Aleratec 11 HDD Cruiser Hard Disk Drive Duplicator and Sanitizer User Guide

www.aleratec.com15
Using the 1:1 HDD C\Cr\fiser 
Main Men\f
PreSca\f Source
The “PreScan Source” scans the source hard drive to determine if it can be read 
correctly.  
1. With the source HDD loaded, use the arrow buttons ( or) to select “PreScan 
Source”. The following screen will be displayed. 
2.  Press ENT to begin the scan. The system will auto-detect the hard drives. 
During the PreScan process, the 1:1 HDD Cruiser will display progress 
information. 
3.  When the PreScan is complete, a job...

www.aleratec.com16
Using the 1:1 HDD C\Cr\fiser 
Main Men\f
ReSca\f Bus
The “ReScan Bus” function causes the 1:1 HDD Cruiser to redetect connected hard 
drives. This can be used when you change drives without restarting the system. 
1. Use the arrow buttons (or) to select “ReScan BUS”. The following screen 
will be displayed.  
2.  Press ENT to select. The system will prompt you to confirm that you wish to 
proceed.  
3.  Press ENT 	to begin the rescan, during which the following screen will be...

www.aleratec.com17
Using the 1:1 HDD C\Cr\fiser 
Main Men\f
Source HDD Size
The “Source size” function is used to display the capacity of the source hard drive. 
1. With the source HDD loaded, use the arrow buttons ( or) to select “Source 
size”. The following screen will be displayed.  
2.  Press ENT 	to display the capacity of the source hard drive. 
ENTESC


5. So\frce size
ENTESC


Total: 232.5GB  

www.aleratec.com18
Using the 1:1 HDD C\Cr\fiser 
Main Men\f
Secure Erase
The “Secure Erase” function will sanitize (wipe clean of all data) the hard disk 
drives connected to the 1:1 HDD Copy Cruiser using algorithms programmed by 
the hard drive manufacturer.  Since this function is native to the hard drive, it is very 
fast and reliable.  Almost all modern SATA hard drives support this feature.  In the 
rare case that Secure Erase is not supported, please use the “Overwrite” function to 
sanitize your...

www.aleratec.com19
ENTESC


1 HDD          CH:0\C
Wipe s\fccessf\fl
 
 
5.  You can now scroll up and down for the individual status of each drive.
    

www.aleratec.com20
Using the 1:1 HDD C\Cr\fiser 
Main Men\f
Overwrite
The “Overwrite” function will sanitize (wipe clean of all data) the hard disk drives 
connected to the 1:1 HDD Copy Cruiser. 
1. Load the source HDD and the target HDDs into the 1:1 HDD Cruiser. The 
system will auto-detect the hard drives. Using the arrow buttons ( or) 
select “Overwrite”. The following screen will be displayed. 
Note: Overwriti\fg the e\fti\Pre capacity of all\P co\f\fected hard dri\Pves ca\f 
take a\f exte\fded...

www.aleratec.com21
Using the 1:1 HDD C\Cr\fiser  
b. To perform a “Three Pass Overwrite”, scroll to “3 Pass” and press ENT. 
This method will write one pass of 1’s, one pass of zeros, and one pass of  
randomly generated data. 
The next screen allows you to choose whether you wish to verify the 
random overwrite. 
Use the arrow buttons to toggle between “On” and “Off”. Press ENT to 
select.
c. To perform a “Seven Pass Overwrite”, scroll to “7 Pass” and press ENT. 
The following screen will be displayed....

www.aleratec.com22
Using the 1:1 HDD C\Cr\fiser 
Main Men\f
Setup
The “Setup” menu contains configuration options for the 1:1 HDD Copy Cruiser. It 
is suggested to use the factory defaults for optimum performance. 
1.  Use the arrow buttons (or) to select “Setup”. Press  ENT to select. The 
following screen will be displayed. 
Note: After cha\fgi\fg a\fy of\P the co\ffiguratio\f op\Ptio\fs, you must pre\Pss 
ENT to accept the cha\P\fge. O\fce all cha\fges\P are complete, pre\Pss ESC 
to exit the Setup...

www.aleratec.com23
Using the 1:1 HDD C\Cr\fiser 
Set\fp Men\f
8-01 La\fguage
This option allows you to select the language that is used for the display. 
1.  Use the arrow buttons (or) select “Setup”. The following screen will 
be displayed. 
2.  Use the arrow buttons () to scroll to “Language”. The following 
screen will be displayed. 
3.  Press ENT to display the current language selection (the default language 
is English). 
4.  Use the arrow buttons () to toggle through the available options....

www.aleratec.com24
Using the 1:1 HDD C\Cr\fiser 
Set\fp Men\f
8-02 Copy Size
This function is used to specify the amount of source disk data to copy to the 
target drives. 
1. Use the arrow buttons (or) select “Setup”, then press  ENT. The 
following screen will be displayed. 
2.  Use the arrow buttons () to scroll to “Copy Size”. The following 
screen will be displayed. 
3.  Press ENT to display the current configuration setting. 
4.  Use the arrow buttons () to toggle through the available copy...