Home > Aimco Brakes > Monitors > Aimco Brakes Monitor ATM11 Tightening Monitor Operations Manual

Aimco Brakes Monitor ATM11 Tightening Monitor Operations Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Aimco Brakes Monitor ATM11 Tightening Monitor Operations Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							30
    I/O (19Pin Connector):
    PIN FUNCTIONWIRE COLOR
    ARX (RS232) Black
    BTX (RS232) White
    CGND Red
    DIN CYCLE (NPN OUT) Green
    EUNUSED Orange
    FBATCH RESET (OPTO IN) Blue
    GSUSPEND (OPTO IN) White/Black
    HPARAM B SELECT (OPTO IN) Red/Black
    JPARAM C SELECT (OPTO IN) Green/Black
    KPARAM D SELECT (OPTO IN) Orange/Black
    LCYCLE ACCEPT (RLY OUT) Blue/Black
    MBATCH ACCEPT (RLY OUT) Black/White
    NREJECT (RLY OUT) Red/White
    PRELAY COMMON (+24VDC OUT) Green/White
    ROPTO COMMON (GND) Blue/White
    SCYCLE ACCEPT (NPN  OUT) Black/Red
    TBATCH ACCEPT (NPN  OUT) White/Red
    UREJECT (NPN OUT) Orange/Red
    VUNUSED Blue/Red
    2 
    						
    							I/O (19Pin Connector continued):
    JP3 and JP5 on this diagram can be found on the back
    board (CE2891) inside the AIM Tightening Monitor. 
    Installing JP5 connects the 24VDC internal power sup
    ply from the relay common (PIN P).  With JP5 discon
    nected, a user supplied voltage can be placed on PIN P
    and that voltage (instead of the internal 24VDC) will be
    returned on pins L, M and N when the relays close.
    Installing JP3 will make inputs FK common with the
    system ground.  Removing JP3 lifts the ground refer
    ence for pins F, G, H, J, K and R.  A user supplied
    ground reference can then be place on pin R in order to
    use the inputs on pins F, G, H, J, K.   
    3
    31 31 
    						
    							32
    DipSwitch:
    Inside the ATM there are two circuit boards.  One of the
    circuit boards is attached to the front panel and the other
    to the back panel.
    Both circuit boards have eight position dipswitches on
    them.  The dipswitch on the front board is reserved for
    factory use only.
    The dipswitch on the back board has a couple of user
    functions.  Position 1 determines where parameters are
    being selected.  If position 1 on the dipswitch is on,
    parameters are selected via the parameter switch.  If
    position 1 is off, parameters may be selected through the
    19pin connector.
    Position 7 on the back board controls the sonalert on the
    front of the unit.  If this dipswitch is on, the beeper will
    work.  If not, the beeper is silenced.
    3 
    						
    							AIMCO CORPORATE HEADQUARTERS
    10000 SE P
    ine Street 
    Portland,
     Oregon   97216 
    Phone: 
    (503) 254–66 00 
    Toll Free: 1-80 0-852-1368 
    AIMCO CHINA 
    Room 607, No.  3998 Hongxin Rd Dibao  Plaza
    Minhang 
    
    District,  Shanghai  
    China 
    Phone: 0086-21-34 3
    19246 
    Fax: 0086-21-34 319245  AIMCO CORPORATION DE 
    ME
    XICO SA DE CV
    Ave. Cristobal  Colon 14529 
    Chihuahua, Chihuahua.   31125 
    Mexico 
    Phone:
    
     (01-61 4) 380-10 10 
    Fax:
    
      (01-61 4) 380-10 19 
    AIMCO SPAIN 
    Avenida Río Gallo, 431  
    19174 Galápagos  - Guadalajara 
    Spain 
    Phone: +  34 673 34  99 25  LIT-MAN760     
    Rev. 03/2016 
    Printed in USA  ©2016 AIMCO     
    						
    All Aimco Brakes manuals Comments (0)

    Related Manuals for Aimco Brakes Monitor ATM11 Tightening Monitor Operations Manual