Aleratec 124 HDD Copy Cruiser HighSpeed Duplicator User Guide
Have a look at the manual Aleratec 124 HDD Copy Cruiser HighSpeed Duplicator User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
www.aleratec.com5 Introduction Key Items 1:24 HDD Copy Cruiser High-Speed - Part Number: 350128 Display Panel(see page 6)ControllerDrive Bay Locks Target Drive Bays Target Drive Bays Source Drive Bay Power Switch Drive ActivityLightsDrive Bay Handle/TabPower LED
www.aleratec.com6 Introduction HDD Copy Cruiser High-Speed Copy Controller Display Panel and Buttons (Actual display may vary from illustration) 1. LCD display shows all functions and messages 2. OK button is used to execute a selected function, or enter a menu 3. ESC button is used to cancel a selected function, or exit a menu 4. UP arrow is used to scroll backward through functions or menus 5. DOWN arrow is used to scroll forward through functions or menus HDD Cruiser 1-11 ver: 2.32.0 1 3 2 ESC OK 5 4 Duplicator Stand Installation Instructions (350126 only)
www.aleratec.com7 Precautions Before installing your HDD Copy Cruiser High-Speed, please read the following. Installation Avoid placing the HDD Copy Cruiser High-Speed in a location subject to: • High humidity • High temperature • Excessive dust • Mechanical vibration • Direct sunlight • Electromagnetic radiation Power This product has two auto switching PSUs. Choose a Good Location 1. Allow adequate clearance for moving parts. 2. Do not place near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. 3. Disconnect the AC power cord from the outlet if the product is not used for an extended period of time. 4. Proper care will help assure maximum product life. Improper operating environment and misuse may void the warranty. Operation Do not move the HDD Copy Cruiser High-Speed during operation. This may cause a malfunction or other undesirable results. Avoid exposing the unit to sudden changes in temperature as condensation may form inside the HDD Copy Cruiser High-Speed. Should the surrounding temperature suddenly rise while the HDD Copy Cruiser High-Speed is on, wait at least one hour before turning off the power. Operating the duplicator immediately after a sudden increase in temperature may result in a malfunction. Transportation Keep the original packing materials for future moving or shipping of the HDD Copy Cruiser High-Speed. Replacement packaging may incur charge.
www.aleratec.com8 Overview Power Up Sequence During the normal power-up sequence of the HDD Copy Cruiser High-Speed, the following information will be displayed. • Figure 1 shows the searching of the station head. • Figure 2 shows the first function. ESC OKAleratec Searching Station ESC OK1. Copy
www.aleratec.com9 Overview Main Menu There are eleven main menu items that can be seen in the HDD Copy Cruiser High- Speed Controller Display Panel. These are: ESC OKAleratec 1. Copy ESC OKAleratec 2. Compare ESC OKAleratec 3. Copy+Compare ESC OKAleratec 4. Overwrite ESC OKAleratec 5. Utility ESC OKAleratec 6. Setup 1. 2. 3. 4. 5. 6.
www.aleratec.com10 Overview Subfunctions The “Overwrite” menu has six subfunctions. These are: The “Utility” menu has three subfunctions. These are: 4.1 Quick Overwrite 4.2 Full Overwrite 4.3 3-Pass 4.4 3-Pass + Verify 4.5 . 7-Pass Overwrite 4.6 Secure Erase 5.1 Show HDD Info 5.2 Update System 5.3 System Info ESC OKAleratec 4. Overwrite ESC OKAleratec 5. Utility
www.aleratec.com11 Overview Subfunctions The “Setup” menu has nine subfunctions. These are: 6.1 Copy Area 6.2 Skip Error 6.3 Erase Master 6.1.1 System and Files 6.1.2 ALL Partitions 6.4 Unknown Format 6.5 Transfer Rate 6.6 Buzzer 6.7 Language 6.8 Advanced Setup 6.9 Restore Default 6.1.3 Whole HDD 6.3.1 Disable 6.3.2 Enable 6.4.1 Copy Unknown 6.4.2 Skip Unknown 6.8.1 Wait HDD Time 6.8.2 Copy HPA area 6.6.1 Turn On 6.6.2 Mute ESC OKAleratec 6. Setup 6.7.1 English 6.7.2 Chinese
www.aleratec.com12 Using the HDD Copy Cruiser High-Speed Loading the Hard Drives 1. Open the drive tray doors by pulling the tab on the left side of each drive bay you wish to use. 2. Take the Hard Disc Drive (HDD) and align the drive’s SATA plug to the lower right hand side of the drive bay. 3. Slide the HDD into the drive bay until it stops. The drive will still be about 1 inch outside of the bay. When the door is closed it will push and plug the HDD into the duplicator. 4. Swing the drive bay door closed and press the left side of the door until the tab latches. When it latches, a click can be felt and heard. Note: If you are duplicating, the source hard disk drive goes in the top bay. Source Drive Bay
www.aleratec.com13 Using the HDD Copy Cruiser High-Speed Removing Hard Drives 1. Open the drive tray doors by pulling the handle/tab on the left side of each drive tray door. Note: Do not attempt to remove the hard drive if the drive activity LED is on. If drive tray door is locked, use the included key to open. 2. To disengage the HDD, swing the drive tray door to the full open position. 3. Pull drive forward and remove drive.
www.aleratec.com14 Using the HDD Copy Cruiser High-Speed Main Menu Copy The “Copy” function performs a copy from a source HDD to one or more target HDDs. The target HDDs must be at least as large as the source. The HDD Copy Cruiser High-Speed will copy every block of capacity on the source HDD. 1. Load the source HDD and the target HDDs into the HDD Copy Cruiser High- Speed. The system will auto-detect the hard drives. After the drives have been detected, a screen similar to the one below will be displayed. Note: Before copying be sure that the capacity of the target HDD is equal to or larger than the source hard drive. 2. Press OK to start copying. The system will auto-detect the hard drives. The following information will be displayed. ESC OKAleratec 1. Copy ESC OKSearching Source ESC OKAnalyzing Source ESC OKCopy 50.9 G1 Target Ready