Aimco Brakes AcraDyne ErgoArms Operations Manual

PO Box 1\f4\f0, Portland OR 97\b9\b-04\f0  • 800-85\b-13\f8 • Fax 800-58\b-9015www.aimco-global.com
ERGO-ARM
Tool Support Systems
Operations Manual
MODELS AD-D1098S/SAC& AD-D1098P/PAC
Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd  \f/\b/2013\:  \f:46 AM  Page 1 

I N T R O D U C T I O N
2
CAUTION!
Please read the following manual before assembling and operating your ErgoArm Tool Support System\b
As  in  all  cases,  when  electric  or  air  lines  come  in  close  contact  with  moving  parts  or  mechanisms,  precautions  should  be
taken by the person installing and operating the equipment that these cords or hoses do not become entangled or damaged
by moving parts\b Proper attention will prevent possible hazard or injury.
R E C O M M E N D E D   T O O L S   \b...

3
I N S T A L L A T I O N   A N D   S E T   U P   I N S T U C T I O N S   -   A L L   M O D E L S
1.Remove  the TABLE MOUNT from the box\b
\b. Bolt to work surface\b It is important to level the table mount so that the post is 90 degrees to the work surface through full range of
travel (see VIEW #1)
3. Insert  POSTinto mount, and tighten set screws\b
4. Remove  remaining  body  of  ErgoArm  from  box  and  slide  ADJUSTABLE  SHOULDER  CLAMPover POST\b  Tighten  screws  at  desired
height  (see VIEW...

4
I N S T A L L A T I O N   A N D   S E T   U P   I N S T U C T I O N S   -   A L L   M O D E L S
The VERTICAL ADJUSTMENT ROD (Item #41) allows the tool to be adjusted from zero degrees (parallel to column), up to 15 degrees
in either direction from zero point\b This compensates for any irregularities in the workpiece or if application requires fastener to be 
driven in at an angle (see View #3)\b This does not take the place of properly leveling the Table Mount Flange\b Use for final 90 degree...

\b
I N S T A L L A T I O N   A N D   S E T   U P   I N S T U C T I O N S   -   A L L   M O D E L S
To  increase  the  reach  capability  of  the  ErgoArm,  remove  the  ring  pin  (Item  #14)  from  the CYLINDER  MOUNTING  YOKEROD  END
(Item #1\f)\b
Pull  the  FOREARM  INSERT (Item  #13)  out,  away  from  the  arm,  the  desired  reach,  up  to  an  additional  5\b  Once  desired  reach  is 
achieved, align holes in  FOREARMand FOREARM INSERT, reinsert ring pin in  CYLINDER MOUNTING YOKEROD END (Item...

6
PAR TS  B R EAK DO W N
Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd  \f/\b/2013\:  \f:46 AM  Page 6 

7
P A R T S   B R E A K D O W N
Ergo Arm Operations \:Manual_3000 nutrunner\: manual.qxd  \f/\b/2013\:  \f:46 AM  Page 7 

E R G O - A R M   B R E A K D O W N
Index PartNu\fber Nu\fberDes\briptionQty
1 EA14Table Flange1
2 EA01 Post1
\f  EA02 Shoulder Clamp1
4  EA44 1\b420 x 11\b4 Cap Screw 2
5  EA0\f Bearing4
6 EA04 1\b21\f x 4 Double Ended Stud 2
7 EA05 1\b21\f Locking Nut 2
8  EA21 Label2
9  EA06 Upper Arm 1
10  EA07 Elbow1
11 EA10 Forearm1
12  EA09 Cyl. Mtg. Yoke Rod End 1
1\f EA11 Forearm Insert1
14  EA18 1\b4 x 15\b8 Cotterless Clevis Pin 1
15  EA17 \f\b16 x \f\b4 Clevis Pin 1
16  EA1\f Hair Pin Cotter1
17  EA20 8\f2 x...

Notes: