Air Live Router WL-5470AP User Manual

							AirLive WL_5470AP User’s Manual 
36 
4.9 GW Mode Setting 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Alias Name You can set the alias name for this device. limited not exceed 32 
characters 
… Disable Wireless 
LAN Interface Check the box to disable the Wireless LAN Interface.    By doing so, you won’t be 
able to make wireless connection with this Access Point in the network you are 
located. In other words, this device will not be visible by any wireless station. 
Band You can choose one mode of the following you need.       
~ 2.4GHz (B): 802.11b supported rate only. 
~ 2.4GHz (G): 802.11g supported rate only.   
~ 2.4GHz (B+G):802.11b supported rate and 802.11g supported rate. The 
default is 2.4GHz (B+G) mode. 
SSID The SSID differentiates one WLAN from another; therefore, all access points and 
Note:  You may need to scroll the window in the actual web browser display to view all items in 
GW Mode Settings.  
						

							                                                                     AirLive WL_5470AP User’s Manual 
37  all devices attempting to connect to a specific WLAN must use the same SSID. In 
WISP mode, you have to enter the WISP Outdoor AP 
SSID manually or click the “site survey” button to connect and get   
SSID automatically.   
Channel Number The number of channels supported depends on the region of this Access Point. All 
stations communicating with the Access Point must use the same channel.   
Wireless Client 
Isolation When enabled, the wireless clients are separated from each other.    Please refer 
the AP mode settingsÆ Wireless Client Isolation for details. 
Security Please refer the AP mode settingsÆ Security Survey for details. 
Advance Setting   Please refer the AP mode settingsÆ Advance Setting for details. 
WAN port Please refer the WISP mode settingsÆ WAN port Setting for details. 
Virtual Server Please refer the WISP mode settingsÆ Virtual Server Setting for details. 
Special Application Please refer the WISP mode settingsÆ Special Application Setting for details. 
DMZ Please refer the WISP mode settingsÆ DMZ Setting for details. 
Remote Management Please refer the WISP mode settingsÆ Remote Management Setting for details.
Dynamic DNS The DDNS (require DDNS Service) allows you to alias a dynamic IP address to a 
static hostname, allowing your device to be more easily accessed by specific 
name. When this function is enabled, the IP address in DDNS Server will be 
automatically updated with the new IP address provided by ISP. 
Ping Ping is a network tool used to test whether a particular host is reachable across an 
IP network. 
DoS setting In WL5470AP , a denial-of-service attack (DoS attack) can block or limit the 
system sending network flood to your local computer. 
Diagnostics The nslookup command can be used in diagnostics to find the IP addresses of a 
particular computer, using DNS lookup. The name means name server lookup. 
The most common version of the program is included as part of the BIND package.
URL Filtering The URL filter database is used for internet filtering that blocks access to 
unwanted web content by URLs. 
MAC Filtering MAC Filter: Enables you to allow or deny Internet access to users within the LAN 
based upon the MAC address of their network interface. 
IP Filtering The IP filter function enables you to define a minimum and maximum IP address 
range filter; all IP addresses falling within the range are not allowed Internet 
access 
 
 
 
 
 
  
						

							AirLive WL_5470AP User’s Manual 
38 
4.10 Status 
In this screen, you can see the current settings and status of this Access Point. You can change settings by 
selecting specific tab described in below. 
 
． System 
 
 
  
						

							                                                                     AirLive WL_5470AP User’s Manual 
39 
System 
Uptime  The time period since the device was up. 
Firmware Version  The current version of the firmware installed in this device.   
Wireless  
Mode  There are 7 modes supported, The default mode is Access Point. If you want to 
change to other mode, please click the Mode and select the wireless mode you 
want.  
Physical Address  Display wireless MAC address information. 
Band  Display wireless band type information. 
SSID  Display the SSID of this device. 
Channel Number  The number of channels supported depends on the region of this Access Point. All 
stations communicating with the Access Point must use the same channel. 
Encryption  Display encryption setting information. 
Associated Clients  Displays the total number of clients associated to this AP. You can have up to 64 
clients to associate to this Access Point.   
BSSID  BSSID displays the ID of current BSS, which uniquely identifies each BSS. In AP 
mode, this value is the MAC address of this Access Point. 
LAN Configuration (TCP/IP)   
Connection Method:    Display the connection method, you can setup in TCP/IP section 
Physical Address:    Display the LAN MAC address 
IP Address:    Display the LAN IP address, you can setup in TCP/IP section 
Network Mask:    Display the network mask, you can setup in TCP/IP section 
Default Gateway:    Display the default gateway ip , you can setup in TCP/IP section 
DHCP Server:    Default the DHCP Server is enabled(ON) 
DHCP Start IP 
Address:   Display the DHCP server start IP address. 
DHCP Finish IP 
Address:   Display the DHCP server finish IP address. 
Internet Configuration   
Connection Method:    Display the internet connection method, you can setup in WISP modeÆWAN 
 Port configuration 
Physical Address:  Display the AP MAC address information 
IP Address:  Display the internet IP Address, you can setup in WISP modeÆWAN 
 Port configuration 
Network Mask:  Display the network mask, you can setup in WISP modeÆWAN 
 Port configuration 
Default Gateway:  Display the default gateway , you can setup in WISP modeÆWAN 
 Port configuration 
  
						

							AirLive WL_5470AP User’s Manual 
40 
． Statistics 
 
The Statistics table shows the packets sent/received over wireless and ethernet LAN respectively. 
 
． Active Clients 
 
Display the active Wireless Clients information:   Wireless MAC address, Tx/Rx Packet, Tx Rate, and Power 
Saving information. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							                                                                     AirLive WL_5470AP User’s Manual 
41 
4.11 TCP/IP 
 
In this page, you can change the TCP/IP settings of this Access Point, select to enable/disable the DHCP 
Client, 802.1d Spanning Tree, and Clone MAC Address.   
IP Address This field can be modified only when DHCP Client is disabled. If your system 
manager assigned you static IP settings, then you will have to enter the 
information provided. 
Subnet Mask Enter the information provided by your system manager. 
Default Gateway Enter the information provided by your system manager.   
DHCP Select Disable, Client or Server from the pull-down menu. 
Disable: Select to disable DHCP server function.   
Client: Select to automatically get the LAN port IP address from ISP (For 
ADSL/Cable Modem). 
Server: Select to enable DHCP server function. 
DHCP Client Range WL-5060AP IP addresses continuing from 192.168.100.1 to 192.168.100.253 
Show Client Click to show Active DHCP Client table. 
DNS Server Enter the Domain Name Service IP address. 
802.1d Spanning Tree To enable 802.1d Spanning Tree will prevent the network from infinite loops. 
Infinite loop will happen in the network when WDS is enabled and there are 
multiple active paths between stations.    
						

							AirLive WL_5470AP User’s Manual 
42 
 
Clone MAC Address You can specify the MAC address of your Access Point to replace the factory
setting. 
 
4.12 Reboot 
Click the Reboot button to restart device. 
 
 
 
 
 
  
						

							                                                                     AirLive WL_5470AP User’s Manual 
43 
Chapter V: Other 
 
． Upgrade Firmware 
 
1.  Download the latest firmware from your distributor and save the file on the hard drive. 
2.  Start the browser, open the configuration page, click on Other, and click Upgrade Firmware to 
enter the Upgrade Firmware window. 
3.  Enter the new firmware’s path and file name (i.e. C:\FIRMWARE\firmware.bin) or click the Browse 
button to find and open the firmware file (the browser will display to correct file path). 
4. Click Upload button to start the upgrade function or Reset button to clear all the settings on this 
page. 
 
．  Save / Reload Settings 
 
This function enables users to save the current configuration as a file (i.e. config.dat) or loades 
configuration from a file. Enter the file name or click Browse… to find the file from your computer. 
     Save Settings to File: Click SAVE.. to save the current configuration to file. 
     Load Settings From File: Click Browse…  if you want to load a pre-saved file, enter the file name 
           with the correct path and then click on Upload or click Browse… to select the file.  
						

							AirLive WL_5470AP User’s Manual 
44 
  
     Reset Settings to Default: Click Reset button to restore the default configuration. 
． Password 
 
For secure reason, It is recommended that you set the account to access the web server of this Access Point. 
Leaving the password blank will disable the protection. The login screen prompts immediately once you finish 
setting password. Remember your password for you will be asked to enter them every time you access the 
web server of this Access Point. 
New Password Set your new password. Password can be up to 30 characters long. Password 
can contain letter, number and space. It is case sensitive. 
Confirm Password   Re-enter the new password for confirmation. 
Note: when you setup the password and click the apply change button, system will pop-up Window and ask 
the username and password, Please enter system default username “admin” (not changeable) and your 
password for entering the configuration WEB UI. 
． Log 
  
						

							                                                                     AirLive WL_5470AP User’s Manual 
45  This function can list all log information about device. 
Enable Log Enabled or Disabled display system log information. 
System All List system all log information. 
Wireless Only List wireless log information only. 
Refresh Refresh log information. 
Clear Clear all information in window. 
 
． NTP 
 
 
This function can setting system time from local computer or Internet. 
Current Time Setting system time   
Enable NTP client updateEnable or Disable setting system from Internet NTP Server. 
Time Zone Select Select system time zone. 
NTP Server Select NTP Server by Server List or Manual Input. 
Save Save configuration to flash. 
Reset Reset system time configuration. 
Refresh Refresh system time information.