Alarm Lock PDK3000 Programming Instructions User Manual

							21 
GROUPS 
Group Enable/Disable with Timeout (Enter Timeout, XXX Hours) (Functions 25-34 are enabled through the keypad only) 
•Hours must be between 1-999.  Enter the functions below to Enable/Disable Groups for the amount of time entered in hours. 
         NOTE:   Only 4 Timeout Functions are allowed at any one time.  An error beep will sound when attempting to program more than 
4 Timeout Functions.  Functions 25 - 34 will each override existing scheduled events.  Therefore, Functions 25 - 34 are tem-
porary, take effect immediately, and are always overridden by future scheduled events that already exist within the lock 
programming.  NOTE:  Functions 25-34 are enabled through the keypad only. 
 
•Example:  All 15 members of the Accounting Department are members of Group 4, and a schedule programmed in the 
departments door lock reflects their normal working hours of 9 AM through 5 PM, Monday through Friday.  But one day a 
special event occurs, and all Accounting Department members are requested to stay an extra hour until 6 PM.  Therefore, 
at 5 PM, the manager (wishing to temporarily enable Group 4 users for an extra hour) enters Program Mode and 
presses:  ; 33   ; 001 :.  Likewise, if the manager wished to send his department home 
early at 3 PM, the manager could enter  ; 28   ; 002 :.  
 2 
;  3 5      ; [ _ _ _ ]           ; [ _ _ _ _ ] : 
   (User Number)                   (Groups) 35. Group Add/Delete Association 
As per the chart on page 8, the locks default programming from the factory associates certain User Numbers with certain 
Groups.  To override these default Group associations, Function 35 manually associates (or disassociates) a selected 
User with a selected Group.  During programming, Groups not selected are then disassociated from the User.  Function 
35 is helpful when the number of Users you wish to add to a Group outgrows the number of User Numbers defaulted to a 
Group (50); or if an existing User joins a department and you wish to simply add them to a Group. 
•User Number must be between 2 and 2000; Groups 1-4 (to associate with User) may be selected. 
 Add Example: To associate User 67 with Groups 1, 2 and 4;   Enter: ; 3 5      ; 6 7     ; 1 2 4 : 
Delete Example: To remove all Group associations for User 67;  
 Enter: ; 3 5      ; 6 7 :  NOTE:  If a User is associated with more than one Group, all associated Groups would have to be disabled before the User is disabled. 
; 2 5      ; [ _ _ _ ] : 
(XXX Hours) 25. Timed Disable Group 1   
; 2 6      ; [ _ _ _ ] : 
(XXX Hours) 26. Timed Disable Group 2   
; 2 7      ; [ _ _ _ ] : 
  (XXX Hours) 27. Timed Disable Group 3   
; 2 8      ; [ _ _ _ ] : 
  (XXX Hours) 28. Timed Disable Group 4   
; 2 9      ; [ _ _ _ ] : 
  (XXX Hours) 29. Timed Disable All Groups   
; 3 0      ; [ _ _ _ ] : 
  (XXX Hours) 30. Timed Enable Group 1   
; 3 1      ; [ _ _ _ ] : 
  (XXX Hours) 31. Timed Enable Group 2   
; 3 2      ; [ _ _ _ ] : 
  (XXX Hours) 32. Timed Enable Group 3   
; 3 3      ; [ _ _ _ ] : 
  (XXX Hours) 33. Timed Enable Group 4   
; 3 4      ; [ _ _ _ ] : 
  (XXX Hours) 34. Timed Enable All Groups   
 3 
36 - 37. Reserved 
Clear All Timeout Functions by entering Function 13. NOTE:  
Programming Functions (contd)  
						

							22 
; 3 8      ; [ _ _ _ _ _ _ ] :  
  
(Date) 
38. Set Date 
•Use Month Day Year format - MMDDYY - Single digit months and days are entered with a preceding zero. 
•Enter ONLY the last two digits of the year. 
 
For Example: March 8, 2009; Enter:  
 ; 3 8      ; 0 3   0 8    0 9 : 
 3 
39. Set Time ; 3 9      ; [ _ _ _ _ ] :  
  
(Time) 
•Time must be 4 digits 
•Use 24 Hour Format (add 12 hours to program PM time) 
 
For Example:  To set time to 8:25PM;  
 
 
 
Enter: ; 3 9      ; 2 0 2 5 :  For Example:  To set time to 8:25AM;   
 
 
Enter: ; 3 9      ; 0 8 2 5 : 
 3 
; 4 0      ; [ _ ] :  
  (Day) 40. Set Weekday 
•For day enter: 1 for Sunday, 2 for Monday, 3 for Tuesday, 4 for Wednesday, 5 for Thursday, 6 for Friday and 7 for Saturday.  For Example:  To set day to Sunday;   
 
 
Enter: ; 4 0      ; 1 : 
 3 
41. Daylight Saving Time Start Date ; 4 1 ; [ M M W D ] :  
(DST Starting Month, Month, Week, Day) 
The manner in which Daylight Saving Time (DST) is observed varies with location, therefore the DST adjustment is fully flexible to 
accommodate these regional differences.  Function 41 allows the entry of a DST Start Date (month, day and week), and Function 42 
allows the entry of a DST End Date (month, day and week).  DST begins and ends at 2AM on the programmed date.  Enter ; 
4 1 ; 0 0 0 : to disable DST.  All locks leave the factory with DST enabled and pre-programmed to the 
following start and end dates (for the USA beginning 2007): 
 
•Default DST Start Date: March, Week 2, Sunday (Second Sunday in March) 
•Default DST End Date:   November, Week 1, Sunday (First Sunday in November)  To program the DST start date using the keypad, press:  ; 4 1 ; [ M M W D ] : where M M W D represents:  
•M M = Two digits of the month (01 through 12 = January through December.  Single digit months are entered with a 
preceding zero). 
•W = Single digit for week of the month (valid entries are 1-5 where 1 is the first week, 2 is the second week, 3 is the 
third week, 4 is the fourth week and 5 is the last week of the month. 
•D = Day of the week (valid entries are 1-7:  1 for Sunday, 2 for Monday, 3 for Tuesday, 4 for Wednesday, 5 for Thursday, 6 
for Friday and 7 for Saturday).   
 Example:  To set the default start date of second Sunday in March, press:  
                ; 4 1 ; [ 0 3 2 1 ] : (03 = March,  2 = 2nd week, 1 = Sunday). 
 4 
CLOCK SETTINGS 
Programming Functions (contd) 
42. Daylight Saving Time End Date ; 4 2 ; [ M M W D ] :  
(DST Ending Month, Month, Week, Day) 
End date of Daylight Saving Time (month, week, day).  Enter ; 4 2 ; 0 0 0 : to disable DST.  
See Function 41 for full explanation.  4  
						

							23 
; 4 3           ; [ _  _ ] :  
(seconds) 
43. Speed Up Clock (This Function enabled through keypad only) 
; 4 4           ; [ _  _ ] :  
(seconds) 
44. Slow Down Clock (This Function enabled through keypad only) 
; 4 5 : 45. Enable Passage Mode (This Function enabled through keypad only) 
; 4 6 : 46. Disable Passage Mode (This Function enabled through keypad only) 
47. Timed Passage Mode (This Function enabled through keypad only) 
; 4 7      ; [ _ _ _ ] :  
(XXX Hours) 
•Function 45 allows passage through the door without the need for a User Code.  Re-Lock using Function 46.   
•Programmed Schedules will override the state of the lock when Functions 45 and 46 are used.  If it is required that 
programmed schedules do not override Passage Mode, enable/disable Passage Mode using Functions 48/49.  Note:  Be-
cause of the temporary nature of these features, Functions 45-47 can only be enabled using the keypad. 
Passage Mode Enable/Disable - Schedule will Override  
 2 
•Hours must be between 1 - 999. Function 47 allows passage through the door without the need for a User Code for the programmed amount of time.  
 
 
 
•For example, if you wish your office door lock to be unlocked (unlocked = Passage Mode) for the next 3 hours, 
enter Program Mode and press:  ; 47 ; 003 :     
 2 
PASSAGE MODE 
CLOCK ADJUST 
Number of seconds to adjust (speed up/slow down) the clock each day must be be-
tween 0-55 seconds. 
Note:  Repeated use of these Functions are not cumulative (this means, for example, 
if the clock has already been set to speed up 10 seconds per day, and then is found to 
need an additional 10 seconds, then program 20 seconds using Function 43). 
 
Example 1:  Clock is losing 13 seconds every day, enter: 
 ; 4 3       ; 1 3 :.  
This example assumes that the Clock Adjust setting was at the factory default of zero.  
Function 57 can be used to print the current Clock Adjust setting. 
 
Example 2:  Clock is gaining 13 seconds every day, enter: 
 ; 4 4       ; 1 3 :.  
This example assumes that the Clock Adjust setting was at the factory default of zero. 
Function 57 can be used to print the current Clock Adjust setting. 
 
Example 3:  To set the clock adjust setting back to the factory default of zero, enter
:  ; 4 3 :  or ; 4 4 : 
Clock Adjust  
 4 
Programming Functions (contd) 
Clock Accuracy 
The internal oscillator is factory calibrated to an accu-
racy of ±5 minutes/year.  Changes in ambient tem-
perature may affect accuracy.  If necessary, the ac-
curacy of the internal clock may be adjusted by first up-
dating the correct time via Function 39.  After an interval 
of about 1 month, re-set the correct time via Function 39 
and then print an Audit Log via Function 55.  Because 
the Audit Log displays both the New Clock Time and 
the Old Clock Time, a daily accuracy (in seconds) can 
be determined by taking the difference in seconds be-
tween the Old and New times divided by the number 
of days between the two Function 39 entries.  Note:  
Because the minimum available adjustment is 1 second 
per day, the inaccuracy of the clock must exceed about 6 
minutes per year before adjustment is necessary.  
						

							24 
49. Disable Permanent Passage Mode (This Function enabled through keypad only) 
50. Return Lock to Normal Passage 
Mode Schedule 
(This Function enabled through keypad only) (Locks will lock or unlock depending on the current schedule).  Use Function 50 to undo Functions 48 and/
or 49, and therefore return the lock to all pre-existing scheduled functions. 
•Function 48 allows passage through the door without the need for a User Code.  Re-Lock using Function 49. 
•Programmed Schedules will not override the state of the lock using functions 48 and 49.  If it is required that programmed 
schedules override Passage Mode, Enable/Disable Passage Mode using Functions 45/46.  Use Function 50 to undo Func-
tions 48 and/or 49, and therefore return the lock to all pre-existing scheduled functions.  Note:  Functions 48-50 can only be 
enabled using the keypad.  Warning:  Function 49 will inhibit all scheduled Passage Mode events. 
Passage Mode Enable/Disable - Schedule will not Override 
 2 
PERMANENT PASSAGE MODE 
; 4 9 :  
48. Enable Permanent Passage Mode (This Function enabled through keypad only)  
; 4 8 :  
; 5 0 :  
; 5 2 : 52. Set Pass Time to 3 Sec.        
; 5 3 : 
; 5 4 : 
The Pass Time is the length of time the lock stays unlocked after a valid User Code is 
entered.  When the Pass Time expires, the lock will re-lock automatically.  Use the 
functions below to change the Pass Time to 3, 10 or 15 seconds.  The Pass Time is 
defaulted to 3 seconds.   
Pass Time 
 4 
53. Set Pass Time to 10 Sec.        
54. Set Pass Time to 15 Sec.        
PASS TIME 
See Scheduled functions 72 and 73 for Scheduled Passage Mode. NOTE:  
Programming Functions (contd) 
51. Passage Mode Configuration  ; 5 1 ;     [ _ ]    : 
(Mode)  
•Mode 1 (Normal):  Passage Mode must be enabled/disabled using Function 45 and 46.  Mode 1 (Normal) is the factory de-
fault. 
•Mode 2:  Group 2 toggles Passage Mode. 
•Mode 3:  Group 2 enables, Group 3 disables Passage Mode.  Disable Passage Mode has priority if User is a member of both 
Groups 2 and 3. 
 
 
 
     With Mode 2, each time any member of Group 2 enters their User Code, they will toggle Passage Mode.  For example, if Pas-
sage Mode is enabled, and a Group 2 User enters their User Code, Passage Mode will be disabled.  If a few seconds later they 
enter their User Code again, Passage Mode will be enabled.  With Mode 3, Group 2 members will always enable Passage Mode, 
and Group 3 members will always disable Passage Mode.  For example, if Passage Mode is already enabled, and a Group 2 
User enters their User Code, the Passage Mode status will not be changed due to the Function 51 Mode 3 configuration.  If Pas-
sage Mode is already enabled, and a Group 3 User enters their User Code, Passage Mode will become disabled. 
 4  
						

							25 
; 5 5 : 
; 5 7 :  57. Print Clock Settings, Software 
Version and Door Number
 
  
55. Print Audit Trail  
; 5 6 :  56. Print User Code List  
; 5 8 : 58. Upload/Download PC Data 
Hold the printer over the locks infrared sensor as shown in Figure 1 and Figure 2 above.  
Twenty (20) events will print at a time; press 1 for more events, or 9 to quit.  To abort 
printing, press any key for 3 seconds (three short beeps will sound). 
Hold the printer over the locks infrared sensor as shown in Figure 1 and Figure 2 above.  
To abort printing, press any key for 3 seconds (three short beeps will sound). 
Hold the printer over the locks infrared sensor as shown in Figure 1 and Figure 2 above. 
For use with DL-WINDOWS software, refer to OI237.  AL-PCI interface cable is needed. 
 1 
 3 
 3 
PRINTER 
DOWNLOADING 
Hold the printer perpendicular to the Lock’s infrared LED as shown in Figure 1 and Figure 2.  If the 
printer has been idle for some time, press the paper feed button to wake up the printer. 
 1 
Programming Functions (contd) 
Infrared 
LED 
Figure 2 
Infrared 
LED 
Infrared 
Reader 
Place Infrared Reader (on printer) in 
front of the Infrared LED (on lock) 
Figure 1 
PDK3000 to Printer  
- Side View  
						

							26 
60. Number of Attempts Before Lockout  
61. Set the Attempts Lockout Time 
•Number of attempts before lockout must be 1-9 attempts. 
•The number of attempts is reduced by half every time the keypad is locked out without a 
successful code entry (default is 6 attempts).   
•The attempt count is reset each time a valid code is entered. 
•Lockout Time must be 1-60 seconds. 
How long the keypad is locked-out after a series of unsuccessful attempts 
(default is 18 seconds).  
 4 
 4 
LOCKOUT 
; 6 4 :  64. Disable Remote Input 
•Wire a Normally Open Contact to Wires (White & White) for a Remote Input.  Momentarily close 
switch to unlock the lock to allow person to pass through door.  This Remote Input can be used to 
control the Aux Relay.  See the Aux Relay System Features on page 27 (Function 67). 
•Enter the functions below to Disable/Enable the Remote Input.   
NOTE:  The Remote Input is enabled in the factory default. 
Remote Input  
; 6 5 : 65. Enable Remote Input 
; 6 6      ; [ _  _ ] :  
(Ambush Code) 
66. Ambush Code 
•Ambush code must be 2 digits. 
•An error will sound if the Ambush Code matches the 1st two digits of any User Code.  
See Function 67 for more information about the Ambush Function. 
 2 
 3 
REMOTE INPUT 
AMBUSH 
; 6 0      ; [ _ ] :  
(Number of Attempts) 
; 6 1     ; [ _ _ ] :  
(Lockout Time) 
62-63. Reserved 
Programming Functions (contd) 
59. Reserved  
						

							27 
 
; 6 7    ; [ _ _ ] : 
        (Event Number) 67. Add System Features 
SYSTEM FEATURES 
68. Delete All Relay Features added by Function 67.   ; 6 8   ; 0 0 0 : 
•Aux Relay Features (12-24. Reserved)  
1.      Remote Input switch closed and Function 65 Remote Input enabled.  
Because the Remote Input is enabled by factory default, the Main Relay will 
energize when the Remote Input switch is closed.  Additionally, if this event (#1) 
is then programmed, the Aux Relay will also close for 2 seconds upon closure 
of the Remote Input switch.   7.     Scheduled Lock Event.  Aux Relay energizes for 2 seconds when lock is 
locked by a Schedule. 
2.      Remote Input switch closed and Function 64 Remote Input disabled.  If 
the Remote Input is disabled with Function 64, the Main Relay will NOT ener-
gize when the Remote Input Switch is closed.  Additionally, if this event (#2) is 
then programmed, the Aux Relay will close for 2 seconds upon closure of the 
Remote Input switch.  The Main Relay will not energize. 8.     Scheduled Unlock Event.  Aux Relay energizes for 2 seconds when lock is 
unlocked by a schedule 
3.      Failed attempted entry.  Aux Relay energizes for 2 seconds when an at-
tempted User Code entry (or Pr o xCar d / K e yf ob )   fails. 9.     Lock Out.  Aux Relay energizes for 2 seconds when a Lock Out occurs (i.e. 
number of attempts is exceeded, see Function 60). 
4.     Disabled User or Group.  Aux Relay energizes for 2 seconds when a disabled 
User or disabled Group member enters a User Code (or P r oxC a r d/ K eyf o b ) . 10.    Ambush.  Aux Relay energizes for 2 seconds when Ambush is tripped.  See 
Function 66, page 26. 
5.     Follow Main/Entry Relay--Momentary Only.  When the Main/Entry Relay 
energizes for any length of time, the Aux Relay energizes for only 2 seconds.  
(Note:  The Aux relay will NOT energize with the Remote Input).  Compare with 
Event 31. 11.    First Key Press.  Aux Relay energizes for 2 seconds at the first key press of 
any sequence. 
6.      Group 1 User Code.  Aux Relay energizes for 2 seconds when a scheduled 
Group 1 User Code (or P r o x Car d / K e yf ob )  is entered.  See Function 90, page 
30. 31.    Follow Access Granted--No Time Limit.**  When the Main/Entry relay ener-
gizes for any length of time (such as a valid User Code entered or Remote 
Input), the Aux Relay energizes for the same amount of time as the pro-
grammed Pass Time.  (The Pass Time is the length of time the lock 
stays unlocked after a valid User Code is entered.  See functions 52-
5 4 ).   Use this feature for remote monitoring or other activation as this feature 
works independently of all other relay options.  Programming this feature will 
supersede all other programmed relay features.  Subsequent relay feature 
programming will not take effect while this feature is active.  Before program-
ming any other relay features, press ; 6 8 ; 0 0 
0 : to delete this feature.  
Use Function 67 to program one or more lock events and the Aux Relay will energize when the programmed event(s) listed below 
occurs.  For example, program ; 6 7 ; 3 : and when an attempted entry fails (such as a User who enters 
an incorrect or un-programmed User Code), the Aux Relay will energize for 2 seconds.  Note:  For more information about the Re-
mote Input, see page 11 (Wiring, Remote Input) and page 26 (Function 65).  
 
 4 
•System Options  
25.  Disable Sounder 
26.  5 sec. Delayed Entry * 
27.  15 sec. Delayed Entry * 
28.  45 sec. Delayed Entry * 
•Remote Input Functions 
29. Toggle Passage Mode.  Remote Input toggles Passage 
Mode.  Passage Mode enabled = Main/Entry Relay energized. 
30. Forced Unlock Follows Remote Input.**  When Remote 
Input activated, the Main/Entry Relay will energize regardless 
of its current state. 
32. Remote Input Disables Unit.**  Regardless of the current 
state, that state will remain unchanged (and keypad will be 
disabled) for the duration of Remote Input switch closure. 
*  Features 26, 27 & 28 will delay User Codes 12 and higher only (except 297, 298 and 299). 
** Sustained closure of remote input may affect proper audit trail operation. 
NOTE:  Enter ; 6 7 ; 0 0 0 : to delete all Relay Features added by Function 67 (identical to Function 68).
 
•PC Communication Functions 
33.  Remote Input Puts Unit in PC Communication Mode 
Enter ; 6 8   ; 0 0 0 : to delete all Relay Features added by Function 67.    4 
Programming Functions (contd) 
Ambush Function 1.  Connect relay to a device able to properly monitor dry contacts for an Ambush condition. 
2.  Program the Relay for Ambush Tripped using Program Function 67(10) above. 
3.  Set the Ambush Code using Program Function 66.  
4.  W hen the Ambush Code is entered followed by a valid User Code, the relay will close for 2 seconds. 
Notes:  The Ambush Code defaults to 99.  An error will sound if you try to program a new User Code starting with the Ambush Code.  
						

							28 
Scheduled Passage and Group 
Use the functions below to enable Passage Mode and enable/disable Groups at the time programmed. 
•For day enter: 1 for Sunday, 2 for Monday, 3 for Tuesday, 4 for Wednesday, 5 for Thursday, 6 for Friday, 7 for Saturday, 8 for Monday to Friday, 9 for Saturday and Sunday, and 0 for all days of week. 
SCHEDULES 
74. Schedule Enable Group 1 ; 7 4      ; [ _ ]           ; [ _ _ _ _ ] : 
                                         (Day)                                (Time) 
75. Schedule Enable Group 2 ; 7 5      ; [ _ ]           ; [ _ _ _ _ ] : 
(Day)                                (Time) 
76. Schedule Enable Group 3 ; 7 6      ; [ _ ]           ; [ _ _ _ _ ] : 
                                         (Day)                                (Time) 
77. Schedule Enable Group 4 ; 7 7      ; [ _ ]           ; [ _ _ _ _ ] : 
                                         (Day)                                (Time) 
78. Schedule Enable All Groups ; 7 8      ; [ _ ]           ; [ _ _ _ _ ] : 
                                   (Day)                                (Time) 
79. Schedule Disable Group 1 ; 7 9      ; [ _ ]           ; [ _ _ _ _ ] : 
                                   (Day)                                (Time) 
80. Schedule Disable Group 2 ; 8 0      ; [ _ ]           ; [ _ _ _ _ ] : 
                                   (Day)                                (Time) 
81. Schedule Disable Group 3 ; 8 1      ; [ _ ]           ; [ _ _ _ _ ] : 
                                   (Day)                                (Time) 
82. Schedule Disable Group 4 ; 8 2      ; [ _ ]           ; [ _ _ _ _ ] : 
                                   (Day)                                (Time) 
83. Schedule Disable All Groups ; 8 3      ; [ _ ]           ; [ _ _ _ _ ] : 
                                         (Day)                                (Time) 
 3 
Clear All Schedule and Timeout Functions by entering Function 12. 
  To set the time, see Function 39.   NOTE:  
72. Schedule Enable Passage 
Mode (Unlock)
 
; 7 2      ; [ _ ]           ; [ _ _ _ _ ] : 
(Day)                              (Time) 
73. Schedule Disable Passage 
Mode (Lock)
 
; 7 3      ; [ _ ]           ; [ _ _ _ _ ] : 
(Day)                              (Time) 
Groups 
ENTER KEY 
•When this function is enabled, the User must press : after any valid User Code entry.  Therefore, 
this Function allows User Codes to be subsets of other User Codes. 
 Examples:   1 2 3 : can be a valid user code;  
1 2 3 4 : can be a valid user code within the same lock. 
1 2 3 4 5 6 :
 (Hold ;) for Master User Code to enter Program Mode. 
Enter Key  
 4
 
71. Reserved 
Passage 
Mode 
69. Enable : as Enter Key  
70. Disable : as Enter Key 
Programming Functions (contd) 
; 6 9 : 
 
; 7 0
 :  
						

							29 
QUICK SCHEDULES 
84. Business Quick Schedule 
7AM-5PM, Monday - Friday (This Function enabled through keypad only) 
; 8 4      ; [ _ ] :  
(Group)  
; 8 5      ; [ _ ] :  
(Group)  85. Day Quick Schedule  
7AM-5PM, All days (This Function enabled through keypad only) 
; 8 6      ; [ _ ] :  
(Group)  86. Evening Quick Schedule 
3PM-1AM, All days (This Function enabled through keypad only) 
; 8 7      ; [ _ ] :  
(Group)  87. Night Quick Schedule 
11PM-9AM, All days (This Function enabled through keypad only) 
88. Passage Mode  
(Open Time Window)
 
(This Function enabled through keypad only) 
; 8 8      ; [ _ ]           ; [ _ _ _ _ ] : 
                                          (Day)                                      (Time) 
Functions 88 and 89 allow you to set up a window of time where if any Group 1 User Code is entered within this window, 
Passage Mode will be activated, allowing anyone to enter.  Note:  This feature can only be programmed using the lock key-
pad.  For additional information, see Group 1 Activated Features on page 30. 
 
•For the day enter: 1 for Sunday
, 2 for Monday, 3 for Tuesday, 4 for Wednesday, 5 for Thursday, 6 for Friday, 7 for Saturday, 8 for Monday to Friday, 9 for Saturday and Sunday, and 0 for all days of week.  •Enter time of day in 24 hour format (for example, for 2:15 PM, enter 14:15). 
Note:  Do not use this feature in Residency mode. 
Scheduled Passage Mode (Group 1 Activated)  
89. Passage Mode 
(Close Time Window)
 (This Function enabled through keypad only) 
; 8 9      ; [ _ ]           ; [ _ _ _ _ ] : 
                                          (Day)                                       (Time) 
SCHEDULES GROUP 1 ACTIVATED 
 3 
For your convenience, your lock comes pre-programmed with Quick Schedules, which, when programmed, enable Groups for 
popular blocks of time.  Group members will be enabled during the blocks of time defined below, but will still need to enter their 
User Codes into the keypad to unlock the lock.   
•Group number must be 1-4; enter the number of the Group that is to be enabled for the time specified by the Quick 
Schedules below. 
 Note:  These Quick Schedules can only be programmed through the keypad (not through DL-Windows), and existing Quick 
Schedules will be over-written by schedules downloaded from DL-Windows.  Therefore, after downloading any DL-Windows 
schedules, be sure to re-program your Quick Schedules into your Lock Program. 
 3 
Quick Schedules - Enable Group 
Programming Functions (contd)  
						

							30 
To Disarm a Burglary Control Panel 
90. Relay Activation  
(Open Time Window)
 
; 9 0      ; [ _ ]           ; [ _ _ _ _ ] : 
                                          (Day)                                      (Time) 
Functions 90 and 91 allow you to set up a window of time where if any Group 1 User Code is entered within this window, 
the relay will be activated for 2 seconds.  This relay is for use with a Control Panel that has a key switch disarm option.  For 
additional information, see Group 1 Activated Features on page 32. 
 
•Also program Relay Function 6 using Function 67 (; 6 7      ; 6 :). 
•For day enter: 1 for Sunday
, 2 for Monday, 3 for Tuesday, 4 for Wednesday, 5 for Thursday, 6 for Friday, 7 for Saturday, 
8 for Monday to Friday, 9 for Saturday and Sunday, and 0 for all days of week. 
•Enter time of day in 24 hour format (for example, for 2:15 PM, enter 14:15). 
Scheduled Relay Activation (Group 1 Activated)  
; 9 1      ; [ _ ]           ; [ _ _ _ _ ] : 
                                          (Day)                                       (Time) 
91. Relay Activation  
(Close Time Window)
 
SCHEDULES GROUP 1 ACTIVATED 
 3 
NOTES  1.  Group 1 Disarms a Burglary Control 
Panel will always disarm an alarm 
system.  Arming should be performed 
by other means (such as Alarm Panel 
Keypad/Schedule). 
 
2.  Use a qualified electrical/alarm 
specialist to review your current alarm 
system and add additional components 
as needed (such as a relay, wire, 
resistors, connectors and/or diodes) and 
re-program the operation of your alarm 
system as needed. 
 
Programming Functions (contd) 
Alarm Panel with Switched Input for Disarming 
Alarm Panel with Switched Input for Toggled Arm/Disarm 
Burglary 
Control 
Panel 
Switch  
Input Relay  
Output 
Burglary 
Control 
Panel Switch  
Input Relay  
Output 
 
Armed 
Lug Power