Aimco Brakes MSDSUnivis HVI 26 SPFOil User Manual

							
 
                         7379058-00 UNIVIS HVI 26 
                       MATERIAL SAFETY DATA BULLETIN 
------------------------------------------------------------------------\
--- 
 
------------------------------------------------------------------------\
-- 
1. PRODUCT AND COMPANY IDENTIFICATION 
--------------------------------------------------------------------------  
PRODUCT NAME: UNIVIS HVI 26 
SUPPLIER: EXXON MOBIL CORPORATION 
          3225 GALLOWS RD. 
          FAIRFAX,  VA  22037 
24 - Hour Health and Safety Emergency (call collect):  609-737-4411 
24 - Hour Transportation Emergency (Primary) CHEMTREC: 800-424-9300 
                                           (Secondary) 281-834-3296 
Product and Technical Information: 
Lubricants and Specialties:  800-662-4525   800-443-9966 
Fuels Products:  800-947-9147 
MSDS Fax on Demand: 613-228-1467 
MSDS Internet Website: http://emmsds.ihssolutions.com/ 
 
-------------------------------------------------------------------------- 
2. COMPOSITION/INFORMATION ON INGREDIENTS  
--------------------------------------------------------------------------  
CHEMICAL NAMES AND SYNONYMS: BASE OIL AND ADDITIVES 
GLOBALLY REPORTABLE MSDS INGREDIENTS: 
  Substance Name           Approx. Wt% 
  --------------           ----------- 
  HYDROTREATED LIGHT           65-75 
   NAPHTHENIC DISTILLATE 
   (PETROLEUM) (64742-53-6) 
See Section  8 for exposure limits (if applicable). 
 
-------------------------------------------------------------------------- 
3. HAZARDS IDENTIFICATION 
-------------------------------------------------------------------------- 
Under normal conditions of use, this product is not considered hazardous 
according to regulatory guidelines (See section 15). 
EMERGENCY OVERVIEW: Clear, Colorless Liquid.  Note:  Pressurized mists 
     may form a flammable mixture.  DOT ERG No. :  NA 
POTENTIAL HEALTH EFFECTS: Under normal conditions of intended use, 
     this product does not pose a risk to health.  Excessive exposure 
     may result in eye, skin or respiratory irritation. 
For further health effects/toxicological data, see Section 11. 
 
-------------------------------------------------------------------------- 
4. FIRST AID MEASURES 
--------------------------------------------------------------------------  
EYE CONTACT: Flush thoroughly with water.  If irritation occurs, call 
     a physician. 
SKIN CONTACT: Wash contact areas with soap and water.  Remove and 
     clean oil soaked clothing daily and wash affected area. 
     INJECTION INJURY WARNING:  If product is injected into or under 
     the skin, or into any part of the body, regardless of the 
     appearance of the wound or its size, the individual should be 
     evaluated immediately by a physician as a surgical emergency.  
						

							
     Even though initial symptoms from high pressure injection may be 
     minimal or absent, early surgical treatment within the first few 
     hours may significantly reduce the ultimate extent of injury. 
INHALATION: Not expected to be a problem.  However, if respiratory 
     irritation, dizziness, nausea, or unconsciousness occurs due to 
     excessive vapor or mist exposure, seek immediate medical 
     assistance.  If breathing has stopped, assist ventilation with a 
     mechanical device or mouth-to-mouth resuscitation. 
INGESTION: Not expected to be a problem.  Seek medical attention if 
     discomfort occurs.  Do not induce vomiting. 
 
-------------------------------------------------------------------------- 
5. FIRE-FIGHTING MEASURES 
--------------------------------------------------------------------------  
EXTINGUISHING MEDIA: Carbon dioxide, foam, dry chemical and water fog. 
SPECIAL FIRE FIGHTING PROCEDURES: Water or foam may cause frothing. 
     Use water to keep fire exposed containers cool.  Water spray may 
     be used to flush spills away from exposure.  Prevent runoff from 
     fire control or dilution from entering streams, sewers, or 
     drinking water supply. 
SPECIAL PROTECTIVE EQUIPMENT: For fires in enclosed areas, fire 
     fighters must use self-contained breathing apparatus. 
UNUSUAL FIRE AND EXPLOSION HAZARDS: Note:  Pressurized mists may form 
     a flammable mixture. 
COMBUSTION PRODUCTS: Fumes, smoke, carbon monoxide, sulfur oxides, 
     aldehydes and other decomposition products, in the case of 
     incomplete combustion. 
Flash Point C(F): 94(201) (ASTM D-92). 
Flammable Limits (approx.% vol.in air) -   LEL:  0.9%,   UEL:  7.0% 
NFPA HAZARD ID:   Health: 0,  Flammability: 1,  Reactivity: 0 
 
-------------------------------------------------------------------------- 
6. ACCIDENTAL RELEASE MEASURES 
--------------------------------------------------------------------------  
NOTIFICATION PROCEDURES: Report spills/releases as required to 
     appropriate authorities.  U.S. Coast Guard and EPA regulations 
     require immediate reporting  of spills/releases that could reach 
     any waterway including intermittent dry creeks.  Report 
     spill/release to Coast Guard National Response Center toll free 
     number (800)424-8802.  In case of accide nt or road spill notify 
     CHEMTREC (800) 424-9300. 
PROCEDURES IF MATERIAL IS RELEASED OR SPILLED: 
     LAND SPILL: Shut off source ta king normal safety precautions.  Take 
     measures to minimize the effects on ground water.  Recover by 
     pumping or contain spilled material with sand or other suitable 
     absorbent and remove mechanically into containers.  If necessary, 
     dispose of adsorbed residues as directed in Section 13. 
     WATER SPILL: Confine the spill immediately with booms.  Warn other 
     ships in the vicinity.  Notify port and other relevant authorities. 
     Remove from the surface by skimming or with suitable absorbents.  If 
     permitted by regulatory authorities the use of suitable dispersants 
     should be considered where recommended in local oil spill 
     procedures. 
ENVIRONMENTAL PRECAUTIONS: Preven t material from entering sewers, 
     water sources or low lying areas; advise the relevant authorities 
     if it has, or if it contaminates soil/vegetation.  
						

							
PERSONAL PRECAUTIONS: See Section 8 
 
-------------------------------------------------------------------------- 
7. HANDLING AND STORAGE 
--------------------------------------------------------------------------  
HANDLING: High pressure injection under the skin may occur due to the 
     rupture of pressurized lines.   Always seek medical attention.  No 
     special precautions are necessary beyond normal good hygiene 
     practices.  See Section 8 for additional personal protection 
     advice when handling this product. 
STORAGE: Keep containers closed when  not in use.  Do not store in open 
     or unlabelled containers.  Store away from strong oxidizing 
     agents and combustible materials.  Do not store near heat, 
     sparks, flame or strong oxidants. 
SPECIAL PRECAUTIONS: Prevent small spills and leakages to avoid slip 
     hazard. 
EMPTY CONTAINER WARNING: Empty containers retain residue (liquid 
     and/or vapor) and can be dangerous. DO NOT PRESSURIZE, CUT, WELD, 
     BRAZE, SOLDER, DRILL, GRIND OR EXPOSE SUCH CONTAINERS TO HEAT, 
     FLAME, SPARKS, STATIC ELECTRIC ITY, OR OTHER SOURCES OF IGNITION; 
     THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. Do not attempt to 
     refill or clean container since residue is difficult to remove. 
     Empty drums should be completely drained, properly bunged and 
     promptly returned to a drum reconditioner. All containers should 
     be disposed of in an environmentally safe manner and in 
     accordance with governmental regulations. 
 
-------------------------------------------------------------------------- 
8. EXPOSURE CONTROLS /PERSONAL PROTECTION 
--------------------------------------------------------------------------  
OCCUPATIONAL EXPOSURE LIMITS: 
When mists/aerosols can occur, the following are recommended:  5 mg/m3 
(as oil mist)- ACGIH Threshold Limit Value (TLV), 10 mg/m3 (as oil mist) 
- ACGIH Short Term Exposure Limit (STEL), 5 mg/m3 (as oil mist) - OSHA 
Permissible Exposure Limit (PEL) 
VENTILATION: If mists are generate d, use adequate ventilation, local 
     exhaust or enclosures to control below exposure limits. 
RESPIRATORY PROTECTION: If mists are generated, and/or when 
     ventilation is not adequate, wear approved respirator. 
EYE PROTECTION: If eye contact is likely, safety glasses with side 
     shields or chemical type goggles should be worn. 
SKIN PROTECTION: Not normally required.  When splashing or liquid 
     contact can occur frequently, wear oil resistant gloves and/or 
     other protective clothing.  Good personal hygiene practices 
     should always be followed. 
 
-------------------------------------------------------------------------- 
9. PHYSICAL AND CHEMICAL PROPERTIES  
--------------------------------------------------------------------------  
Typical physical properties are given below.  Consult Product Data Sheet 
for specific details. 
APPEARANCE: Liquid 
COLOR: Clear,Colorless 
ODOR: Mild 
ODOR THRESHOLD-ppm: NE 
pH: NA  
						

							
BOILING POINT C(F): > 154(310) 
MELTING POINT C(F): NA 
FLASH POINT C(F): 94(201) (ASTM D-92) 
FLAMMABILITY (solids): NE 
AUTO FLAMMABILITY C(F): NA 
EXPLOSIVE PROPERTIES: NA 
OXIDIZING PROPERTIES: NA 
VAPOR PRESSURE-mmHg 20 C: < 0.1 
VAPOR DENSITY: > 2.0 
EVAPORATION RATE: NE 
RELATIVE DENSITY, 15/4 C: 0.86 
SOLUBILITY IN WATER: Negligible 
PARTITION COEFFICIENT: > 3.5 
VISCOSITY AT 40 C, cSt:   26.0 
VISCOSITY AT 100 C, cSt: NE 
POUR POINT C(F): -59(-75) 
FREEZING POINT C(F): NE 
VOLATILE ORGANIC COMPOUND: NE 
DMSO EXTRACT, IP-346 (WT.%): 
						

							
     The presence of additives in other tested formulations (in 
     approximately the same amounts as in the present formulation) did 
     not alter the observed effects. 
                  ---SUBCHRONIC TOXICOLOGY (SUMMARY)--- 
No significant adverse effects were found in studies using repeated 
     dermal applications of similar formulations to the skin of 
     laboratory animals for 13 weeks at doses significantly higher 
     than those expected during normal industrial exposure.  The 
     animals were evaluated extensively for effects of exposure 
     (hematology, serum chemistry, urinalysis, organ weights, 
     microscopic examination of tissues etc.). 
                 ---REPRODUCTIVE TOXICOLOGY (SUMMARY)--- 
No teratogenic effects would be expected from dermal exposure, based 
     on laboratory developmental toxicity studies of major components 
     in this formulation and/or materials of similar composition. 
                   ---CHRONIC TOXICOLOGY (SUMMARY)--- 
Repeated and/or prolonged exposure may cause irritation to the skin, 
     eyes or respiratory tract.  Overexposure to oil mist may result 
     in oil droplet deposition and/or granuloma formation.  For 
     mineral base oils:  Base oils in this product are severely 
     solvent refined and/or severely hydrotreated.  Chronic mouse skin 
     painting studies of severely treated oils showed no evidence of 
     carcinogenic effects.  These results are confirmed on a 
     continuing basis using various screening methods such as Modified 
     Ames Test, IP-346, and/or other analytical methods.  For 
     synthetic base oils:  The base oils in this product have been 
     tested in the Ames assay and other tests of mutagenicity with 
     negative results.  These base oils are not expected to be 
     carcinogenic with chronic dermal exposures. 
                      ---SENSITIZATION (SUMMARY)--- 
Not expected to be sensitizing based on tests of this product, 
     components, or similar products. 
 
-------------------------------------------------------------------------- 
12. ECOLOGICAL INFORMATION  
--------------------------------------------------------------------------  
ENVIRONMENTAL FATE AND EFFECTS: 
In the absence of specific environmental data for this product, this 
     assessment is based on information for representative products. 
ECOTOXICITY: Available ectoxicity data (LL50 >1000 mg/L) indicates 
     that adverse effects to aquatic organisms are not expected from 
     this product. 
MOBILITY: When released into the environment, adsorption to sediment 
     and soil will be the predominant behavior. 
PERSISTENCE AND DEGRADABILITY: This product is expected to be 
     inherently biodegradable. 
BIOACCUMULATIVE POTENTIAL: Bioaccumulation is unlikely due to the very 
     low water solubility of this product, therefore bioavailability 
     to aquatic organisms is minimal. 
 
-------------------------------------------------------------------------- 
13. DISPOSAL CONSIDERATIONS  
--------------------------------------------------------------------------  
WASTE DISPOSAL: Product is suitable for burning in an enclosed, 
     controlled burner for fuel value.  Such burning may be limited 
     pursuant to the Resource Conservation and Recovery Act.  In  
						

							
     addition, the product is suitable for processing by an approved 
     recycling facility or can be disposed of at an appropriate 
     government waste disposal facility.  Use of these methods is 
     subject to user compliance with applicable laws and regulations 
     and consideration of product characteristics at time of disposal. 
RCRA INFORMATION:  The unused product, in our opinion, is not 
     specifically listed by the EPA as a hazardous waste (40 CFR, 
     Part 261D), nor is it formulated to contain materials which 
     are listed hazardous wastes.   It does not exhibit the hazardous 
     characteristics of ignitability, corrosivity, or reactivity. The 
     unused product is not formulated with substances covered by the 
     Toxicity Characteristic Leachi ng Procedure (TCLP).  However, used 
     product may be regulated. 
 
-------------------------------------------------------------------------- 
14. TRANSPORT INFORMATION  
--------------------------------------------------------------------------  
USA DOT:  NOT REGULATED BY USA DOT. 
RID/ADR:  NOT REGULATED BY RID/ADR. 
IMO:  NOT REGULATED BY IMO. 
IATA:  NOT REGULATED BY IATA. 
STATIC ACCUMULATOR (50 picosiemens or less):  YES 
 
-------------------------------------------------------------------------- 
15. REGULATORY INFORMATION 
--------------------------------------------------------------------------  
US OSHA HAZARD COMMUNICATION STANDARD: When used for its intended 
     purposes, this product is not classified as hazardous in 
     accordance with OSHA 29 CFR 1910.1200. 
EU Labeling: Product is not dangerous as defined by the European Union 
     Dangerous Substances/Prepa rations Directives. EU labeling not 
     required. 
Governmental Inventory Status: All components comply with TSCA. 
U.S. Superfund Amendments and Reauthorization Act (SARA) Title III: 
  This product contains no EXTREMELY HAZARDOUS SUBSTANCES. 
  SARA (311/312) REPORTABLE HAZARD CATEGORIES: None. 
  This product contains no chemicals subject to the supplier notification 
  requirements of SARA (313) toxic release program. 
The following product ingredients are cited on the lists below: 
CHEMICAL NAME                         CAS NUMBER     LIST CITATIONS 
-------------                         ----------     -------------- 
NAPHTHENIC ACIDS, ZINC SALTS          12001-85-3     22 
(0.02%) 
ZINC NEODECANOATE   (0.02%)           27253-29-8     22 
                    --- REGULATORY LISTS SEARCHED --- 
1=ACGIH ALL  6=IARC 1     11=TSCA 4    16=CA P65 CARC   21=LA RTK 
2=ACGIH A1   7=IARC 2A    12=TSCA 5a2  17=CA P65 REPRO  22=MI 293 
3=ACGIH A2   8=IARC 2B    13=TSCA 5e   18=CA RTK        23=MN RTK 
4=NTP CARC   9=OSHA CARC  14=TSCA 6    19=FL RTK        24=NJ RTK 
5=NTP SUS   10=OSHA Z     15=TSCA 12b  20=IL RTK        25=PA RTK 
                                                        26=RI RTK 
Code key: CARC=Carcinogen; SUS=Suspected Carcinogen; REPRO=Reproductive 
 
-------------------------------------------------------------------------- 
16. OTHER INFORMATION 
--------------------------------------------------------------------------   
						

							
USE: HYDRAULIC OIL 
NOTE: PRODUCTS OF EXXON MOBIL CORPORATION AND ITS AFFILIATED COMPANIES 
ARE NOT FORMULATED TO CONTAIN PCBS. 
Health studies have shown that many hydrocarbons pose potential human 
health risks which may vary from person to person. Information provided 
on this MSDS reflects intended use. This product should not be used for 
other applications. In any case, the following advice should be 
considered: 
INDUSTRIAL LABEL 
Under normal conditions of intended use, this product does not pose a 
risk to health.  Excessive exposure may result in eye, skin or 
respiratory irritation.  Always observe good hygiene measures.  First 
Aid: Wash skin with soap and water.  Flush eyes with water.  If 
overcome by fumes or vapor, remove to fresh air.  If ingested do not 
induce vomiting.  If symptoms persist seek medical assistance.  Read 
and understand the MSDS before using this product. 
************************************************************************* 
For Internal Use Only:  MHC:  1* 1* 1* 1* 1*, MPPEC:  A, TRN: 
7379058-00, CMCS97:  97Q704, REQ:  PS+C, SAFE USE:  L 
EHS Approval Date: 29MAY2002 
************************************************************************* 
 
************************************************************************* 
Legally required information is given in accordance with applicable 
Information given herein is offered in good faith as accurate, but 
without guarantee. Conditions of use and suitability of the product for 
particular uses are beyond our control; all risks of use of the product 
are therefore assumed by the user and WE EXPRESSLY DISCLAIM ALL 
WARRANTIES OF EVERY KIND AND NATURE, INCLUDING WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PA RTICULAR PURPOSE IN RESPECT TO 
THE USE OR SUITABILITY OF THE PRODUCT. Nothing is intended as a 
recommendation for uses which infringe valid patents or as extending 
any license under valid patents. Appropiate warnings and safe handling 
procedures should be providedto handlers and users. Use or re- 
transmission of the information contained herein in any other format 
than the format as presented is strictly prohibited. Mobil neither 
represents nor warrants that the format, content or product formulas 
contained in this document comply with the laws of any other country 
except the United States of America. 
************************************************************************* 
Copyright 1996 Mobil Corporation, All rights reserved