Home > Aleratec > Hard Disk > Aleratec 124 HDD Copy Cruiser IDESATA HighSpeed WL User Guide

Aleratec 124 HDD Copy Cruiser IDESATA HighSpeed WL User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Aleratec 124 HDD Copy Cruiser IDESATA HighSpeed WL User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							www.aleratec.com15
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    Main Menu
    Copy
    The “Copy” function performs a copy from a source HDD to one or more target HDDs. 
    The target HDDs must be at least as large as the source. The HDD Copy Cruiser IDE/
    SATA High-Speed WL will copy every block of capacity on the source HDD. 
    1. Load the source HDD and the target HDDs into the HDD Copy Cruiser IDE/
    SATA High-Speed WL. The system will auto-detect the hard drives. After the 
    drives have been detected, a screen similar to the one below will be displayed. 
    Note: Before copying be sure that the capacity of the target HDD is equal to or larger than the source hard drive. 
    2. Press OK to start copying. The system will auto-detect the hard drives. The 
    following information will be displayed. 
    
    ESC
    OK2014/10/07                          09:50 
    1. Copy 
    
    ESC
    OKCopy
    Searching Source
    
    ESC
    OKCopy 
    Analyzing Source
    
    ESC
    OKCopy              50.9G
              1 Ready
    
    ESC
    OKCopy 
    Partition #1              25%  
    						
    							www.aleratec.com16
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    Main Menu
    Copy - Continued
    3. During the copy process the HDD Copy Cruiser IDE/SATA High-Speed WL 
    will display progress information.
     
    The amount of data remaining to be transferred (shown in gigabytes), and time 
    will be displayed as the percentage of completion increases. 
    Note: The copying speed, capacity and duration may vary from one hard drive to another. 
    4. Once duplication is complete, a job status screen will be displayed.
    
    ESC
    OKPass: 1  Fail: 0
    Time: 20:18
    
    ESC
    OKCopy x 11  50.9 G
    7:35    26% 13.5 G  
    						
    							www.aleratec.com17
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    Main Menu
    Compare
    The “Compare” function performs a comparison of data from the source hard drive 
    to the data on the target hard drives. 
    1. With the source and target HDDs loaded use the arrow buttons (or) to 
    select “Compare”. The following screen will be displayed. 
    2. Press OK to begin the comparison. The system will auto-detect the hard drives.  
     
     
     
     
    During the compare process, the HDD Copy Cruiser IDE/SATA High-Speed 
    WL will display progress information. Press OK to continue.
    
    ESC
    OK2014/10/07                          09:50
    2. Compare
    
    ESC
    OKCompare 
    Searching Source
    
    ESC
    OKCompare x 11 50.9 G
    0:23             1%  937 M
    
    ESC
    OKAnalyzing Source
    Partition #1              20%
    
    ESC
    OKCompare              50.9G
              11 Ready  
    						
    							www.aleratec.com18
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    Main Menu
    Compare - Continued
    3. When the comparison is completed, a job status screen will be displayed.
    
    ESC
    OKPass: 11  Fail: 0
    Time: 20:18  
    						
    							www.aleratec.com19
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    Main Menu
    Copy+Compare
    The “Copy+Compare” function performs a copy and compare from a source HDD to 
    one or more target HDDs. The target HDDs must be at least as large as the source. The 
    HDD Copy Cruiser IDE/SATA High-Speed WL will copy every block of capacity on 
    the source HDD. 
    1. Load the source HDD and the target HDDs into the HDD Copy Cruiser IDE/
    SATA High-Speed WL. The system will auto-detect the hard drives. After the 
    drives have been detected, a screen similar to the one below will be displayed. 
    Note: Before copying be sure that the capacity of the target HDD is equal to or larger than the source hard drive. 
    2. Press OK to start copying. The system will auto-detect the hard drives. The 
    following information will be displayed. 
    
    ESC
    OK2014/10/07                          09:50 
    3. Copy+Compare 
    
    ESC
    OKCopy
    Searching Source
    
    ESC
    OKAnalyzing Source  
    Partition #1              10%
    
    ESC
    OKCopy              50.9G
              11 Ready  
    						
    							www.aleratec.com20
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    Main Menu
    Copy+Compare - Continued
    3. During the copy process the HDD Copy Cruiser IDE/SATA High-Speed WL 
    will display progress information.
     
     
     
     
     
     
     
    The amount of data remaining to be transferred (shown in gigabytes), and time 
    will be displayed as the percentage of completion increases. 
    Note: The copying speed, capacity and duration may vary from one source hard drive to another. 
    4. Once duplication is complete, a job status screen will be displayed.
    
    ESC
    OKPass: 11  Fail: 0
    Time: 20:18
    
    ESC
    OKCopy x 11  50.9 G
    7:35      26% 13.5 G
    
    ESC
    OKCompare x 11 50.9 G
    0:23             1%  937 M  
    						
    							www.aleratec.com21
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    Main Menu
    Overwrite
    The “Overwrite” function will sanitize (wipe clean of all data) the hard disk drives 
    connected to the HDD Copy Cruiser IDE/SATA High-Speed WL. 
    1. Load up to 11 HDDs into the HDD Copy Cruiser IDE/SATA High-Speed WL. 
    The system will auto-detect the hard drives. Using the arrow buttons (or) 
    select “Overwrite”. The following screen will be displayed. 
    Note: Overwriting the entire capacity of all connected hard drives can take an extended period of time.   
    2. Press OK to select. The following information will be displayed.
    3. Use the arrow buttons to scroll between the types of overwrite: Quick 
    Overwrite, Full Overwrite, 3 Pass, 3 Pass with Verify,  
    7-Pass Overwrite, or Security Erase.   
     A.			Quick	Overwrite
    A1. To perform a Quick Overwrite, select “Quick Overwrite” and press OK. 
     
    A2.  The loading pattern process for the Quick Overwrite will be displayed.  
    
    ESC
    OK2014/10/07                          09:50
    4. Overwrite
    
    ESC
    OK[ 4. Overwrite ]
    1. Quick Overwrite
    
    ESC
    OK[ 4. Overwrite ]
    1. Quick Overwrite
    
    ESC
    OKQuick Overwrite 
    Loading Pattern  
    						
    							www.aleratec.com22
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    Main Menu
    Overwrite
     A.			Quick	Overwrite	-	Continued
    A3. The estimated time elapsed for the Quick Overwrite process will be displayed. 
            A4.  When the process is finished, the following screen will be shown. 
     
     
     
     
    B.			Full	Overwrite
    B1. To perform a Full Overwrite, scroll to “Full Overwrite” and press OK. The 
    following screen will be displayed. 
    B2. The loading pattern process for the Full Overwrite will be displayed. 
    B3. The estimated time elapsed for the Full Overwrite process will be displayed.       
     
    ESC
    OKQuick Overwrite 
        13:30
    
    ESC
    OK[ 4. Overwrite ]
    2. Full Overwrite 
    
    ESC
    OKFull Overwrite 
    Loading Pattern
    
    ESC
    OKQuick Overwrite 
    Pass: 11          Fail: 0
    
    ESC
    OKFull Overwrite 
                           13:30   
    						
    							www.aleratec.com23
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    B.			Full	Overwrite	-	Continued
     
           B4. When the process is finished, the following screen will be shown.
     
     
     
     
     
     
    Main Menu
    Overwrite 
    C.			3-Pass
    C1. To perform a 3-Pass Overwrite, scroll to “3-Pass” and press OK. The 
    following screen will be displayed. 
    C2. The loading pattern process for the 3-Pass Overwrite will be displayed. 
    C3. The estimated time elapsed for the 3-Pass Overwrite process will be displayed. 
     
    C4. When the process is finished, the following screen will be shown. 
    
    ESC
    OK[ 4. Overwrite ]
    3. 3-Pass Overwrite 
    
    ESC
    OK3-Pass Overwrite 
    Loading Pattern
    
    ESC
    OK3-Pass Overwrite 
                           13:30 
    
    ESC
    OKFull Overwrite 
    Pass: 11          Fail: 0
    
    ESC
    OK3-Pass Overwrite 
    Pass: 11         Fail: 0  
    						
    							www.aleratec.com24
    Using the HDD Copy Cruiser IDE/SATA High-Speed WL 
    Main Menu
    Overwrite 
    D.			3-Pass	+	Verify
    D1. To perform a 3-Pass Overwrite + Verify, scroll to “3-Pass Overwrite + 
    Verify” and press OK. The following screen will be displayed. 
    D2. The loading pattern process for the 3-Pass Overwrite + Verify will be 
    displayed. 
    D3. The estimated time elapsed for the 3-Pass Overwrite + Verify process will be 
    displayed. 
       
    D4. When the process is finished, the following screen will be shown. 
    
    ESC
    OK[ 4. Overwrite ]
    4. 3-Pass Overwrite + Verify
    
    ESC
    OK3-Pass Overwrite + Verify 
    Loading Pattern
    
    ESC
    OK3-Pass Overwrite + Verify
                           13:30 
    
    ESC
    OK3-Pass Overwrite + Verify 
    Pass: 11          Fail: 0  
    						
    All Aleratec manuals Comments (0)

    Related Manuals for Aleratec 124 HDD Copy Cruiser IDESATA HighSpeed WL User Guide