Home > Aimco Brakes > Cordless Tools > Aimco Brakes Cordless Tool Signature Series SPC2PGM Tool Speed Programmer User Manual

Aimco Brakes Cordless Tool Signature Series SPC2PGM Tool Speed Programmer User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Aimco Brakes Cordless Tool Signature Series SPC2PGM Tool Speed Programmer User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							11
    OnDly×500ms Setting
    For trigger delay after clutch trip option
    Step1: Press “ENTER” for mode 
    selection .
    Press ENTER for mode selection.
    Step 2: Press “” to find the 
    “OnDly x 500ms” Mode then press 
    “EDIT” to enable changes .
    Press EDIT to enter OnDlyx500ms mode.
    Step 3: Press “+” or “–” to select the 
    number of OnDly x 500ms desired .
    (1) “0” setting: Trigger will activate on 
    command without delay between 
    clutch trip  .
    (2) “0 – 120” setting: Trigger will not 
    allow tool to start after clutch 
    trip for chosen value x 500ms  .  
    This setting is typically utilized 
    to reduce the possibility of an 
    operator double tightening a 
    fastener  .
    Increase number.
    Decrease number.
    Step 4: Press “SAVE” and the value will
          be stored into the tool that is
          connected to the programmer  . 
    Press SAVE to complete the setting.
    PROGRAMMER OPERATION 
    						
    							12
    Fwd_W_LED_Tmr Settings:
    To extend the luminosity of LED while in Forward operation 
    Step 1: Press “ENTER” for mode 
    selection .
    Press ENTER for mode selection.
    Step 2: Press “” to find the 
    Fwd_W_LED_Tmr Mode, then press 
    “EDIT” to enable changes .
    Press EDIT for enter  Fwd_W_LED_Tmr Mode.
    Step 3: Press “+” or “– “ to set the 
    amount of time the LED will remain lit 
    while in Forward (CW) operation .  The 
    time can be set from 0 to 60 seconds  . 
    Longer set times may reduce time 
    between battery charges  .
    Increase number
    Decrease number
    Step 4: Press “SAVE” and the value 
    will be stored into the tool that is 
    connected to the programmer  . 
     
    Press  SAVE  to complete the setting   
    PROGRAMMER OPERATION 
    						
    							13
    Rev_W_LED_Tmr Settings:
    To extend the luminosity of LED while in Reverse operation
    Step1: Press “ENTER” for mode 
    selection .
    Press ENTER for mode selection.
    Step 2: Press “” to find the 
    “Rev_W_LED_Tmr” Mode, then press 
    “EDIT” to enable changes .
    Press EDIT to enter  
    Rev_W_LED_Tmr Mode.
    Step 3: Press “+” or “– “ to set the 
    amount of time the LED will remain lit 
    while in Reverse (CCW) operation .  The 
    time can be set from 0 to 60 seconds  . 
    Longer set times may reduce time 
    between battery charges  .
    Increase number.
    Decrease number.
    Step 4: Press “SAVE” and the value 
    will be stored into the tool that is 
    connected to the programmer  . 
    Press SAVE to complete the setting.
    PROGRAMMER OPERATION 
    						
    							14
    INFORMATION MENU
    Product ID
    Built-in information set by factory . 
    Used for production tracking 
    purposes  . Tool S/N is etched into tool 
    housing base at battery slide mount .
     
    Total  Used Time
    Total time the tool motor has 
    operated .  Value is not changeable  .
    Total Count
    Total number of clutch trips that are 
    successful (G) . Clutch trips from 
    double hits are excluded (NG) .  Value 
    is not changeable . 
    Trip Count
    Total number of clutch trips that are 
    successful (G) since value was last 
    cleared .   Clutch trips from double hits 
    are excluded (NG)  Press “ERASE” to 
    reset Trip CNT to zero  . 
    The following programmer details can be seen under information menu . 
    						
    							15
    NOTES 
    						
    							16
    Corporate Headquarters 10000 SE Pine Street Portland, OR 97216800-852-1368FAX 800-582-9015www.aimco-global.com
    Ave.Cristóbal Colon 14529Chihuahua, Chihuahua. 31125Mexico011-52-(614) 380-1010FAX 011-52-(614) 380-1019
    LIT-MAN255, Rev. 01/14Printed in USA©2013 AIMCO 
    						
    All Aimco Brakes manuals Comments (0)

    Related Manuals for Aimco Brakes Cordless Tool Signature Series SPC2PGM Tool Speed Programmer User Manual