Aiphone AXWAVTR Instructions User Manual

							CONFIGURATION DIAGRAM:  
AXW-AVT with Axis 243SA Video Server (Standalone Only)Configuration Notes:
1.  AX-series video door station connects to ‘DOOR’ input of AXW-AVT. 
Ensure that the “CCTV / DOOR’ switch on the AXW-AVT is in the ‘DOOR’ 
position. 
*2. Alternatively, an IE/IF-series or AX-DM audio door may be used, along 
with 3
rdparty CCTV camera.  Connect audio door station to ‘Door’ input 
(following the wiring method shown in the AX-series installation manual, 
pg. 12). Connect the camera to ‘Video In’ and put the ‘CCTV / DOOR’ 
switch in the ‘CCTV’ position.
3.  Connect the Call In / Call Out and Audio In / Audio Out connections on 
the AXW-AVT to the Axis 243SA connectors, as shown.
4.  Configure AXW-AVT internal jumpers as necessary (see Pg. 21).
Pg. 19Pg. 20Please Note:
Only information pertaining to the connection and operation of the AXW-AVT / AXW-AVR and listed 3
rdparty devices interfacing with it are included here. Aiphone is not 
responsible for attempts to connect the AXW-AVT / AXW-AVR to untested 3
rdparty transmission hardware. Consult the installation manual for the 3
rdparty device being utilized 
for further information regarding physical mounting, base functionality, power requirements,  etc.  For the most up-to-date compatibility information, please consult http://
www.aiphone.com or contact Aiphone Technical Support. 
For complete AX system installation, wiring, and programming information, please consult the AX Installation Manual (included on CD with AX Central Exchange Unit, or 
available at http://www.aiphone.com). 
CCTV Camera
75 Ohm, 1V Peak-to-peak
(Independently powered)
Normally Closed input for remote activation
(i.e. motion sensor, loop detector, etc.)Normally Open contact for remote device activation 
(i.e. video switcher, DVR, etc.)
AXW-AVT
24V
+
-
RELAY
NO
NO
SENSOR
NC
NC
CALL IN
+
-
CALL OUT
+
-
AUDIO IN
+
-
AUDIO OUT
+
-
DOOR
VIDEO IN
VIDEO OUT
AX-DVAX-DM or IE/IF-Series 
Audio Door Station
CAT-5eCoax
*
+
-
PS-2420UL
Axis 243SA
(Front View)
Coaxial Video Cable
Axis 243SA
(Back View)
To Network
Axis 243SA Application Considerations:
The Axis 243SA can only be used in ‘Standalone’ configuration (i.e., 
utilizing a PC as a master station).When used in standalone configuration, Aiphone recommends 
Controlware’s VIPDoorControl software.  For further details, see 
http://www.vipdoorcontrol.com
.
Consult the Axis 243SA Installation and User manuals for further 
information pertaining to video server installation and configuration.
NETWORK POWERSTATUS 75Ω ON 1  2  3  4
AXIS 243SA
Video Server
VIDEO
IN  OUT LINE
OUT LINE/MIC
IN
NETWORK
RS-232
POWER
1
23456789101112
To Axis-supplied 
power source 
						

							Pg. 21
CN3: Transmitting Gain
High / LowCN5: Muting Circuit
On / Off
CN4: Receive Gain
High / Low
AXW-AVT Internal Jumper Settings:
The AXW-AVT has three internal jumper settings to control the functionality and conditioning of the audio 
circuitry.  These should be adjusted as necessary, based on the selection of fiber / Ethernet equipment used.  
To access these jumpers, the chassis of the AXW-AVT will need to be opened.  Adjusting these jumper 
settings will NOT invalidate the AXW-AVT’s warranty.
Transmitting Gain (CN3): Controls the amount of amplification applied to the outgoing audio (‘Audio Out’) 
connection of the AXW-AVT.  A ‘Low’ setting provides no gain, whereas a ‘Hi’ 
setting applies approximately +10db of amplification.  Default position is ‘Low.’
Receive Gain (CN4): Controls the amount of amplification applied to the incoming audio (‘Audio In’) 
connection of the AXW-AVT.  A ‘Low’ setting provides no gain, whereas a ‘Hi’ 
setting applies approximately +10db of amplification.  Default position is ‘Low.’
Muting Circuit (CN5): The ‘Muting Circuit’ controls whether audio to/from the door station is 
completely full-duplex, or limited to one direction or the other (semi-duplex).  
This adjustment is required in situations where latency may be present between 
audio transmission and reception (i.e., Ethernet).  In such situations, the muting 
circuit should be set to ‘On’ to reduce audible echoing.  In situations where 
latency is not an issue (i.e., fiber, direct connections, etc.), this should be left in 
the default ‘Off’ position. 
						

							Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA  98005
(425) 455-0510
FAX (425) 455-0071
Toll Free Technical Support:
(800) 692-0200
E-mail [email protected]. 22
AXW-AVT,AVR Instr.
0311JD
Note:
Only information pertaining to the connection and operation of the AXW-AVT, AXW-AVR and devices interfacing with it 
are included here. Aiphone is not responsible for attempts to connect the AXW-AVT / AXW-AVR to untested 3
rdparty 
transmission hardware. For the most up-to-date compatibility information, please consult http://www.aiphone.com or 
contact Aiphone Technical Support. For complete installation, wiring, and programming information regarding the AX 
system, please refer to the AX Installation Manual, which is included on the CD provided with the AX CEU, or available 
for download at http://www.aiphone.com.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
and correct the interference by one or more of the following measures:
— Reorient or locate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC Class B Verification
SPECIFICATIONS:
Power:
AXW-AVT 24V DC, 500mA (use Aiphone PS-2420UL)
AXW-AVR Supplied by AX CEU
Video Input & Output: Composite 1V Peak-to-Peak, NTSC
Video Connectors: BNC 
Door input: RJ-45
Relay: Normally Open contact output; 30V DC, 1A
Sensor: Normally Closed contact input
Wire: CAT-5e, 24AWG UTP-4
Wiring distance:
AXW-AVT to Door, Max. 980 cumulative
AXW-AVR to CEU
AXW-AVT / -AVR to As close as possible; do not exceed 16
3
rdparty devices
Dimensions:
AXW-AVT + AXW-AVR 1-5/8H x 7W x 4D