Air Live Router WT-2000AP User Manual

							AirLive  WT-2000AP User’s  Manual 29 
c. Choose Disable DNS in the DNS Configuration tab. 
 
B. Configure IP manually 
a. Select Specify  an  IP  address in  the  IP  Address  tab.  The  default  IP  address  of  this 
product  is 192.168.1.254.  So  please  use  192.168.1.xxx (xxx is between  1 and  253) for 
IP Address field and 255.255.255.0 for Subnet Mask field. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
b. In  the  Gateway  tab,  add  the  IP  address  of  this  product  (default  IP  is 192.168.1.254)  in 
the New gateway field and click Add button.  
						

							 AirLive WT-2000AP User’s Manual 30 
 
 
c. In  the  DNS  Configuration  tab,  add  the  DNS  values  which  are  provided  by  the  ISP  into 
DNS Server Search Order field and click Add button. 
     
 
 
 
                                                                                                     
						

							AirLive  WT-2000AP User’s  Manual 31 
AAAppppppeeennndddiiixxx   BBB   888000222...111xxx   SSSeeettttttiiinnnggg   
 
 Figure 1: Testing Environment (Use Windows 2000 Radius Server) 
1 Equipment Details 
PC1:  
Microsoft Windows XP Professional without Service Pack 1. 
AMIT 531C Wireless Cardbus:3.0.3.0 
Driver version:  
PC2:  
Microsoft Windows XP Professional with Service Pack 1a or latter. 
AMIT 561C Wireless Cardbus:1.0.1.0 
Driver version: 1.7.29.0 (Driver date: 10.20.2001) 
Authentication Server: Windows 2000 RADIUS server with Service Pack 3 and HotFix Q313664. 
  Note. W indows 2000 RADIUS server only supports PEAP after upgrade to service pack 3 and    
  HotFix Q313664 (You can get more information from     
  http://support.microsoft.com/default.aspx?scid=kb; en-us;313664) 
2 DUT  
Configuration: 
1.Enable DHCP server. 
2.LAN IP address: 192.168.1.254/24. 
3.Set RADIUS server IP. 
4.Set RADIUS server shared key. 
5.Configure W EP key and 802.1X setting. 
 
The  following  test  will  use  the  inbuilt  802.1X  authentication  method  such  as  ,EAP_TLS, 
PEAP_CHAPv2(Windows XP with SP1 only), and PEAP_TLS(Windows XP with SP1 only) using 
the Smart Card or other Certificate of the W indows XP Professional. 
 
3. DUT and Windows 2000 Radius Server Setup 
3-1-1.  Setup W indows 2000 RADIUS Server 
We have to change authentication method to MD5_Challenge or using smart  
card or other certificate on RADIUS server according to the test condition.  
						

							 AirLive WT-2000AP User’s Manual 32 
3-1-2.  Setup DUT 
1.Enable the 802.1X (check the “Enable checkbox“). 
2.Enter the RADIUS server IP. 
3.Enter the shared key. (The key shared by the RADIUS server and DUT). 
4.We will change 802.1X encryption key length to fit the variable test  
condition. 
3-1-3.  Setup Network adapter on PC 
1.Choose the IEEE802.1X as the authentication method. (Fig 2) 
Note.  
Figure 2 is a setting picture of Windows XP without service pack 1. If users 
upgrade to service pack 1, then they can’t see MD5-Challenge from EAP type 
list any more, but they will get a new Protected EAP (PEAP) option. 
2.Choose MD5-Challenge or Smart Card or other Certificate as the EAP 
type. 
3.If choosing use smart card or the certificate as the EAP type, we select to  
use a certificate on this computer. (Fig 3) 
   4. We will change EAP type to fit the variable test condition. 
 
Figure 2: Enable IEEE 802.1X access control 
 
 
  
						

							AirLive  WT-2000AP User’s  Manual 33 
 
4. Windows 2000 RADIUS server Authentication testing: 
 
4.1DUT authenticate PC1 using certificate. (PC2 follows the same test procedures.) 
1. Download and install the certificate on PC1. (Fig 4) 
2. PC1 choose the SSID of DUT as the Access Point. 
3. Set authentication type of wireless client and RADIUS server both to  
EAP_TLS. 
4. Disable the wireless connection and enable again. 
5. The DUT will send the users certificate to the RADIUS server, and then 
send the message of authentication result to PC1. (Fig 5) 
6. Windows XP will prompt that the authentication process is success or fail  
and end the authentication procedure. ( Fig 6) 
7. Terminate the test steps when PC1 get dynamic IP and PING remote host  
successfully. 
 Figure 4: Certificate information on PC1 
 
  
						

							 AirLive WT-2000AP User’s Manual 34 
Figure 5: Authenticating 
 
 
Figure 6: Authentication success 
 
4.2DUT authenticate PC2 using PEAP-TLS. 
1. PC2 choose the SSID of DUT as the Access Point. 
2. Set authentication type of wireless client and RADIUS server both to  
PEAP_TLS. 
3. Disable the wireless connection and enable again. 
4.The DUT will send the users certificate to the RADIUS server, and then 
send the message of authentication result to PC2. 
5. Windows XP will prompt that the authentication process is success or fail  
and end the authentication procedure. 
6. Terminate the test steps when PC2 get dynamic IP and PING remote host  
successfully. 
Support Type: The AP supports the types of  802.1x Authentication: 
              PEAP-CHAPv2 and PEAP-TLS. 
Note: 
1.PC1 is on W indows XP platform without Service Pack 1. 
2.PC2 is on W indows XP platform with Service Pack 1a. 
3.PEAP is supported on Windows XP with Service Pack 1 only. 
4.Windows XP with Service Pack 1 allows 802.1x authentication only when data encryption 
function is enable. 
 
 
 
 
 
 
 
 
 
 
 
  
						

							AirLive  WT-2000AP User’s  Manual 35 
AAAppppppeeennndddiiixxx   CCC   WWWDDDSSS   SSSeeettttttiiinnnggg   
 
How to setup and work: 
First, check the Wlan-mac address of AP1,AP2 and AP3.Please goto command mode and use  
“Arp –a ”. 
If you can not find the information of Mac, please make the cable to plug in lan-port of ap and ping the 
lan ip address then arp –a. There are some information in the screen. For example: 
    
 
AP 1:                                                  AP2:                                        AP3: 
IP:192.168.1.254                           IP:192.168.1.253                  IP:192.168.1.252 
Mac:00-50-18-00-0f-fe                      Mac:00-50-18-00-0f-fd            Mac:00-50-18-00-0f-fc 
SSID:Default                                      SSID:Default                            SSID:Default 
Channel:11                                        Channel:11                                Channel:11 
Dhcp Server:Enable 
 
 
 
 
 
 
 
 
 
 
  
						

							 AirLive WT-2000AP User’s Manual 36 
Blue Line:W ireless 
Black Line:W ire                 
 
 
If the Settings are ok,the client1 and client2 can get ip from dhcp server of    AP1.Then Client1 and  
Client2 can get information each other. 
 
AP1 Setting: 
AP1 AP2(Remote Mac: 00-50-18-00-0f-fd) 
AP1 AP3(Remote Mac: 00-50-18-00-0f-fc) 
 
 
  
						

							AirLive  WT-2000AP User’s  Manual 37 
 
 
AP2 Setting: 
AP2 AP1(Remote Mac: 00-50-18-00-0f-fe) 
 
 
 
AP3 Setting 
AP3 AP1(Remote Mac: 00-50-18-00-0f-fe) 
 
 
 
 
 
 
 
  
						

							 AirLive WT-2000AP User’s Manual 38 
 
AAAppppppeeennndddiiixxx   DDD   FFFAAAQQQ   aaannnddd   TTTrrrooouuubbbllleeessshhhooooootttiiinnnggg   
 
 
How do I connect AP by using wireless? 
 
1.How to start to use wireless? 
A: First, make sure that you already installed wireless client device in your computer. Then check the      
Configuration of wireless router. The default is as below:  
 
 
About wireless client, you will see wireless icon: 
 
Then click and will see the ap list that wireless client can be accessed: 
 
If the client can not access  your  wireless router,  please refresh network list again. However, I still can 
not fine the device which ssid is “default”, please refer to Q3. 
 
Choose the one that you will want to connect and Connect: