Aleratec 124 HDD Copy Cruiser HighSpeed Duplicator User Guide
Have a look at the manual Aleratec 124 HDD Copy Cruiser HighSpeed Duplicator User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
www.aleratec.com15 Using the HDD Copy Cruiser High-Speed Main Menu Copy - Continued 3. During the copy process the HDD Copy Cruiser High-Speed will display progress information. The amount of data remaining to be transferred (shown in gigabytes), and time will be displayed as the percentage of completion increases. Note: The copying speed, capacity and duration may vary from one hard drive to another. 4. Once duplication is complete, a job status screen will be displayed. ESC OKPass: 1 Fail: 0Time: 20:18 ESC OKCopy 11 50.9 G7:35 26% 13.5 G
www.aleratec.com16 Using the HDD Copy Cruiser High-Speed Main Menu Compare The “Compare” function performs a comparison of data from the source hard drive to the data on the target hard drives. 1. With the source and target HDDs loaded use the arrow buttons (or) to select “Compare”. The following screen will be displayed. 2. Press OK to begin the comparison. The system will auto-detect the hard drives. During the compare process, the HDD Copy Cruiser High-Speed will display progress information. Press OK to continue. ESC OKAleratec 2. Compare ESC OKSearching Source ESC OKCompare 11 50.9 G0:23 1% 937 M ESC OKAnalyzing Source ESC OKCompare 50.9 G11 Target Ready
www.aleratec.com17 Using the HDD Copy Cruiser High-Speed Main Menu Compare - Continued 3. When the comparison is completed, a job status screen will be displayed. ESC OKPass: 11 Fail: 0Time: 20:18
www.aleratec.com18 Using the HDD Copy Cruiser High-Speed Main Menu Copy+Compare The “Copy+Compare” function performs a copy and compare from a source HDD to one or more target HDDs. The target HDDs must be at least as large as the source. The HDD Copy Cruiser High-Speed will copy every block of capacity on the source HDD. 1. Load the source HDD and the target HDDs into the Copy Cruiser High- Speed. The system will auto-detect the hard drives. After the drives have been detected, a screen similar to the one below will be displayed. Note: Before copying be sure that the capacity of the target HDD is equal to or larger than the source hard drive. 2. Press OK to start copying. The system will auto-detect the hard drives. The following information will be displayed. ESC OKAleratec 3. Copy+Compare ESC OKSearching Source ESC OKAnalyzing Source ESC OKCopy 50.9 G11 Target Ready
www.aleratec.com19 Using the HDD Copy Cruiser High-Speed Main Menu Copy+Compare - Continued 3. During the copy process the HDD Copy Cruiser High-Speed will display progress information. The amount of data remaining to be transferred (shown in gigabytes), and time will be displayed as the percentage of completion increases. Note: The copying speed, capacity and duration may vary from one source hard drive to another. 4. Once duplication is complete, a job status screen will be displayed. ESC OKPass: 11 Fail: 0Time: 20:18 ESC OKCopy 11 50.9 G7:35 26% 13.5 G ESC OKCompare 11 50.9 G0:23 1% 937 M
www.aleratec.com20 Using the HDD Copy Cruiser High-Speed Main Menu Overwrite The “Overwrite” function will sanitize (wipe clean of all data) the hard disk drives connected to the HDD Copy Cruiser High-Speed. 1. Load up to 25 HDDs into the HDD Copy Cruiser High-Speed. The system will auto-detect the hard drives. Using the arrow buttons (or) select “Overwrite”. The following screen will be displayed. Note: Overwriting the entire capacity of all connected hard drives can take an extended period of time. 2. Press OK to select. The following information will be displayed. 3. Use the arrow buttons to scroll between the types of overwrite: Quick Overwrite, Full Overwrite, 3 Pass, 3 Pass with Verify, 7-Pass Overwrite, or Security Erase. A. Quick Overwrite A1. To perform a Quick Overwrite, select “Quick Overwrite” and press OK. A2. The estimated time elapsed for the Quick Overwrite process will be displayed. ESC OKAleratec 4. Overwrite ESC OK4. Overwrite1. Quick Overwrite ESC OK[ 4. Overwrite ]4.1 Quick Overwrite ESC OKIn ProcessElapsed 13:30
www.aleratec.com21 Using the HDD Copy Cruiser High-Speed Main Menu Overwrite A. Quick Overwrite - Continued A3. When the process is finished, the following screen will be shown. B. Full Overwrite B1. To perform a Full Overwrite, scroll to “Full Overwrite” and press OK. The following screen will be displayed. B2. The estimated time elapsed for the Full Overwrite process will be displayed. B3. When the process is finished, the following screen will be shown. ESC OKQuick Overwrite Pass: 11 Fail: 0 ESC OK[ 4. Overwrite ]4.2 Full Overwrite ESC OKIn ProcessElapsed 13:30 ESC OKFull Overwrite Pass: 11 Fail: 0
www.aleratec.com22 Using the HDD Copy Cruiser High-Speed Main Menu Overwrite C. 3-Pass C1. To perform a 3-Pass Overwrite, scroll to “3-Pass” and press OK. The following screen will be displayed. C2. The estimated time elapsed for the 3-Pass process will be displayed. C3. When the process is finished, the following screen will be shown. ESC OK[ 4. Overwrite ]4.3 3-Pass ESC OKIn ProcessElapsed 13:30 ESC OK3-Pass Pass: 11 Fail: 0
www.aleratec.com23 Using the HDD Copy Cruiser High-Speed Main Menu Overwrite D. 3-Pass + Verify D1. To perform a 3-Pass + Verify Overwrite, scroll to “3-Pass + Verify” and press OK. The following screen will be displayed. D2. The estimated time elapsed for the 3-Pass + Verify process will be displayed. D3. When the process is finished, the following screen will be shown. ESC OK[ 4. Overwrite ]4.4 3-Pass + Verify ESC OKIn ProcessElapsed 13:30 ESC OK3-Pass + Verify Pass: 11 Fail: 0
www.aleratec.com24 Using the HDD Copy Cruiser High-Speed Main Menu Overwrite E. 7-Pass Overwrite This method will write over the entire capacity of the hard drives connected to the HDD Copy Cruiser High-Speed seven different times. DoD 5220.22M is the Department of Defense document that discusses both Three and Seven Pass Overwrite data wiping. E1. To perform a Seven Pass Overwrite, scroll to “7-Pass Overwrite” and press OK. The following screen will be displayed. E2. The estimated time elapsed for the 7-Pass process will be displayed. E3. When the process is finished, the following screen will be shown. ESC OK[ 4. Overwrite ]4.5 7-Pass Overwrite ESC OKIn ProcessElapsed 13:30 ESC OK7-Pass Overwrite Pass: 11 Fail: 0