Alarm Lock DL3500 DL3500EX ETDL DL3200 Programming Instructions User Manual

11 
WIRING 
See the Installation Manual for more information.  
Batteries: 
Use only 1.5 volt Duracell Alkaline size-AA batteries. 
 
External Power: 
Red / Black wires - External 7.5 VDC Power Source 
must be used for operation without batteries. 
 
Remote Input: 
White / White wires - Wire a Normally Open Contact 
to wires (white and white).  Momentarily close to allow 
person to pass through door.  NOTE:  Remote Input 
is enabled from the factory.  (See page 23) 
 
Relay: 
COM-Blue / NO-Yellow /...

12 
Quick Start 
First Time Start Up 
1.    Unpack the lock. 
2.    With the batteries disconnected, hold down the ; key for 10 seconds and release. 
3.    Connect the batteries and listen for 3 beeps.  Within 5 seconds of hearing the 3 beeps, press and hold ; until beeping 
starts.  This will clear the lock of all programmed data.  Important:  If you do not hear these 3 beeps, you must start over at 
step 2.   
4.   Listen for another series of beeps and LED flashes followed by 10 seconds of silence....

13 
Quick Start (cont’d) 
      The lock will flash a green LED and beep continuously for 6 seconds.  When the red LED flashes, the User Code is deleted. 
3.   Repeat step 2 for each new User.   
 
User Code Conflicts 
Care should be taken not to program a new User Code which matches the first digits of any other User Code (only the User 
Code with the least number of digits will be recognized).  Example:  If User Codes 123 and 123456 are both entered in the 
system, only code 123 would be recognized,...

14 
Function 1 Change Master Code See page 15 
Function 2 Add/Delete/Change User Codes See page 15 
Function 3 User Disable (By User Number) See page 16 
Function 4 User Enable (By User Number) See page 16 
Function 5 User Enable with Timeout  See page 16 
Function 6 Enable Total User Lockout See page 16 
Function 7 Disable Total User Lockout See page 16 
Function 8 Reserved - 
Function 9 Enable User 300 (Service Code) See page 16 
Function 10 Erase All Users Except the 
Master Code See page 16 
Function...

15 
1. New Master Code (User Number 1) 
2. Add/Delete/Change User Codes 2-2000  
; 1      ; [ _ _ _ _ _ _ ]           ; [ _ _ _ _ _ _ ] : 
   (New Master Code)                  (Confirm New Master Code) 
; 2      ; [ _ _ _ _ ]  *              ; [ _ _ _ _ _ _ ] : 
(User Number)                                    (User Code) 
•User Number must be between 2 and 2000. 
•To delete a code, leave the User Code blank and wait for the rapid beeping to stop. 
•User Code must be 3-6 digits. 
•Each User Code can be...

16 
USERS (Continued) 
; 6 :  6. Enable Total User Lockout Mode (This Function enabled through keypad only) 
7. Disable Total User Lockout Mode (This Function enabled through keypad only) 
; 7 : 
User Lockout Mode  
Prevents all User Codes (Except User 1 Code) from operating the lock.  Note: No other programming 
functions or schedules will re-enable Users.  Users must be re-enabled with Function 7. 
Note:  Does not change the User enable/disable status.  Note:  If the lock is currently in Passage Mode...

17 
; 1 2      ; 0 0 0 :  12. Clear All Schedules and Timeout Functions 
Function 12 clears all programmed Schedules and all Timeout Functions.  (To clear All Timeout Functions only, see 
Function 13 below).  Function 12 will clear all of the following:  All Schedule Functions 72 through 93, Timeout Functions 
5, 25 through 34 and Function 47.  Note:  Function 12 also resets Passage Mode and any disabled Groups.  After using 
Function 12, your Scheduled/Timeout features must be manually re-programmed....

18 
GROUPS 
Group Enable/Disable with Timeout (Enter Timeout, XXX Hours) (Functions 25-34 are enabled through the keypad only) 
•Hours must be between 1-999.  Enter the functions below to Enable/Disable Groups for the amount of time entered in hours. 
         NOTE:   Only 4 Timeout Functions are allowed at any one time.  An error beep will sound when attempting to program more than 
4 Timeout Functions.  Functions 25 - 34 will each override existing scheduled events.  Therefore, Functions 25 - 34 are...

19 
; 3 8      ; [ _ _ _ _ _ _ ] :  
  
(Date) 
38. Set Date 
42. Reserved  
•Use Month Day Year format - MMDDYY - Single digit months and days are entered with 
a preceding zero. 
•Enter ONLY the last two digits of the year. 
 
For Example: March 8, 2002; 
 Enter:   ; 3 8      ; 0 3   0 8    0 2 : 
 3 
39. Set Time ; 3 9      ; [ _ _ _ _ ] :  
  
(Time) 
•Time must be 4 digits 
•Use 24 Hour Format (add 12 hours to program PM time) 
 
For Example:  To set time to 8:25 PM;  
 
 
 
Enter: ; 3 9      ; 2 0...

20 
CLOCK ADJUST 
; 4 3           ; [ _  _ ] :  
(seconds) 
43. Speed Up Clock (This Function enabled through keypad only) 
; 4 4           ; [ _  _ ] :  
(seconds) 
44. Slow Down Clock (This Function enabled through keypad only) 
Number of seconds to adjust (speed up/slow down) the clock each day must be between 
0-55 seconds. 
Always consider the current setting when using this function, because this function is not 
cumulative.  For example, if the clock needs to be sped up 10 seconds per day and the...