Air Live Router WT-2000AP User Manual

							AirLive  WT-2000AP User’s  Manual 19 
WPA/WPA2 
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the 
Wireless user must authenticate to this router first to use the Network service. RADIUS Server 
The router will detect automatically    which Security type(Wpa-psk version 1 or 2) the client  
uses to encrypt. 
IP address or the 802.1X server’s domain-name.  
Select RADIUS Shared Key 
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits 
If ASCII, the length of Pre-share key is from 8 to 63. 
Key value shared by the RADIUS server and this router. This key value is consistent with the key value 
in the RADIUS server. 
 
 
 
WDS(Wireless Distribution System)    
WDS operation as defined bythe IEEE802.11 standard has been made available. Using WDS it is 
possible to wirelessly connect Access Points, and in doing so extend a wired infrastructure to locations 
where cabling is not possible or inefficient to implement.  
						

							 AirLive WT-2000AP User’s Manual 20 
  
 
 
  
 
4.6.4 MAC Address Control (Basic Setting Wireless Setting) 
 
 
MAC  Address  Control  allows  you  to  assign  different  access  right  for  different  users  and  to  assign  a 
specific IP address to a certain MAC address. 
MAC Address Control Check  “Enable”  to  enable  the  “MAC  Address  Control”.  All  of  the 
settings in this page will take effect only when “Enable” is checked. 
Connection control Check  Connection  control  to  enable  the  controlling  of  which  wired  and 
wireless clients can connect to this device. If a client is denied to connect to 
this  device,  it  means  the  client  cant  access  to  the  Internet  either.  Choose  
						

							AirLive  WT-2000AP User’s  Manual 21 
allow or deny to allow or deny the clients, whose MAC addresses are not 
in the Control table (please see below), to connect to this device. 
Association control Check Association control to enable the 
controlling of which wireless client can 
associate to the wireless LAN. If a client is 
denied to associate to the wireless LAN, it 
means the client cant send or receive any data 
via this device. Choose allow or deny to 
allow or deny the clients, whose MAC 
addresses are not in the Control table, to 
associate to the wireless LAN. 
Control table 
 
 
 Control table is the table at the bottom of the MAC Address Control page. Each row of this 
table indicates the MAC address and the expected IP address mapping of a client. There are 
four columns in this table: 
 
MAC Address MAC address indicates a specific client. 
IP Address Expected IP address of the corresponding 
client. Keep it empty if you dont care its IP 
address. 
C When Connection control is checked, 
check C will allow the corresponding 
client to connect to this device. 
A When Association control is checked, 
check A will allow the corresponding 
client to associate to the wireless LAN. 
 
In this page, we provide the following Combobox and button to help you to input the MAC address. 
 
You can select a specific client in the “DHCP clients” Combobox, and then click on the “Copy to” button 
to copy the MAC address of the client you select to the ID selected in the “ID” Combobox. 
 
 
Previous page and Next Page  
To make this setup page simple and clear, we have divided the “Control table” into several pages.  
You can use these buttons to navigate to different pages.  
						

							 AirLive WT-2000AP User’s Manual 22 
4.7 Advanced Settings 
 
 
4.7.1 System Time 
  
Set Date and Time using PC’s Date and Time 
Use PC Date and Time as Machine 
Set Date and Time manually 
Selected if you want to Set Date and Time manually.  
  
						

							AirLive  WT-2000AP User’s  Manual 23 
4.8 Maintenance 
 
 
 
 
4.8.1 Change Password 
 
 
You can change Password here. We strongly recommend you to change the system password for 
security reason. 
 
  
						

							 AirLive WT-2000AP User’s Manual 24 
4.8.2 View Log 
 
 
 
You can View system log by clicking the View Log button 
 
4.8.3 Firmware Upgrade 
 
 
 
You can upgrade firmware by clicking Firmware Upgrade button. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							AirLive  WT-2000AP User’s  Manual 25 
4.8.4 Backup Setting 
 
 
 
You can backup your settings by clicking the Backup Setting button and save it as a bin file. Once you 
want to restore these settings, please click Firmware Upgrade button and use the bin file you saved. 
 
4.8.5 Reset to default 
 
 
 
You can also reset this product to factory default by clicking the Reset to default button. 
 
4.8.6 Reboot 
 
 
 
You can also reboot this product by clicking the Reboot button. 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							 AirLive WT-2000AP User’s Manual 26 
AAAppppppeeennndddiiixxx   AAA   TTTCCCPPP///IIIPPP   CCCooonnnfffiiiggguuurrraaatttiiiooonnn   fffooorrr   WWWiiinnndddooowwwsss   
999555///999888   
This  section  introduces  you  how  to  install  TCP/IP  protocol  into  your  personal  computer.  And  suppose 
you have been successfully installed one network card on  your personal computer. If not, please refer 
to your network card manual. Moreover, the Section B.2 tells you how to set TCP/IP values for working 
with this NAT Router correctly. 
A.1 Install TCP/IP Protocol into Your PC 
1. Click Start button and choose Settings, then click Control Panel. 
2. Double click Network icon and select Configuration tab in the Network window. 
3. Click Add button to add network component into your PC. 
4. Double click Protocol to add TCP/IP protocol. 
 
 
5. Select Microsoft item in the manufactures list. And choose TCP/IP in the Network Protocols. Click 
OK button to return to Network window. 
 
6. The  TCP/IP  protocol  shall  be  listed  in  the  Network  window.  Click OK to  complete  the  install 
procedure and restart your PC to enable the TCP/IP protocol. 
 
A.2 Set TCP/IP Protocol for Working with NAT Router 
1. Click Start button and choose Settings, then click Control Panel. 
2. Double click Network icon. Select the TCP/IP line that has been associated to your network card in 
the Configuration tab of the Network window.  
						

							AirLive  WT-2000AP User’s  Manual 27 
 
 
3. Click Properties button to set the TCP/IP protocol for this NAT Router. 
4. Now, you have two setting methods:  
						

							 AirLive WT-2000AP User’s Manual 28 
 
a. Select Obtain an IP address automatically in the IP Address tab. 
 
b. Don’t input any value in the Gateway tab.