Home > Alarm Lock > Alarm Lock > Alarm Lock Inside Battery Kit for Narrow Locks User Manual

Alarm Lock Inside Battery Kit for Narrow Locks User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Alarm Lock Inside Battery Kit for Narrow Locks User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 84 Alarm Lock manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							16.   Make sure the Battery Connec-
    tor Wire is routed through the 
    correct hole to meet up with the 
    center oval hole drilled in step 10. 
    INSIDE BATTERY KIT  
    INSTALLATION INSTRUCTIONS 
    WI1516  2/06 
    345 Bayview Avenue 
    Amityville, New York 11701 
    For Sales and Repairs 1-800-ALA-LOCK 
    For Technical Service 1-800-645-9440 
    © ALARM LOCK 2006      Publicly traded on NASDAQ  Symbol: NSSC      www.alarmlock.com 
    7. Secure the Bat-
    tery Mounting 
    Bracket using the 
    top door mount-
    ing screw that is 
    located away 
    from the edge of 
    the door. 
    6.     Remove lock from door.   
    8.  Using a center-
    punch, mark two 
    holes for drilling: 
    •Mark the bottom 
    Bracket hole for 
    securing the 
    Mounting Bracket 
    (shown) 
    --and-- 
    •Mark in the center 
    oval for routing the 
    remote battery 
    wires. 
    9.   Use  a  #21  drill  for 
    both the bottom 
    Bracket hole 
    (shown), and the 
    center oval.   
    11.   Tap #10-32 threads into the bot-
    tom Bracket hole drilled in step 9.   
         Now the locks Rear Cover Plate 
    must be removed, as shown in step 
    12: 
    12.   Remove the flat-head mounting 
    screws located at both ends of the 
    lock.   
    13.  With the Rear Cover Plate 
    separated from the lock body, 
    find and disconnect the Battery 
    Pack Connector. 14.   Battery Pack Connector wire is 
    glued in two locations (shown).  
    Carefully lift and remove wire from 
    glue to detach. 15.   Replace the Rear Cover Plate.  
    Route the Battery Connector Wire 
    through the correct hole as shown 
    in step 16.   
    3.    Unscrew four through-door 
    mounting screws (in two door 
    plates) that secure the lock to the 
    door. 2.    Remove the decorative door 
    plate covers by sliding them up 
    from the door plates. 
    4. Remove Latch 
    Face Plate. 
    5.  Deadbolt models only:  Loosen 
    the interface cylinder set screw 
    (skip this step for springlatch 
    models).   
    Decorative door 
    plate covers 
    Door Plate 
    Some installations require the batteries powering the door lock be placed inside the protected premises.  The following in-
    structions describe how to install the Inside Battery Kit for your narrow stile door lock. 
    Set Screw 
    Bottom 
    Bracket Hole 
    1.     Loosen the battery cover screw 
    and slide the battery cover off the 
    lock.   
    Battery Cover 
    Screw 
    Glue Glue 
    Align the 
    Engager pin 
    and the 
    Driver hole 
    Mark 
    here 
    Battery 
    Connector 
    Wire 
    Battery Pack Connector 
    10.   Enlarge the center 
    oval hole to 7/16.  
    This center oval hole 
    is the only hole that 
    must be drilled all the 
    way through the 
    door.   
        Note:  Remove the 
    Battery Mounting 
    Bracket before 
    enlarging this hole. 
    Enlarge to 7/16 Center Oval 
    continued  
    						
    							17.   Replace all screws removed in 
    step 12, securing the Rear Cover 
    Plate. 18.   From outside the door, route the 
    Battery Pack Connector wire through 
    the 7/16 center oval through hole 
    drilled in step 10.   
    22.   Place the 
    battery pack 
    inside the 
    bracket.  Be sure 
    the batteries are 
    fresh.   
    19.   Use needle-nose pliers (or simi-
    lar tool) to pull the plug through the 
    7/16 center oval through hole 
    drilled in step 10. 
    20.     Secure  the 
    through-door 
    mounting screw 
    (in its door plate), 
    further securing 
    the lock to the 
    door.  Install its 
    decorative door 
    plate cover by 
    sliding it over the 
    door plate. 
    21.   Replace  the 
    Mounting Bracket 
    and secure with 
    both the through-
    door mounting 
    screws and the 
    10-32 screw 
    (provided). 
        Connect the bat-
    tery pack plug to 
    the battery wire.   
    23.   Place the 
    battery cover 
    over the Battery 
    Mounting 
    Bracket using 
    the two screws 
    provided.   
    Door Plate 
    Battery 
    Wire 
    24.   Be sure to use 
    the second bottom 
    screw to secure 
    cover.    
    						
    All Alarm Lock manuals Comments (0)

    Related Manuals for Alarm Lock Inside Battery Kit for Narrow Locks User Manual