
charge/sync cable. 
 
 
 
 
 
 
4. Turn ON cabinet.
 
 
   

www.aleratec.com14
Using the Charge and Guard Secure
Securing Your Cabinet
1. Use the anchor loop to chain the cabinet to a secure structure. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2. In additon to the integrated locks, secure the front door with the two 
padlock loops on the front handles. 
 
*Padlock and chain not included with purchase.
*Padlock not included with purchase.  

www.aleratec.com15
iOS Device and iTunes Configuration Tips 
This station can be used with iTunes for synchronization and management of 
iPads and other iOS devices. For this and any other application (on Windows, 
Linux, etc.) this station acts as a USB hub. While these instructions are specific to 
iPads, virtually the same steps can be used for iPhones and iPod Touch devices.
Please note that this station only serves as a pathway for communication between 
your devices and the computer. Actual...

www.aleratec.com16
iOS Device and iTunes Configuration Tips - Continued
2. Click the Devices Tab and make sure “Prevent iPods, iPhones, and 
iPads from syncing automatically” is unchecked.