Aleratec 17 Bluray DVD CD Tower LightScribe Publisher SLS User Guide

							www.aleratec.com55
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Disadvantage:
 ▪The loading time may have an impact on overall duplication time for small 
duplication jobs.
 ▪The Master Disc will be loaded to the reserve partition in the Hard Drive 
temporarily until a new master is loaded and overrides the previous image. 
In comparing this duplication mode with the traditional “Duplication from 
Hard Drive” process, it offers the user more simplicity. By selecting the 
“Load and Copy” mode via one simple touch, all the necessary tasks will 
be automated for you and loaded on to the “Reserved” partition. You can 
rename the data on the “Reserved” partition and place it in a standard 
partition if you wish to keep it. (This must be done prior to loading a new 
master through “Load and Copy)”.
By default, the duplication mode is set to “Auto”. This will prompt you to choose 
between one of the duplication modes when you enter any of the following 
functions: “Copy”, “Test”, “Test + Copy”, and “Copy + Compare”.
However, if you prefer not to be prompted each time, you can always go to “14. 
Setup” and select sub-menu 9 and manually reset it. To do so, preform the following 
steps:
1. Turn on the duplicator. After the bootup is complete, you will see the following 
display:
2. Press the UP or DOWN button consecutively until you see following display:
3. Press ENT button once. You will see the following display:
4. Press the UP or DOWN button consecutively until you see following display:
Aleratec 1.001. COPYCOPYUSBPRINTSOURCE
ESCENT


Aleratec 1.0014. Set\fpCOPYUSBPRINTSOURCE
ESCENT


Set\fp1. Lang\fageCOPYUSBPRINTSOURCE
ESCENT


Set\fp9. D\fplication Mode\BCOPYUSBPRINTSOURCE
ESCENT

                  
						

							www.aleratec.com56
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Introd\fction to D\fp\Blication Mode - continued 
5. Press the ENT button once. You will see the following display:
6. Press the UP or DOWN button consecutively to select your desired mode.
7. Press the ENT button once to submit your selection. You will see the following 
display:
8. Press ESC button once to go back to the main menu. 
D\fplication Mode:A\ftoCOPYUSBPRINTSOURCE
ESCENT


Set\fp9. D\fplication Mode\BCOPYUSBPRINTSOURCE
ESCENT


D\fplication Mode:Load and CopyCOPYUSBPRINTSOURCE
ESCENT


D\fplication Mode:On the FlyCOPYUSBPRINTSOURCE
ESCENT


D\fplication Mode:PromptCOPYUSBPRINTSOURCE
ESCENT

                      
						

							www.aleratec.com57
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Using AUTOCOPY
The “Autocopy” function allows you to copy from Disc to Disc automatically 
without pressing any keys. It is the simplest way to make BD/CD/DVD copies.  
The following tutorial will show you how to use this feature.
1. Use the UP or DOWN arrow button to navigate to the following screen.
2. Press the ENT button to enter the “Autocopy” mode. You will see the following 
display:
3. Insert your Master Disc into the top Reader Tray and your blank discs into 
corresponding Writer Trays. Close the trays after you load the discs. (You can 
automatically close all trays by pressing ENT when the display shows “Waiting 
for Blanks”.)
4. Allow 5-10 seconds for the duplicator to detect your Master Disc and Blank 
Discs. After all the discs are recognized, you will see the following display:
5. After 2 or 3 seconds of processing time, the following Copy Progress Screen 
will appear.
“4012MB” indicates the capacity of the Master Disc.
“481MB” indicates the current progress of the duplication in terms of MB
“12%” indicates the current progress of the duplication.
“0” indicates that you have made 0 copies so far.
Aleratec 1.0017. A\ftoCopyCOPYUSBPRINTSOURCE
ESCENT


AUTOCOPYWaiting for MasterCOPYUSBPRINTSOURCE
ESCENT


Processing... Please WaitCOPYUSBPRINTSOURCE
ESCENT


Copying...  4012MB0 12%  481MBCOPYUSBPRINTSOURCE
ESCENT

                      
						

							www.aleratec.com58
Stand-Alone Tower P\fblisher SLS: \BT\ftorials
Using AUTOCOPY - continued 
Note: It is normal \Bto see the progress i\Bndicator stay at 0-1\B0%  
and at 100% for ap\Bproximately 30 secon\Bds d\fring CD d\fplica\Btion. 
Additionally it is n\Bormal to see the pr\Bogress indicator stay\B at 
0-10% and at 100% \Bfor \fp to 1 min\fte \Bd\fring D\bD d\fplicati\Bon. 
There is a delay ca\f\Bsed by the initializ\Bing and finalizing \Bstage of 
disc d\fplication. D\f\Be to this delay, it is normal to se\Be progress 
indicators stay at 1\B00% for \fp to severa\Bl min\ftes before mov\Bing 
on. Once the disc d\B\fplication is comple\Bted, s\fccessf\fl copies\B will 
be ejected and yo\f \Bwill see the follow\Bing display:
Next, refill your blank Discs to continue making more copies. If you wish to 
copy a new Master Disc, remove the old master and load the new Master Disc 
prior to loading any new blank discs into the Writer Trays.
Note: Failed di\bc\b will no\bt be ejected automa\btically. You will need to 
manually eject the\b\be. Throw away any fail\bed write-once di\bc\b.\b
“PASS 7” indicates that you’ve just made 7 successful copies.
“FAIL 0” indicates that you have no failure in this run.
“7” indicates that you’ve successfully copied 7 copies so far.
PASS  7  FAIL  0 (       7)Waiting for BlanksCOPYUSBPRINTSOURCE
ESCENT

         
						

							www.aleratec.com59
Men\f Overview
Men\f Overview
1.	Copy
This menu will guide you to make BD/DVD/CD copies. Before you enter this 
menu to copy, please make sure you have selected the correct Source drive. 
2.	Print
This menu will guide you to burn LightScribe labels.  Before you enter this 
menu to print, please make sure you have selected the correct Source drive.
3.	Copy	+	Print
This menu will guide you to make BD/DVD/CD copies and burn LightScribe 
labels.  When the BD/DVD/CD copies are finished, flip the discs over in the 
recorders and the menu will guide you to select a label and initiate the printing 
function.  Before you enter this menu copy and print, please make sure you 
have selected the correct Source drive.
4.	Test
This menu will guide you to make simulation of copying process. During this 
simulation process, all write once recordable discs such as (BD-R, DVD-R, 
CD-R) will be reusable. The purpose of performing such simulation is to ensure 
error free duplication.
*Warning: Due to the phy\bical \blimitation of DVD+R/RW, you can 
not perform thi\b pr\bocedure if your rec\bordable di\bc\b are DVD+\bR/RW  
recordable format. \bIf you do \bo, you w\bill encounter failu\bre me\b\bage\b.
Warning: If you are u\bing CD-\bRW/DVD-RW di\bc\b a\b your blank\b\b media 
during the \bimulatio\bn, all of the cont\bent in\bide tho\be di\bc\b\b will be era\bed 
permanently.
5.	Compare
This menu will guide you to perform a bit-by-bit comparison between the 
Master Reading Source and all the copied discs inside the Writer Tray. The 
purpose of the Compare function is to ensure that all of your copies have 
exactly same information as your Master Reading Source.  
						

							www.aleratec.com60
Men\f Overview
6.	Test	+	Copy
This menu will guide you to perform a simulation of the copying process. If 
everything passes the simulation, the copying process will be performed. If 
there’s an error encountered during the simulation, an error message will be 
displayed and the copying process will not be initiated.
7.	Copy	+	Compare
This menu will guide you to make copies and automatically perform a bit-by-
bit comparison between the Master Reading Source and all the copied discs 
inside the Writer Tray.
8.	Select	Burn	Speed
This menu will guide you to adjust the duplication speed in various duplication 
modes. 
9.	Select	Source
This menu will guide you to set the Master Reading Source. 
10.	Erase
This menu will guide you to erase your rewriteable discs in the Writer Tray. 
There are two options to erase your rewriteable discs:
a. Full Erase: It will erase the entire disc which will make it impossible to be 
recovered.
b. Quick Erase: It will erase the index of the rewriteable disc, not the data 
section.
11.	 Hard	Drive	Setup
This menu will guide you to perform various Hard Drive related operations 
such as Loading, Renaming, or Deleting your images. 
12.	 Print	Setup
This menu has the utilities for setting up a print job and managing labels.
 ▪Load Label
 ▪Rename Label
 ▪Delete Label
 ▪Print Surface Info
 ▪Label Info
 ▪Select Loading Drive  
						

							www.aleratec.com61
Men\f Overview
13.	Mix	Audio	 Tracks
This menu will guide you through the “Mix Audio Tracks” feature. This feature 
helps you combine audio tracks from various CDs into a single customize audio 
CD. 
14.	Setup
14.1 Language
This setting allows you to choose which language you prefer to navigate 
this duplicator. Current supported languages are Spanish, and English.
14.2 Auto Start
This setting allows you to choose Auto, Full or Off.
When full is selected this feature will allow the duplicator to copy 
automatically once your Master Disc and all of the Writer Trays of the 
duplicator are filled with recordable media.
When it is Off, the copy process requires you to press ENT button to 
confirm the duplication.
If , for example, your duplicator has detected 3 blank discs on a 4 tar get 
or higher duplicator and doesn’t detect any additional blank discs for 30 
seconds, the duplication will be started automatically.
In order for this feature to take effect, you need to be inside the operation 
menu such as COPY, TEST, TEST+COPY, COPY+COMPARE, etc.
14.3 Read Error Skip
Normally, when the duplicator encounters a reading error while reading 
your Master Disc, all the duplication will be aborted and all the recordable 
media will be ruined. However, if you believe that your Master Disc has 
a small, insignificant error due to physical damages, you can enable the 
setting to allow the duplicator to skip any read error* it has encountered.
*This function will not fix the error; it will only skip it to make the rest of 
the data readable.  
						

							www.aleratec.com62
Men\f Overview
14.	Setup - continued
14.4 CD Writing Mode
This setting allows you to select which mode you can duplicate a CD 
with. There are two different modes, “Disc at Once” and “Track at Once”. 
Unless you understand completely what they mean, we strongly suggest 
you to set it as “Disc at Once”.
14.5 Max Audio, VCD & CDG Speed
This setting allows you to adjust the maximum duplication speed for 
Audio and Video CD. Audio CD’s and Video CD’s do not have internal 
error checking capability, so duplicating at too high a speed may cause 
frequent errors. 
14.6 Buzzer
This setting allows you to choose whether you want to hear a beep when 
you press a button or when a task has been completed.
14.7 Startup Menu
This setting allows you to choose which menu you see first when the 
duplicator is powered on.
14.8 Screen Saver
This setting allows you to enable the Screen Saver feature or not. By enabling 
this feature, a screen saver will be displayed when your duplicator has been idle 
for a long period of time.
14.9 Duplication Mode
To simplify the Hard Drive loading and copying process a feature called “Load 
and Copy”, and “On the Fly” is introduced under the category “Duplication 
Mode”.
This feature reduces the “Duplication from Hard Drive” process to a single step!
14.10 Counter
This option allows you to enable/disable the Counter feature by turning this 
feature ON or OFF. This feature will notify you how many discs have been 
copied and how many discs are left to complete your project.  
						

							www.aleratec.com63
Men\f Overview
14.11 DVD+R High Compatibility Mode
This feature allows you to enable/disable the DVD+R High Compatibility 
Mode feature by turning this feature ON or OFF. The purpose of this 
feature is to increase the compatibility of DVD+R media with a broader 
range of DVD Video players. This process will increase the amount of 
time required to duplicate your disc(s).
14.12 ISRC
This option allows you to enable/disable copying ISRC code of the 
Audio CD. ISRC is the serial# of the audio tracks that uniquely identifies 
the song in that audio track. This ISRC code is commonly found in 
commercial Audio CD and rarely seen on the home made Audio CDs. By 
enabling this feature, the duplication performance will be lowered.
14.13 Disable Drives
This feature allows you to disable certain drives/trays when those drives/
trays are producing high failure rates or not functioning properly.
14.14 USB Connection
This feature allows you to turn on/off the USB port on the back of 
your duplicator. This option will allow a Writer on the duplicator to be 
controlled by a PC. This feature will only be visible if the supported USB 
Connection were installed.
*Please note that system will be restarted when this setting is changed.
14.15 Overburn (CDs Only)
This feature allows you to burn a few MB more than the standard capacity of the 
target CD (e.g. 75 minutes of recording time vs. 74 minutes). The default setting 
is OFF.
15.	Utilities
15.1 Disc Info
This feature will identify your blank recordable Media’s format, capacity, 
manufacture ID as well as the Media’s certified writing speed. This 
function (Disc Info) can be found in the “Utility” menu. 
Note: Thi\b feature only a\bpplie\b to media in t\bhe recording tray\b.\b  
						

							www.aleratec.com64
Men\f Overview
15.	Utilities - continued 
15.2 Prescan
This feature allows you to scan and detect any bad sectors existing in the 
Master Disc. It is recommended that you perform a Prescan before starting 
the duplication task for all Master Discs. Approximately 50% of failures 
reported by the duplicator are caused by errors in the Master Disc which 
the Reader couldn’t overcome. When this kind of failure occurs, it tends to 
waste all of your blank recordable medias. 
15.3 System Info
By entering this menu, you will be able to see the many specification of 
your duplicator such as the firmware version, CPU type, RAM capacity. You 
can check the specifications by pressing UP or DOWN button.
15.4 Device Info
By entering this menu, you will be able to see the information for devices 
built inside your duplicator. That information includes but limited to 
manufacture, model number, etc.
15.5 Load Default
This function will reset all of the options back to manufacture’s default. You 
can perform this function if your duplicator is acting abnormal. You need to 
perform “Shutdown” and restart the system in order for this to take effect.
15.6 Update Firmware
This function will update the software of your duplicator. To update, 
you need to insert manufacture Certified Update CD into the Reader and 
select this function by pressing ENT button. We strongly suggest you to 
not upgrade your duplicator’s firmware unless your duplicator is getting 
unstable.
15.7 Save
This function will save all the settings you’ve modified since last time the 
system is booted.