Alarm Lock PDL3000 ETPDL PDL3500 Programming Instructions User Manual

21 
; 4 5 : 45. Enable Passage Mode (This Function enabled through keypad only) 
; 4 6 : 46. Disable Passage Mode (This Function enabled through keypad only) 
47. Timed Passage Mode (This Function enabled through keypad only) 
; 4 7      ; [ _ _ _ ] :  
(XXX Hours) 
•Function 45 allows passage through the door without the need for a User Code.  Re-Lock using Function 46.   
•Programmed Schedules will override the state of the lock when Functions 45 and 46 are used.  If it is required that 
programmed...

22 
49. Disable Permanent Passage Mode (This Function enabled through keypad only) 
50. Return Lock to Normal Passage 
Mode Schedule 
(This Function enabled through keypad only) (Locks will lock or unlock depending on the current schedule).  Use Function 50 to undo Functions 48 and/
or 49, and therefore return the lock to all pre-existing scheduled functions. 
•Function 48 allows passage through the door without the need for a User Code.  Re-Lock using Function 49. 
•Programmed Schedules will not...

23 
; 5 5 : 
; 5 7 :  57. Print Clock Settings, Software 
Version and Door Number
 
  
55. Print Audit Trail  
; 5 6 :  56. Print User Code List  
; 5 8 : 58. Upload/Download PC Data 
Hold the printer over the locks infrared sensor as shown in Figure 1 and Figure 2 above.  
Twenty (20) events will print at a time; press 1 for more events, or 9 to quit.  To abort 
printing, press any key for 3 seconds (three short beeps will sound). 
Hold the printer over the locks infrared sensor as shown in Figure 1 and...

24 
60. Number of Attempts Before Lockout  
61. Set the Attempts Lockout Time 
•Number of attempts before lockout must be 1-9 attempts. 
•The number of attempts is reduced by half every time the keypad is locked out without a 
successful code entry (default is 6 attempts).   
•The attempt count is reset each time a valid code is entered. 
•Lockout Time must be 1-60 seconds. 
How long the keypad is locked-out after a series of unsuccessful attempts 
(default is 18 seconds).  
 4 
 4 
LOCKOUT 
; 6 4 :  64....

25 
 
; 6 7    ; [ _ _ ] : 
        (Event Number) 67. Add System Features 
SYSTEM FEATURES 
68. Delete All Relay Features added by Function 67.   ; 6 8   ; 0 0 0 : 
•Relay Features (12-24. Reserved)  
1.     Remote Input switch closed and Function 65 Remote Input enabled.  
Because the Remote Input is enabled by factory default, the Relay will 
energize when the Remote Input switch is closed.   7.    Scheduled Lock Event.  Relay energizes for 2 seconds when lock is 
locked by a Schedule. 
2.     Remote...

26 
Scheduled Passage and Group 
Use the functions below to enable Passage Mode and enable/disable Groups at the time programmed. 
•For day enter: 1 for Sunday, 2 for Monday, 3 for Tuesday, 4 for Wednesday, 5 for Thursday, 6 for Friday, 7 for Saturday, 8 for Monday to Friday, 9 for Saturday and Sunday, and 0 for all days of week. 
SCHEDULES 
74. Schedule Enable Group 1 ; 7 4      ; [ _ ]           ; [ _ _ _ _ ] : 
                                         (Day)                                (Time) 
75....

27 
QUICK SCHEDULES 
84. Business Quick Schedule 
7AM-5PM, Monday - Friday (This Function enabled through keypad only) 
; 8 4      ; [ _ ] :  
(Group)  
; 8 5      ; [ _ ] :  
(Group)  85. Day Quick Schedule  
7AM-5PM, All days (This Function enabled through keypad only) 
; 8 6      ; [ _ ] :  
(Group)  86. Evening Quick Schedule 
3PM-1AM, All days (This Function enabled through keypad only) 
; 8 7      ; [ _ ] :  
(Group)  87. Night Quick Schedule 
11PM-9AM, All days (This Function enabled through...

28 
To Disarm a Burglary Control Panel 
90. Relay Activation  
(Open Time Window)
 
; 9 0      ; [ _ ]           ; [ _ _ _ _ ] : 
                                          (Day)                                      (Time) 
Functions 90 and 91 allow you to set up a window of time where if any Group 1 User Code is entered within this window, 
the relay will be activated for 2 seconds.  This relay is for use with a Control Panel that has a key switch disarm option.  For 
additional information, see Group 1...

29 
; 9 9      ; 0 0 0 :  99. Clear All Lock Programming (This Function enabled through keypad only) 
Clears all programming, and returns lock to factory default settings.  Audit Trail contents 
are maintained.  M 
CLEAR ALL PROGRAMMING 
94 - 98. Reserved 
92. Enable Group 4  
(Open Time Window) 
(This Function enabled through keypad only) 
; 9 2      ; [ _ ]           ; [ _ _ _ _ ] : 
                                       (Day)                                      (Time) 
Functions 92 and 93 allow you...

30 
Groups and Scheduled Group 1 Examples  
The following examples detail the more advanced features of the PDL series locks.  Although all features and device functions can be programmed 
using the lock keypad, when programming becomes more complex you may find it easier to use DL-Windows software to program your Alarm Lock 
security lock.  For more information, contact your Alarm Lock security professional. 
 
Assign a User to Two Groups 
Create a User 101 (all Users 101-150 are members of Group 2 by...