Aleratec 115 DVDCD Tower Publisher SLS User Guide

							www.aleratec.com25
Stand-Alone Tower Publisher LS: Tutorials
How to Make Copies from the Hard Drive - continued
b. Press ENT to enter Hard Drive Setup Menu and you shall see the following:
c. Now, load your Master Disc on to the Hard Drive. To do so, use UP or 
DOWN arrow button to navigate to the following screen.
d. Press ENT to enter Load Partition Menu and you shall see the following:
e. Now, you have a choice to load your Master Disc into a new (empty) 
partition or overwrite one of the existing partitions (if any exists, including 
Reserved Partition) by inputting and modifying the name you desire; or 
you can simply choose “Auto Generate” to have the system automatically 
generate a partition name for you. Afterwards, simply press the UP or 
DOWN arrow button to find your desired selection and press ENT to submit 
your selection. You will see the following (unless you have chosen “Auto 
Generate”, then please skip to Step “h”):
f. Now, you can name the partition you are about to load into the Hard Drive. 
To enter the name, you need to use the UP or DOWN buttons to select the 
character and use ENT or ESC button to move the cursor position and once 
you’ve finished, move the cursor to OK and press ENT.  
*The 228GB indicates the available capacity of your hard drive in terms of GB.
COPYTESTPRINTSOURCE
ESCENT


Hard Drive Setup1. Select Partition
COPYTESTPRINTSOURCE
ESCENT


Hard Drive Setup2. Load Partition
COPYTESTPRINTSOURCE
ESCENT


Load Partition [ 228GB]Load -> New Partition
COPYTESTPRINTSOURCE
ESCENT


Edit Partition Name[          ] OK?                   
						

							www.aleratec.com26
Stand-Alone Tower Publisher LS: Tutorials
For example, if you want to name the partition for your Master Disc as 
“FUN”. Then do the following:
Make sure the cursor is located at the first position:
i. Press DOWN button consecutively until “F” is displayed.
ii. Press ENT button once to move the cursor to the next position.
iii. Press DOWN button consecutively until “U” is displayed.
iv. Press ENT button once to move the cursor to the next position.
v. Press DOWN button consecutively until “N” is displayed.
vi. Press ENT button once to move the cursor to the next position.
vii. Now, we have the name “FUN” displayed and then, press ENT 
consecutively until the cursor is moved to OK.
viii. Then, press ENT once to submit your name selection.
g. Now you shall see the following confirmation screen:
h. Press ENT button to confirm. Once your Master Disc has been recognized. The 
loading progress indicator will be displayed and you shall see the following:
“4000MB” indicates the total capacity of your Master Disc.
“423MB” indicates the current MB from the Master Disc that has been loaded.
“FUN” indicates the name of the partition the data is being loaded onto.
“10%” indicates the current percentage of the Master Disc that has been loaded.
COPYTESTPRINTSOURCE
ESCENT


Edit Partition Name[X       ] OK?
COPYTESTPRINTSOURCE
ESCENT


Load Partition?[FUN        ] OK?
COPYTESTPRINTSOURCE
ESCENT


Loading... 4000MBFUN 10%  423MB                  
						

							www.aleratec.com27
Stand-Alone Tower Publisher LS: Tutorials
How to Make Copies from the Hard Drive - continued
i. Once your Master Disc has been loaded completely, you shall see the 
following:
Then, you can press ENT button to go back to the Hard Drive Setup Menu.
3. Go back to “COPY” Menu.
a. Press ENT button to go back to the main menu. You shall see the following:
b. Use UP or DOWN arrow button to navigate to the following screen.
4. Start the Copy Process.
a. Now, please insert your blank discs into the Writer Trays (make sure the 
Reader Tray is empty) and press ENT button to enter the “COPY” menu. 
You will be asked to choose which hard drive partition to copy from:
b. Choose the desired partition to copy from and press ENT button to submit 
your selection. Then you shall see the following Counter Selection Menu:
c. The Counter Selection Menu will let you to choose how many copies you 
want to make for your project. This Counter Selection feature will allow 
the duplicator to count the number of copies you’ve made and prompt you 
when the desired number of copies has been made.
COPYTESTPRINTSOURCE
ESCENT


Load Partition OK!Press OK to Continue 
COPYTESTPRINTSOURCE
ESCENT


DUPLICATOR 1.0011. Hard Drive Setup
COPYTESTPRINTSOURCE
ESCENT


DUPLICATOR 1.001.0 COPY
COPYTESTPRINTSOURCE
ESCENT


Choose Partition:[FUN      ] DVD 4000MB
COPYTESTPRINTSOURCE
ESCENT


Counter:No Counter                      
						

							www.aleratec.com28
Stand-Alone Tower Publisher LS: Tutorials
You can select “No Counter” if you prefer to copy continuously with no 
interruption. (It will still count the number of copies, but it will not notify 
you when to stop.) To select the “No Counter”, simply press ENT button 
when you see the screen above. Then skip below and continue on to step 
“d”.
Or, you can select “Specify Counter” to specify the number of copies (1 to 
9999) by pressing the UP or DOWN navigation button to the below screen:
Then please press ENT button to submit. You shall see the screen below:
To specify the number of copies for your project, you need to enter/input 
a 4-digit number. If you are planning to specify a number that is less than 
4 digits, please fill the leading spaces with “0”s (any leading “0” will 
be skipped). An example of that 4-digit number could be “0234” (Two 
hundred and thirty four), or “0010” (ten). Remember, the beginning “0”s 
are skipped, therefore “0010” means “10”, which is the number 10.
To enter the number, you need to use UP or DOWN button to select the 
number for each digit and use ENT or ESC button to move the cursor 
position right or left, once you’ve finished, move the cursor to OK and 
press ENT. For example, if I want to specify a counter value of 21 (twenty 
one). The 4-digit value would be “0021”. To input the desired quantity, 
please do the following:
Make sure the cursor is located at the first position:
i. Press DOWN button consecutively until “0” is displayed.
ii. Press ENT button once to move the cursor to the next position.
iii. Press DOWN button consecutively until “0” is displayed.
iv. Press ENT button once to move the cursor to the next position.
v. Press DOWN button consecutively until “2” is displayed.
vi. Press ENT button once to move the cursor to the next position.
COPYTESTPRINTSOURCE
ESCENT


Counter:Specify Counter
COPYTESTPRINTSOURCE
ESCENT


Specify Counter:[0        ] OK?
COPYTESTPRINTSOURCE
ESCENT


Specify Counter:[X        ] OK?              
						

							www.aleratec.com29
Stand-Alone Tower Publisher LS: Tutorials
How to Make Copies from the Hard Drive - continued
vii. Press DOWN button consecutively until “1” is displayed.
viii. Now, we have “0021” displayed and then, press ENT once and the 
cursor is now moved to OK.
ix. Then, press ENT once to submit your counter value.
Now you shall see following screen:
Note: If the ABOVE screen is displayed for more than 2 minutes, 
please check your Blank Discs for quality.
d. Please allow 5-10 seconds for the duplicator to detect your Hard Drive 
partition and Blank Discs as well. After your Hard Drive partition and 
Blank Discs have been recognized, then you shall see the following 
screen:
Note: By default, the “Auto Start” setting is set to “Auto”. For 
example, if your duplicator has detected 3 blank discs and 
didn’t detect any additional blank discs for 30 seconds, then the 
duplication will be started automatically.
Note: Once the number of blank discs you inserted matches 
the number of discs detected on the screen. Then press ENT (if 
you are not using Auto Start or wish to speed up the process) to 
confirm and the following Processing screen will appear.
The “7” indicates there are 7 discs that were recognized by the recording tray. Actual quantity may be differentdepending on your machine.
COPYTESTPRINTSOURCE
ESCENT


Preparing...Waiting for Blanks
COPYTESTPRINTSOURCE
ESCENT


Preparing...7 Disc Detected, Go?
COPYTESTPRINTSOURCE
ESCENT


Processing... Please Wait               
						

							www.aleratec.com30
Stand-Alone Tower Publisher LS: Tutorials
Note: If the number of blank discs you inserted doesn’t match 
the number of discs detected on the screen, please give 10-15 
seconds for the duplicator to recognize all of your blank discs.
e. After 2 or 3 seconds of processing time, the following Copy Progress 
Screen will appear.
Note: It is normal to see the progress indicator stays at 0-10% 
and 100% for approximately 30 seconds for CD duplication 
and up to 1 minute for DVD duplication. That is caused by the 
initializing and finalizing stages.
Once the duplication run is completed, the good copies will be ejected and 
you shall see the following screen:
“PASS 7” indicates that you’ve just made 7 successful copies.
“FAIL 0” indicates that you have no failure in this run.
“7” indicates that you’ve successfully copied 7 copies so far.
Counter SpecifiedNo Counter
“4012MB” indicates the capacity of the Master Disc.
“481MB” indicates the current MB from the Master Disc that has been copied.
“12%” indicates the current progress of the duplication.
“0/21” indicates you have a project size of 21 copies and you have made 0 copies so far.
“H” indicates you are copying from a Hard Drive Image.
“4012MB” indicates the capacity of the Master Disc.
“481MB” indicates the current MB from the Master Disc that has been copied.
“12%” indicates the current progress of the duplication.
“0” indicates that you have made 0 copies so far.
“H” indicates you are copying from a Hard Drive Image.
COPYTESTPRINTSOURCE
ESCENT


Copying...  H4012MB0/21  12%    481MB
COPYTESTPRINTSOURCE
ESCENT


Copying...   H4012MB       0  12%    481MB
COPYTESTPRINTSOURCE
ESCENT


PASS  7  FAIL  0  (   7)Waiting for Blanks                           
						

							www.aleratec.com31
Stand-Alone Tower Publisher LS: Tutorials
How to Make Copies from the Hard Drive - continued
Next, refill more blank media to continue making more copies, or you can press 
ESC to terminate your project and go back to the main menu.
If you’ve specified a counter value for your project and your project is 
completed, you shall see the following screen:
If you see above message, you can press ENT to go back to main menu.
Note: If you enabled the counter and the number of discs you have 
inserted is more than what you requested, you will receive a message 
regarding you have inserted more discs than what you need. You can 
continue to copy or you can eject the extras.
Note: Failed discs will not be ejected automatically. You will need to 
manually eject these. Throw away any failed CD-R (write once) discs.
COPYTESTPRINTSOURCE
ESCENT


21 Disc CopiedPress OK to Finish      
						

							www.aleratec.com32
Stand-Alone Tower Publisher LS: Tutorials
Select Burn Speed
This process will allow you to adjust the duplication speed subject to your various 
needs.
By default, the duplication speed will be set to the optimal speed. However, 
under some circumstances, you might want to lower the duplication speed.  Those 
circumstances are as follows:
• Poor Blank Media Quality – When your media quality is not good, lowering 
down the duplication speed is necessary to make good copies.
• Poor Master Disc Quality – If your Master Disc condition is not good, lowering 
down the duplication speed will reduce the failure rates greatly.
• Duplication Quality – Overall, the lower the speed, the higher the quality of 
your duplicates. If you have time, it is a good choice to lower down the speed to 
produce the best quality duplicates.
Turn on your duplicator. After it has finished booting up, you will see the following 
display.
1. Navigate to the “Speed Selection” menu.
Press UP or DOWN arrow button to navigate to the following screen.
2. Enter the “Speed Selection” menu.
Press ENT button to enter into “Speed Selection” menu. You will see the 
following display:
COPYTESTPRINTSOURCE
ESCENT


DUPLICATOR 1.001. COPY
COPYTESTPRINTSOURCE
ESCENT


DUPLICATOR 1.008. Select Burn Speed
COPYTESTPRINTSOURCE
ESCENT


Select Burn Speed:DVD to DVD              
						

							www.aleratec.com33
Stand-Alone Tower Publisher LS: Tutorials
Select Burn Speed - continued 
3. Select duplication speed type.
There are different types of recording speeds:
 ▪HDD/CD to CD: Copying to CD-R/RW Media from Pre-loaded CD 
Partition or Original CD Media.
 ▪HDD/DVD to DVD: Copying to DVD±R Media from Pre loaded DVD 
Partition or Original DVD Media.
 ▪HDD/DVD-DL to DVD-DL: Copying to Double/Dual Layer Recordable 
DVD Media from Pre-loaded DVD-DL Partition or Original Double/Dual 
Layer DVD Media.
To select the recording speed types, you need to press UP or DOWN button to 
adjust and press ENT button to submit your selection.
4. Select desired duplication speed.
Once you have submitted the duplication speed type, you will see the following 
display:
Press UP or DOWN button to select the desired speed and then press ENT to 
submit your speed selection.
5. Once your selection has been changed successfully, you shall see the following 
screen for 2 seconds.
Then you will be directed back to the main menu:
COPYTESTPRINTSOURCE
ESCENT


DVD to DVD Speed:6x
COPYTESTPRINTSOURCE
ESCENT


DVD to DVD Speed:Adjusted to 4x
COPYTESTPRINTSOURCE
ESCENT


DUPLICATOR 1.008. Select Burn Speed              
						

							www.aleratec.com34
Stand-Alone Tower Publisher LS: Tutorials
Select the Source Drive
When making a copy, you will need to specify where the master is. Is it in the ROM 
drive? Or is it an Image inside the Hard Drive? This tutorial will show you how to 
change the Master Reading Source to satisfy your needs.
Basically, there are 3 scenarios that require you to select the Source drive.
1. Disc-to-Disc copy (Copy from 1st Tray) – This is the case when you would 
normally make copies on the fly. You need to set the “ROM drive” as your 
Master Reading Source.
2. Hard Drive-to-Disc copy – If you want to make copies from your Hard Drive 
Image, you need to select the source as “Hard Drive”.
There are three benefits to copy from Hard Drive:
a. Performance – Duplicating form the Hard Drive will be able to boost the 
DVD duplication speed to 8x or above.
b. Stability – Duplicating from Hard Drive will stabilize the duplication 
process compared to the Disc to Disc duplicating.
c. Convenience – With your Master Discs stored inside the Hard Drive, you 
can have access to each one easily. There is no need to carry your Master 
Discs; they are all stored inside the duplicator.
3. Disc-to-Disc copy (Copy from 2nd Tray) – This is the case when your Master 
Disc is full of scratches. You would need to use the Writer Tray as your Source 
to make a copy and use the new copy as your new master to make more copies.
When you turn on your duplicator, after it has booted up, you should see the 
following signifying your duplicator is ready.
a. Navigate to Source Selection Menu.
Press UP or DOWN arrow button to navigate to the following screen.
COPYTESTPRINTSOURCE
ESCENT


DUPLICATOR 1.001. COPY
COPYTESTPRINTSOURCE
ESCENT


DUPLICATOR 1.009. Select Source