Home > Aleratec > Hard Disk > Aleratec 15 HDD Copy Cruiser IDE SATA Hard Disk Duplicator User Guide

Aleratec 15 HDD Copy Cruiser IDE SATA Hard Disk Duplicator User Guide

Here you can view all the pages of manual Aleratec 15 HDD Copy Cruiser IDE SATA Hard Disk Duplicator User Guide. The Aleratec manuals for Hard Disk are available online for free. You can easily download all the documents as PDF.

Page 41

www.aleratec.com35
Using the 1:5 HDD Copy Cruiser IDE/SATA 
Main Menu
Setup
Setup:	Boot	Time	Delay
If HDD can not be detected during duplicate controller boot up, this function 
can adjust the timer. 
1. Use the arrow buttons (or) to select “Setup”. The following screen 
will be displayed. 
2. Press the arrow buttons () to scroll to “Boot Time Delay”. The 
following screen will be displayed. 
3. Press ENT to display the current configuration setting (0-99 sec).
4. Use the arrow buttons () to change...

Page 42

www.aleratec.com36
Using the 1:5 HDD Copy Cruiser IDE/SATA
Main Menu
Setup
Setup:	Quick	Compare
If target HDD has too many errors, the duplicate controller will ignore it and 
keep comparing other target HDDs. 
1. Use the arrow buttons (or) to select “Setup”. The following screen 
will be displayed. 
2. Press the arrow buttons () to scroll to “Quick Compare”. The 
following screen will be displayed. 
3. Press ENT to display the current configuration setting (Off or 1 Byte - 
100 MBytes).
4. Use the...

Page 43

www.aleratec.com37
Using the 1:5 HDD Copy Cruiser IDE/SATA 
Main Menu
Advanced Setup
The “Adv Setup” menu contains additional configuration options for the 1:5 HDD 
Cruiser.  
1. Press and hold the ESC	button for 3 seconds to enter Adv Setup. The following 
screen will be displayed.
Note: After changing any of the configuration options, you must 
press ENT to accept the change. Once all changes are complete, 
press ESC to exit the Adv Setup menu. The following screen will be 
displayed. 
2. When the...

Page 44

www.aleratec.com38
Using the 1:5 HDD Copy Cruiser IDE/SATA 
Main Menu
Adv Setup
Adv	Setup:	Read	Error	Skip
This function can be enabled to ignore any error that occurs during copying.  
By default, the 1:5 HDD Cruiser will halt the copy operation when it encounters 
an unreadable area of the source hard disk and display an error. Enabling this 
option will ignore any bad sectors on the source hard drive by skipping over 
them.  
Warning: Setting this function to “On” may result in corrupt data on 
copied...

Page 45

www.aleratec.com39
Using the 1:11 HDD Copy Cruiser IDE/SATA 
Main Menu
Adv Setup
Adv	Setup:	Update	Firmware
This function is used to update the 1:5 HDD Cruiser firmware to a later version. 
Note: Firmware updates are available from Aleratec technical support.    
1.a CD method 
Open the case of the 1:5 HDD Cruiser . Disconnect the SATA cable from the blue 
connector on the controller board.  Connect a SATA DVD/CD drive (not included) 
to the blue connector.  Place the firmware CD in the DVD/CD drive....

Page 46

www.aleratec.com40
Using the 1:5 HDD Copy Cruiser IDE/SATA 
Main Menu
Adv Setup
Adv	Setup:	Compare	Firmware
This function is used to compare the firmware version currently installed with 
one on a DVD/CD disc. 
Note: Use “Compare Firmware” after updating the firmware from 
e-mail or from the Aleratec web site. This function is used after 
performing a firmware update on the 1:5 HDD Cruiser. 
1. Press and hold ESC for about three seconds to access the “Adv Setup” 
menu. The following screen will be...

Page 47

www.aleratec.com41
Using the 1:5 HDD Copy Cruiser IDE/SATA 
Main Menu
Adv Setup
Adv	Setup:	Quick	Erase	HDD
This function is used to erase the data of a hard drive quickly. 
Warning: Backup any important data before using this function. 
1. Press and hold ESC for about three seconds to access the “Adv Setup” 
menu. The following screen will be displayed. 
2. Use the arrow buttons (or) to select “Quick Erase HDD”. The 
following screen will be displayed.
3. Press ENT, and then use the arrow keys () to...

Page 48

www.aleratec.com42
Using the 1:5 HDD Copy Cruiser IDE/SATA 
Main Menu
Adv Setup
Adv	Setup:	Full	Erase	HDD
This function is used to fully erase all data on the HDD. 
Warning: Backup any important data before using this function. 
1. Press and hold ESC for about three seconds to access the “Adv Setup” 
menu. The following screen will be displayed. 
2. Use the arrow buttons (or) to select “Full Erase HDD”. The following 
screen will be displayed.
3. Press ENT, and then use the arrow keys () to select a...

Page 49

www.aleratec.com43
Using the 1:5 HDD Copy Cruiser IDE/SATA 
Main Menu
Adv Setup
Adv	Setup:	H/W	Diagnostic
This function is used to test various components of the 1:5 HDD Cruiser. 
1. Press and hold ESC for about three seconds to access the “Adv Setup” 
menu. The following screen will be displayed. 
2. Use the arrow buttons (or) to select “H/W Diagnostic”. The following 
screen will be displayed. 
3. Press ENT to begin the diagnostic tests. The following tests will be 
performed: Button Test, Self-Test...

Page 50

www.aleratec.com44
Using the 1:5 HDD Copy Cruiser IDE/SATA 
Main Menu
Adv Setup
Adv	Setup:	Load	Default
This function is used to restore all factory settings of the 1:5 HDD Cruiser back 
to their original defaults. 
1. Press and hold ESC for about three seconds to access the “Adv Setup” 
menu. The following screen will be displayed. 
2. Use the arrow buttons (or) to select “Load Default”. The following 
screen will be displayed. 
3. Press ENT to proceed to the following screen:
Press ENT to confirm...
Start reading Aleratec 15 HDD Copy Cruiser IDE SATA Hard Disk Duplicator User Guide

Related Manuals for Aleratec 15 HDD Copy Cruiser IDE SATA Hard Disk Duplicator User Guide

All Aleratec manuals