Air Live Router WL-5470AP User Manual
Have a look at the manual Air Live Router WL-5470AP User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 15 Air Live manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
AirLive WL_5470AP User’s Manual 26 4.4 Bridge Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters. … Disable Wireless LAN Interface Check the box to disable the Wireless LAN Interface, by so doing, you won’t be able to make wireless connection with this Access Point in the network you are located. In other words, this device will not be visible by any wireless station. Band You can choose one mode of the following you need. ~ 2.4GHz (B): 802.11b supported rate only. ~ 2.4GHz (G): 802.11g supported rate only. ~ 2.4GHz (B+G):802.11b supported rate and 802.11g supported rate. The default is 2.4GHz (B+G) mode. Channel Number In Bridge mode, both wireless AP/Router device need set to the same Channel number. Security Please refer the AP mode settingsÆ Security for details. But bridge mode are not supported with RADIUS 802.1x authentication. WDS Security To enable security between wireless AP/Router , you can select WEP 64bits, WEP 128bits, WPA (TKIP), WPA2(AES) for data encryption. For WEP encryption, Select ASCII if you are using ASCII characters. Select HEXif you are using hexadecimal numbers (0-9, or A-F). For WPA/WPA2 encryption, you need enter the Pre-Shared Key Information for the authentication purpose.
AirLive WL_5470AP User’s Manual 27 Advance Setting Please refer the AP mode settingsÆ Advance Setting for details. AP MAC address Enter 12 digits in hex numbers in the AP MAC address (BSSID) field and press the Add MAC Address Button to associate with other’s Wireless access point. Before you want to use bridge mode to connect each other to provide A wireless bridge between 2 remote LANs, you need add the BSSID of other’s wireless AP first. Site Survey Site survey displays all the active Access Points and IBSS in the neighborhood. Press Site Survey button to search the wireless device. Add MAC Address Enter MAC address of remote access point. Reset Press to discard the data you have entered since last time you press Apply Change. Show Statistics List all packets information of traffic. Delete Selected To delete bridge from access to this Access Point, you may firstly check the Select checkbox next to the MAC address and Comments, and press Delete Selected. Delete All To delete all the clients from access to this Access Point, just press Delete All without selecting the checkbox.
AirLive WL_5470AP User’s Manual 28 4.5 WDS Repeater Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters. … Disable Wireless LAN Interface Check the box to disable the Wireless LAN Interface, by so doing, you won’t be able to make wireless connection with this Access Point in the network you are located. In other words, this device will not be visible by any wireless station. Band You can choose one mode of the following you need. ~ 2.4GHz (B): 802.11b supported rate only. ~ 2.4GHz (G): 802.11g supported rate only. ~ 2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate. The default is 2.4GHz (B+G) mode. SSID The SSID differentiates one WLAN from another; therefore, all access points and all devices attempting to connect to a specific WLAN must use the same SSID. It is case-sensitive and must not exceed 32 characters. A device will not be permitted to join the BSS unless it can provide the unique SSID. An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network Channel Number The number of channels supported depends on the region of this Access Point. All stations communicating with the Access Point must use the same channel. Wireless Client Isolation When enabled, the wireless clients are separated from each other. Please refer the AP mode settingsÆ Wireless Client Isolation for details. Security Please refer the AP mode settingsÆ Security for details,
AirLive WL_5470AP User’s Manual 29 This setting is use between Wireless client and this device. WDS Security Please refer to the Bridge mode settings Æ WDS Security for details This setting is use between both wireless AP/Router devices. Advance Setting Please refer the AP mode settingsÆ Advance Setting for details. Access Control Please refer the AP mode setting Æ Access Control for details. AP MAC Address Enter 12 digits in hex numbers in the AP MAC address (BSSID) field and press the Add MAC Address Button to associate with other’s Wireless access point. Before you want to use bridge mode to connect each other to provide A wireless bridge between 2 remote LANs, you need add the BSSID of other’s wireless AP first. Delete Selected To delete bridge from access to this Access Point, you may firstly check the Select checkbox next to the MAC address and Comments, and press Delete Selected. Delete All To delete all the clients from access to this Access Point, just press Delete All without selecting the checkbox.
AirLive WL_5470AP User’s Manual 30 4.6 Universal Repeater Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters. … Disable Wireless LAN Interface Check the box to disable the Wireless LAN Interface, by so doing, you won’t be able to make wireless connection with this Access Point in the network you are located. In other words, this device will not be visible by any wireless station. Band You can choose one mode of the following you need. ~ 2.4GHz (B): 802.11b supported rate only. ~ 2.4GHz (G): 802.11g supported rate only. ~2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate. The default is 2.4GHz (B+G) mode. SSID The SSID differentiates one WLAN from another; therefore, all access points and all devices attempting to connect to a specific WLAN must use the same SSID. It is case-sensitive and must not exceed 32 characters. A device will not be permitted to join the BSS unless it can provide the unique SSID. An SSID is also referred to as a network name because essentially it is a name that identifies a wireless network Channel Number The number of channels supported depends on the region of this Access Point. All stations communicating with the Access Point must use the same channel. SSID of extended Interface When in Universal Repeater mode, you have to enter the ESSID of other’s AP/Router that device want to connect. The device SSID and the SSID of extended interface can be the same or different. When you are using the universal repeater mode, please make sure the remote
AirLive WL_5470AP User’s Manual 31 AP/Router WDS function is turned off. Site Survey Please refer the Bridge mode settingsÆ Site Survey for details. Security Please refer the AP mode settingsÆ Security for details, This setting used Wireless client or remote AP to link this device. Advance Setting Please refer the AP mode settingsÆ Advance Setting for details. Access Control Please refer the AP mode setting Æ Access Control for details. 4.7 WISP (Client Router) Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters … Disable Wireless LAN Interface Check the box to disable the Wireless LAN Interface, by so doing, you won’t be able to make wireless connection with this Access Point in the network you are located. In other words, this device will not be visible by any wireless station. Band You can choose one mode of the following you need. ~ 2.4GHz (B): 802.11b supported rate only. ~ 2.4GHz (G): 802.11g supported rate only. ~ 2.4GHz (B+G):802.11b supported rate and 802.11g supported rate. The default is 2.4GHz (B+G) mode. SSID The SSID differentiates one WLAN from another; therefore, all access points and all devices attempting to connect to a specific WLAN must use the same SSID. In WISP mode, you have to enter the WISP Outdoor AP
AirLive WL_5470AP User’s Manual 32 SSID manually or click the “site survey” button to connect and get SSID automatically. Site Survey Please refer the Client mode settingsÆ Site Survey for details. MAC Clone Address Enter the MAC Address of Single Ethernet Client. Security Please refer the AP mode settingsÆ Security Survey for details. Not supported with RADIUS 802.1x authentication. Advance Setting Please refer the AP mode settingsÆ Advance Setting for details. WAN port You can select many WAN Access Type : Static IP , DHCP Client, PPPOE, PPTP, and L2TP for WAN connection depend on you WISP provided. Virtual Server In WISP mode, you can setup and enable Virtual server function. Like Web, FTP, Email, DNS, Telnet server. Select one virtual server type and enter the Local IP address, Local Port Range and click the save button.
AirLive WL_5470AP User’s Manual 33 Special Application You can enable some system default special application, like Qucktime 4 Audio/Video application, Dialpad internet phone service. or define the special application manually, select the incoming type (TCP/UDP) Incoming start ~ End port ,Trigger Start ~ End port. Select the Trigger Type. DMZ Enable DMZ and enter the DMZ Host IP address. Remote Management Enable the function that setting configuration from Internet.
AirLive WL_5470AP User’s Manual 34 4.8 WISP + Universal Repeater Mode Setting Alias Name You can set the alias name for this device. limited not exceed 32 characters … Disable Wireless LAN Interface Check the box to disable the Wireless LAN Interface, by so doing, you won’t be able to make wireless connection with this Access Point in the network you are located. In other words, this device will not be visible by any wireless station. Band You can choose one mode of the following you need. ~ 2.4GHz (B): 802.11b supported rate only. ~ 2.4GHz (G): 802.11g supported rate only. ~ 2.4GHz (B+G):802.11b supported rate and 802.11g supported rate. The default is 2.4GHz (B+G) mode. SSID The SSID differentiates one WLAN from another; therefore, all access points and all devices attempting to connect to a specific WLAN must use the same SSID. In WISP mode, you have to enter the WISP Outdoor AP SSID manually or click the “site survey” button to connect and get SSID automatically. Site Survey Please refer the Client mode settingsÆ Site Survey for details. SSID of extended Interface Please refer the Universal repeater mode settingsÆ SSID of extended Interface for details. MAC Clone Address Enter the MAC Address of Single Ethernet Client.
AirLive WL_5470AP User’s Manual 35 Enable Encryption On You can designate security to use for WLAN side, WAN side or both sides. Both WAN and WLAN side: The security is used on both the WISP and the Wireless Client(PC side) connection.. WLAN side only: The security used on wireless client connection only. The WISP side is not encrypted. WAN side only: The security used on WISP connection only. The WLAN side is not encrypted.. Security Please refer the AP mode settingsÆ Security Survey for details. Not supported with RADIUS 802.1x authentication. Advance Setting Please refer the AP mode settingsÆ Advance Setting for details. WAN port Please refer the WISP mode settingsÆ WAN port Setting for details. Virtual Server Please refer the WISP mode settingsÆ Virtual Server Setting for details. Special Application Please refer the WISP mode settingsÆ Special Application Setting for details. DMZ Please refer the WISP mode settingsÆ DMZ Setting for details. Remote Management Please refer the WISP mode settingsÆ Remote Management Setting for details.