Home
>
Aimco Brakes
>
Assembly Systems
>
Aimco Brakes Assembly System A50 Standard Screw Presenter Operations Manual
Aimco Brakes Assembly System A50 Standard Screw Presenter Operations Manual
Have a look at the manual Aimco Brakes Assembly System A50 Standard Screw Presenter Operations Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
- 9 - Troubleshooting Guide MALFUNCTION POSSIBLE PROBLEM REMEDY Machine does nothing when power is on. Rail is already full. Begin system use. Screws not advancing to stopper. zScrews are too big or too small for rail. zNot enough sc re ws in cham be r. zScrews are sitting on top of rail. zUse a suitable rail. zAdd screws. zAdjust the height of the bru s h (see adj. #2). zAdjust the height of the shutter board (see a d j. #3). Screws fall into rail groove. z Rail size is too big. zLength of screw is s horter than width of rail’s groove. zChange to the correct rail. zScrews will not work in ma chi ne. Screws do not move smoothly on rail. zThe gap between the rail cove r and the scre w he ad is too small. zThe top-end of the rail is dirty. zAdjust the bits guide a ssem bly (se e adj. #2 ). zRaise incline machine. zClean rail and bits guide. A wrong posture screw passed through shutter board. Incorrect height adju stment of shutter board. Adjust shutter board. Screws do not move to stopper. zScrews were stopp ed on th e way to the stopper. zIncorrect front/rear adju s tment of rail. zAdjust bit guide assembly (rail cov er a dj.). zRail front/rear adju s tment (see ad j. #1).
-10- Troubleshooting Guide (cont.) MALFUNCTION POSSIBLE PROBLEM REMEDY Bit not engaging screw head easily. zRail position inc orrec t. zBit guide position inc orrec t. zAdjust rail to prop er positio n (se e adj. #1 ). zAdjust bits guide and rail cove r to prop er positio n (se e adj. #4 ). Machine suddenly does not work. zProtection circuit c aused by overload . zDid not pick up the sc rew which wa s locate d on th e stopp er for m ore than one se cond. zTurn off power then on ag ain. If machi ne still does not work, ove r load sc rews on chambe r. zTake some screws out of chambe r. Screws fall into machine through rail opening. zShake out screws throug h holes in bottom of machine.
-11- Maintenance MAINTENANCE 1. Remove power supply plug. 2. Turn off power before maintenance. 3. Remove all screws from the screw chamber and rail prior to maintenance. CLEANING Clean Rail 1. Remove rail from machine. Loosen rail fix screw located on the top left of front panel (see Figure 17). 2. Clean rail surface with softcloth moistened with alcohol. Clean Rail Guide’s Wall Clean the surface of rail guide’s wall with a soft cloth moistened with alcohol (see Figure 18). REPLACEMENTS Rail Replacement After cleaning, if screws do not advance more smoothly, rail replacement may be necessary.
-12- Maintenance (cont.) BRUSH REPLACEMENT 1. Turn the brush face down.Insert 2mm hex wrench in timing axis. Hold and turn clockwise until brush is in the vertical position. 2. Loosen brush fix screws.Remove and replace brush with new brush as shown in Figure 19. 3. Rotate brush assemblyback to horizontal position by turning hex wrench clockwise.
-14- Warranty ACRA-FEED® A-50 WARRANTY AIMCO/AcraDyne warrants the A-50 Screwfeeder to be free of material or manufacturing-related defects (except for normal wear) for a period of one (1) year from original shipment. This warranty is based on usage generated in an eight-hour workday.
Corporate Headquarters 10000 SE Pine Street Portland, OR 97216 800-852- 1368 FAX 800- 582-9015 www.aimco-global.com Ave. Cristóbal Colon 14529 Chihuahua, Chihuahua. 311 25 Mexico 011- 52-(614) 380-1010 FAX 011- 52-(614) 380- 1019 LIT-MAN 830 Rev. 03/2016 Printed in USA ©2016 AIMCO