Home > Aleratec > Hard Disk > Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide

Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide

Here you can view all the pages of manual Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide. The Aleratec manuals for Hard Disk are available online for free. You can easily download all the documents as PDF.

Page 11

www.aleratec.com5
Precautions
Before installing your HDD Copy Cruiser High-Speed WL, please read the 
following.
Installation
Avoid placing the HDD Copy Cruiser High-Speed WL in a location subject to:
• High humidity
• High temperature
• Excessive dust
• Mechanical vibration
• Direct sunlight
• Electromagnetic radiation
Power
This product has two auto switching PSUs.
Choose a Good Location
1. Allow adequate clearance for moving parts.
2. Do not place near heat sources such as radiators or air ducts, or...

Page 12

www.aleratec.com6
Overview
Power Up Sequence
During the normal power-up sequence of the HDD Copy Cruiser High-Speed WL, 
the following information will be displayed.
• Figure 1 shows the searching of the station head.
• Figure 2 shows the first function.

ESC
OKAleratec

ESC
OK2014/10/07             09:50
1. Copy  

Page 13

www.aleratec.com7
Overview
Main Menu
There are eleven main menu items that can be seen in the HDD Copy Cruiser High-
Speed WL Controller Display Panel. These are:
   

ESC
OK2014/10/07             09:50 
1. Copy

ESC
OK2014/10/07             09:50 
2. Compare

ESC
OK2014/10/07             09:50 
3. Copy+Compare

ESC
OK2014/10/07             09:50 
4. Overwrite

ESC
OK2014/10/07             09:50 
5. Utility

ESC
OK2014/10/07             09:50 
6. Setup
1.
2.
3.
4.
5.
6.

ESC
OK2014/10/07...

Page 14

www.aleratec.com8
Overview
Subfunctions
The “Overwrite” menu has six subfunctions. These are:
The “Utility” menu has three subfunctions. These are:
1.  Quick Overwrite
2.  Full Overwrite
3.  3-Pass Overwrite
4.  3-Pass Overwrite           + Verify
5.  7-Pass Overwrite
6.  Secure Erase
1.  Show Disk Info
2.  Update System
3.  System Info.

ESC
OK2014/10/07     09:50 4. Overwrite

ESC
OK2014/10/07     09:50 5. Utility  

Page 15

www.aleratec.com9
Overview
Subfunctions
The “Setup” menu has nine subfunctions. These are:
1.  Copy Area
2.  Skip Error
3.  Erase Master
1.1  System and Files
1.3  Whole HDD
4.  Unknown Format
5.  Transfer Rate
6.  Buzzer
7.  Language
9.  Advanced Setup
10.  Restore Default
1.4  Percentage
3.1  Disable
3.2  Enable
4.1  Copy Unknown
4.2  Skip Unknown
9.1  Wait HDD Time
9.2  Copy HPA Area
6.1  Turn On
6.2  Mute

ESC
OK2014/10/07     09:506. Setup
7.1  English
7.2  Chinese
1.2  ALL Partitions
8.  Stop...

Page 16

www.aleratec.com10
Overview
Subfunctions
The “Log Manager” menu has one subfunction:
1.  Advanced Function

ESC
OK2014/10/07     09:507. Log Manager
1.1  Clear ALL Log
1.2  Set Password  

Page 17

www.aleratec.com11
Using the HDD Copy Cruiser High-Speed WL 
Main Menu
Copy
The “Copy” function performs a copy from a source HDD to one or more target 
HDDs. The target HDDs must be at least as large as the source. The HDD Copy 
Cruiser High-Speed WL will copy every block of capacity on the source HDD. 
1. Load the source HDD and the target HDDs into the HDD Copy Cruiser High-
Speed WL. The system will auto-detect the hard drives. After the drives have 
been detected, a screen similar to the one below...

Page 18

www.aleratec.com12
Using the HDD Copy Cruiser High-Speed WL 
Main Menu
Copy - Continued
3. During the copy process the HDD Copy Cruiser High-Speed WL will display 
progress information.
 
The amount of data remaining to be transferred (shown in gigabytes), and time 
will be displayed as the percentage of completion increases. 
Note: The copying speed, capacity and duration may vary from one hard drive to another. 
4. Once duplication is complete, a job status screen will be displayed.

ESC
OKPass: 1...

Page 19

www.aleratec.com13
Using the HDD Copy Cruiser High-Speed WL 
Main Menu
Compare
The “Compare” function performs a comparison of data from the source hard drive 
to the data on the target hard drives. 
1. With the source and target HDDs loaded use the arrow buttons (or) to 
select “Compare”. The following screen will be displayed. 
2. Press OK to begin the comparison. The system will auto-detect the hard drives.  
 
 
 
 
During the compare process, the HDD Copy Cruiser High-Speed WL will 
display...

Page 20

www.aleratec.com14
Using the HDD Copy Cruiser High-Speed WL 
Main Menu
Compare - Continued
3. When the comparison is completed, a job status screen will be displayed.

ESC
OKPass: 11  Fail: 0
Time: 20:18  
Start reading Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide

Related Manuals for Aleratec 111 HDD Copy Cruiser HighSpeed WL User Guide

All Aleratec manuals