Home > Aimco Brakes > Screwdrivers > Aimco Brakes Screwdriver AE2015 Screwdriver Operation Instructions User Manual

Aimco Brakes Screwdriver AE2015 Screwdriver Operation Instructions User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Aimco Brakes Screwdriver AE2015 Screwdriver Operation Instructions User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							PO Box 16460, Portland OR 97292 - 0460      800 - 852 - 1368      Fax 800 - 582 - 9015  
    www.aimco - global. com  Direct Plug - In Electric Screwdriver  
    Model AE - 2015  
    Operations Manual   
    						
    							- 1   -Outline  
     Before Using
     Check voltage .  Please read the label on the product exterior and the manual thoroughly before using the
    screwdriver, and make sure to correctly determine  the screwdriver’s voltage requirement (115VAC).  Only plug
    the screwdriver into an outlet with the correct voltage.
     Check for suitable torque range .  Choose a screwdriver model that matches your required torque range.  To
    lengthen product life, avoid usin g screwdrivers at maximum torque over long periods.
     Check that the carbon maintenance bonnet is closed tightly .  If the bonnet or spring connector have come
    loose, the motor will automatically cut off.  The screwdriver will operate only after they have be en correctly
    reassembled.  If the power cord is in any way damaged, unplug the screwdriver immediately and exchange it for
    a new product in order to protect against shocks or fire caused by a short circuit.
     Check the workplace .  Although this product feat ures dual insulation, to ensure safety, do not use it in damp or
    high - temperature environments or near flammable materials. Keep the power cord away from tools and
    equipment that might damage or melt it.
     Caution :  When plugging or unplugging the power cor d, make sure to hold it by the plug.  Never pull the power cord.
     Usage and Cautions
     Driving and removing screws .  To drive a screw, set the forward/reverse switch to
    the FWD position.  To remove a screw, set the switch to the REV position.
    ( Caution :    Never change the switch position when the motor is running! )
    Release the trigger (power switch) and change the position after the motor stops.
     Torque setting .  Set the torque level by rotating the regulating handle.  Turning it
    clockwise into the casing   will increase the torque and turning it counter - clockwise
    out of the casing will decrease the torque.  ( Caution :  The markings on the
    regulating handle are for reference only and do not indicate torque output.
    Actual torque can only be determined with a  torque - testing machine. )  If you
    have difficulty removing screws (reverse setting), increase torque by turning the
    regulating handle clockwise into the casing.
     Inserting the bit .  Push the bit slide sleeve down with your finger and insert a
    suitable bit.    When the bit slide sleeve is released, the bit will become engaged.  If
    the bit wobbles during operation, remove it, rotate it 30 or 180° and reinsert it as
    shown at right.  ( Caution :  Never force the bit in or out. ) 
    						
    							- 2   -Outline   (cont.)  
     Inserting and removi ng single or double - ended 1/4” hex bits .  If the bit to be used is 1/4” single - ended hex
    bit (double - ended bits can be used normally), first insert the M3X12 round head machine screw supplied with
    the screwdriver into the bit opening and screw it in, as sh own on the previous page (optional).
     Hang securely .  During non - operation, the screwdriver should be hung up securely to prevent it from falling
    and also to protect the power cord from sudden pulls.
     Starting and stopping the motor .  Press the trigger (po wer switch) down to start the screwdriver and release
    it to stop.  
     Important Points
     If the clutch slips when screws are fully tightened (i.e., clicking sound is not heard when torque is reached),
    immediately release the trigger (power switch) to prevent   the motor from burning out (due to continued power
    flow while it is not operating).
     If the screwdriver is operating for a long period or if excessive current surges are experienced, the screwdriver
    may overheat.  In this case, it will switch off automati cally.  When the heat has dispersed, normal operation
    can resume.
     Changing the Carbon Brush .  When the carbon brush change indicator lights up red, change it as described
    below.  ( Caution:  Always unplug the screwdriver before changing the brush! )  Only u se the factory
    specification brushes provided with the screwdriver as replacements.
    1. Insert a slotted bit with a 3.0mm wide, 1.0mm thick head in the slot on the side of the carbon maintenance
    bonnet and lever it up, opening the bonnet.
    2. Remove the spr ing resting on the carbon brush.
    3. Lift the copper wire attached to the carbon brush and pull the brush out.
    4. Pull out the tip of the copper wire and complete the removal.
    5. Insert the new carbon brush following the above steps in reverse order.
     A fter Use
     Storage and Maintenance .  If you do not plan to use the screwdriver for a long period, unplug it or switch off
    the power source.  Store the screwdriver in a dry, dust - free place, away from direct sunlight.  Inspect and
    maintain it periodically to   ensure continued functioning.
     Repair .  If the screwdriver is not operating normally, do not attempt to disassemble it.  Contact AIMCO. 
    						
    							Corporate Headquarters  
    1204 E Maple Road   10000 SE Pine Street   Ave. Morones Prieto 2110 Pte.  
    Troy, MI  48083   Portland, OR  97216   Col. Loma Larga  
    248 - 583 - 1180   800 - 852 - 1368   Monterrey ,   NL CP   64710, Mexico  
    FAX 248 - 583 - 7115   FAX 800 - 582 - 9015   52 - 81 - 1001 - 1600  
    www.aimco - global.com FAX  52 - 81 - 1001 - 1630  
    LIT - MAN780   Rev. 
    03/2016  Printed in USA   ©2016 AIMCO  
    						
    All Aimco Brakes manuals Comments (0)

    Related Manuals for Aimco Brakes Screwdriver AE2015 Screwdriver Operation Instructions User Manual