Air Live Router WL-5470AP User Manual

AirLive WL_5470AP User’s Manual 
36 
4.9 GW Mode Setting 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Alias Name You can set the alias name for this device. limited not exceed 32 
characters 
… Disable Wireless 
LAN Interface Check the box to disable the Wireless LAN Interface.    By doing so, you won’t be 
able to make wireless connection with this Access Point in the network you are 
located. In other words, this device will not be visible by any wireless station. 
Band You can choose one...

                                                                     AirLive WL_5470AP User’s Manual 
37  all devices attempting to connect to a specific WLAN must use the same SSID. In 
WISP mode, you have to enter the WISP Outdoor AP 
SSID manually or click the “site survey” button to connect and get   
SSID automatically.   
Channel Number The number of channels supported depends on the region of this Access Point. All 
stations communicating with the Access Point must use the same channel....

AirLive WL_5470AP User’s Manual 
38 
4.10 Status 
In this screen, you can see the current settings and status of this Access Point. You can change settings by 
selecting specific tab described in below. 
 
． System 
 
 
  

                                                                     AirLive WL_5470AP User’s Manual 
39 
System 
Uptime  The time period since the device was up. 
Firmware Version  The current version of the firmware installed in this device.   
Wireless  
Mode  There are 7 modes supported, The default mode is Access Point. If you want to 
change to other mode, please click the Mode and select the wireless mode you 
want.  
Physical Address  Display wireless MAC address information. 
Band  Display...

AirLive WL_5470AP User’s Manual 
40 
． Statistics 
 
The Statistics table shows the packets sent/received over wireless and ethernet LAN respectively. 
 
． Active Clients 
 
Display the active Wireless Clients information:   Wireless MAC address, Tx/Rx Packet, Tx Rate, and Power 
Saving information. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

                                                                     AirLive WL_5470AP User’s Manual 
41 
4.11 TCP/IP 
 
In this page, you can change the TCP/IP settings of this Access Point, select to enable/disable the DHCP 
Client, 802.1d Spanning Tree, and Clone MAC Address.   
IP Address This field can be modified only when DHCP Client is disabled. If your system 
manager assigned you static IP settings, then you will have to enter the 
information provided. 
Subnet Mask Enter the information...

AirLive WL_5470AP User’s Manual 
42 
 
Clone MAC Address You can specify the MAC address of your Access Point to replace the factory
setting. 
 
4.12 Reboot 
Click the Reboot button to restart device. 
 
 
 
 
 
  

                                                                     AirLive WL_5470AP User’s Manual 
43 
Chapter V: Other 
 
． Upgrade Firmware 
 
1.  Download the latest firmware from your distributor and save the file on the hard drive. 
2.  Start the browser, open the configuration page, click on Other, and click Upgrade Firmware to 
enter the Upgrade Firmware window. 
3.  Enter the new firmware’s path and file name (i.e. C:\FIRMWARE\firmware.bin) or click the Browse 
button to find and open the...

AirLive WL_5470AP User’s Manual 
44 
  
     Reset Settings to Default: Click Reset button to restore the default configuration. 
． Password 
 
For secure reason, It is recommended that you set the account to access the web server of this Access Point. 
Leaving the password blank will disable the protection. The login screen prompts immediately once you finish 
setting password. Remember your password for you will be asked to enter them every time you access the 
web server of this Access Point. 
New...

                                                                     AirLive WL_5470AP User’s Manual 
45  This function can list all log information about device. 
Enable Log Enabled or Disabled display system log information. 
System All List system all log information. 
Wireless Only List wireless log information only. 
Refresh Refresh log information. 
Clear Clear all information in window. 
 
． NTP 
 
 
This function can setting system time from local computer or Internet. 
Current Time Setting...